NXP Semiconductors

TJA1042T/3/CM - 1 Mbps CAN Transceiver | NXP

MPN: TJA1042T/3/CM ✗ اختتامِ زندگی
4.5 V to 5.5 V Vdss 8-pin SOIC Package
MOQ: 1 |

TJA1042T/3/CM جائزہ

The NXP TJA1042T/3/CM is a high-speed CAN physical-layer transceiver with a 1 Mbps maximum data rate, a 5 V transceiver supply, and a 3.3 V or 5 V microcontroller interface. The device is packaged in an 8-pin SOIC and provides differential bus transmit and receive functions for automotive and industrial Controller Area Network systems.

A CAN transceiver, also called a CAN physical-layer interface, converts logic-level signals from a CAN protocol controller into differential signals for the two-wire CAN bus. It also converts differential bus levels back into a controller-compatible receive signal. Within the hierarchy of interface ICs, the TJA1042T/3/CM implements the physical layer beneath the CAN protocol controller, while leaving message arbitration, framing, error handling, and protocol execution to the controller.

The TJA1042T/3/CM combines a 3.3 V or 5 V VIO interface with a high-speed CAN channel operating up to 1 Mbps. Standby mode reduces current consumption when the node does not need to transmit or receive. Bus wake-up capability permits a sleeping node to react to activity on the CAN bus, while passive behavior when unpowered helps define the state of the bus during shutdown or power-loss conditions.

The TJA1042T/3 version uses the VIO pin rather than the SPLIT function found on non-VIO TJA1042T and TJA1042CT variants. VIO allows the CAN controller-side interface voltage to be selected independently from the transceiver supply. This is particularly useful when the CAN controller operates at 3.3 V while the CAN physical layer uses a 5 V supply. The device supports differential transmit and receive and is designed for high-speed automotive CAN networks.

Typical applications include vehicle powertrain and body electronics, industrial automation equipment, building automation, robotics controllers, diagnostic systems, and distributed industrial sensors. Its standalone SOIC package also supports designs where the protocol controller and transceiver are separated for routing, isolation, or power-management reasons.

PCB design should preserve the CAN bus differential route and place termination only at the physical ends of the bus. Keep the CANL and CANH traces short, matched, and away from noisy switching nodes. Confirm VCC and VIO sequencing, respect the absolute maximum ratings, and verify wake-up and standby behavior against the system power-state requirements.

This page organizes the NXP transceiver’s key characteristics, sourcing information, drop-in replacement considerations, pin functions, and application guidance to support faster component evaluation and PCB design.

کے لیے ڈراپ اِن متبادل TJA1042T/3/CM — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں TJA1042T/3/CM (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Operating Temperature Range, Package, Product Type.

Texas Instruments
Operating Temperature Range: -55°C to +125°C
Package: 8-SOIC
Product Type: Fault-protected CAN transceiver

TCAN1042HD

✅ ڈراپ-اِن
Texas Instruments
📦 SOIC-8
Fault-protected CAN transceiver · Classic CAN and CAN FD · 2 Mbps · 1 · 1 · 4.5 V to 5.5 V · -55°C to +125°C · 8-SOIC

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

TJA1042T/3/CM تفصیلات

Product Type High-speed CAN physical-layer transceiver
Maximum CAN Data Rate 1 Mbit/s
Transceiver Supply Voltage VCC 4.5 V to 5.5 V
Controller Interface Supply Voltage VIO 2.8 V to 5.5 V
VIO Operating Modes 3.3 V or 5 V microcontroller interface
CAN Bus Interface 2-wire differential CAN bus
Operating Mode High-speed mode
Power-Saving Mode Standby mode with bus wake-up capability
Unpowered Behavior Passive behavior
Interface Function Differential transmit and receive
Microcontroller Interface TXD and RXD signals
پیکیج 8-pin SOIC
ماؤنٹنگ ٹائپ Surface mount
آپریٹنگ درجہ حرارت رینج -40 °C to +125 °C
IEC 61000-4-2 ESD Protection ±8 kV contact discharge and ±15 kV air discharge
RoHS اسٹیٹس Compliant
REACH Status Compliant
Lead-Free Status Lead-free

TJA1042T/3/CM پن کنفیگریشن

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پن 1 TXD — Transmitter data input from the CAN controller
پن 2 GND — Ground connection
پن 3 VCC — Transceiver supply voltage input
پن 4 RXD — Receiver data output to the CAN controller
پن 5 VIO — Controller-side interface supply voltage input
پن 6 CANL — CAN bus low input and output
پن 7 CANH — CAN bus high input and output
پن 8 STB — Standby mode control input

عام استعمالات

TJA1042T/3/CM کے لیے موزوں ہے 6 ایپلیکیشنs: Automotive Body Control Network, Industrial Automation Controller, Vehicle Diagnostic Gateway, Robotics Network Node, Building Automation Sensor Hub, Distributed Industrial Sensor Node.

🚗

Automotive Body Control Network

The TJA1042T/3/CM fits automotive body-control modules that require a 1 Mbit/s CAN physical layer while the host microcontroller operates from 3.3 V. Its VIO input range of 2.8 V to 5.5 V supports direct connection to a 3.3 V CAN controller, while VCC powers the bus-side interface from 5 V. Differential transmit and receive preserve noise immunity in a vehicle environment, and standby mode reduces consumption when the module is inactive.

🏭

Industrial Automation Controller

Industrial automation equipment can use the TJA1042T/3/CM to connect a controller to a field-level CAN bus carrying sensor commands, machine status, and diagnostic data. The transceiver supports communication rates up to 1 Mbit/s and separates the 2.8 V to 5.5 V controller-side VIO supply from the 5 V CAN side. Standby operation is useful for cyclic machines that spend time idle, while bus wake-up supports recovery from a low-power state when another node initiates traffic.

🚗

Vehicle Diagnostic Gateway

A vehicle diagnostic gateway benefits from the TJA1042T/3/CM because the device provides a high-speed differential CAN interface with a separate 3.3 V-compatible VIO rail. This allows a low-voltage gateway processor to communicate through a 5 V CAN physical layer without level-shifting every digital interface signal. Bus wake-up permits the gateway to activate when required, and passive unpowered behavior helps define the node state during ignition-off or supply-ramp conditions.

🤖

Robotics Network Node

The TJA1042T/3/CM is suitable for robot controllers that distribute actuator commands and collect position or fault information over a CAN bus. Its 1 Mbit/s capability supports responsive communication between motion-control and sensor nodes, while the VIO interface can operate directly with 3.3 V logic. Differential signaling improves noise immunity around motor drives and relays, although the PCB must maintain a controlled bus topology and place termination only at the two bus endpoints.

🧩

Building Automation Sensor Hub

A building-automation sensor hub can use the TJA1042T/3/CM to bridge a low-voltage controller to a 5 V CAN backbone operating at up to 1 Mbit/s. The separate VIO supply supports 3.3 V or 5 V host logic, and standby mode reduces consumption in rooms or zones that do not require continuous communication. Bus wake-up allows the hub to respond when another building controller starts a network transaction, supporting distributed HVAC, lighting, and access-control systems.

🔧

Distributed Industrial Sensor Node

Distributed sensor nodes can use the TJA1042T/3/CM when several remote measurement devices must exchange readings over a shared CAN network. The device combines a 1 Mbit/s physical layer with a 3.3 V-compatible VIO interface, reducing the need for external digital level translation. Standby mode lowers demand when measurements are not being reported, and wake-up capability allows a node to react to scheduled remote commands. Power and ground design should prevent conducted noise from coupling into CANL or CANH.

تجویز کردہ پروڈکٹس کا خلاصہ

TJA1042T/3/CM NXP Semiconductors استعمال ہوتا ہے: Automotive Body Control Network, Industrial Automation Controller, Vehicle Diagnostic Gateway, Robotics Network Node, Building Automation Sensor Hub, Distributed Industrial Sensor Node SJA1000 CAN protocol controller استعمال ہوتا ہے: Automotive Body Control Network, Industrial Automation Controller, Vehicle Diagnostic Gateway, Robotics Network Node, Building Automation Sensor Hub, Distributed Industrial Sensor Node MCP2515 Microcontroller CAN controller interface استعمال ہوتا ہے: Automotive Body Control Network, Vehicle Diagnostic Gateway, Robotics Network Node, Building Automation Sensor Hub, Distributed Industrial Sensor Node TJA1051T/118 Related high-speed CAN interface استعمال ہوتا ہے: Industrial Automation Controller
What are the key specifications of TJA1042T/3/CM that engineers should know?
The TJA1042T/3/CM is a high-speed CAN physical-layer transceiver rated for data rates up to 1 Mbit/s, with a 4.5 V to 5.5 V transceiver supply and a 2.8 V to 5.5 V VIO interface. According to the NXP manufacturer datasheet, the device provides differential transmit and receive, standby operation, bus wake-up capability, and passive behavior when unpowered. It is offered in an 8-pin SOIC package for surface-mount industrial and automotive designs.
Where can I download the TJA1042T/3/CM datasheet PDF?
The official TJA1042 manufacturer datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/TJA1042.pdf. It contains the pin descriptions, electrical characteristics, application diagram, timing information, and guidance for VIO, standby, bus wake-up, termination, and PCB layout. Use the TJA1042T/3 sections for the VIO-equipped device rather than the SPLIT-pin configurations described for other family members.
Where can I find the TJA1042T/3/CM pinout?
The TJA1042T/3/CM uses an 8-pin SOIC. According to the NXP manufacturer datasheet, pin 1 is TXD, pin 2 is GND, pin 3 is VCC, pin 4 is RXD, pin 5 is VIO, pin 6 is CANL, pin 7 is CANH, and pin 8 is STB. The pin-description table and package drawing in the official datasheet should be used when assigning PCB tracks and verifying controller signal directions.
What is the difference between VIO and SPLIT on TJA1042T/3/CM?
Pin 5 on the TJA1042T/3/CM is VIO, which powers the controller-side digital interface and permits operation with 3.3 V or 5 V CAN controllers. NXP documentation identifies SPLIT on pin 5 of the TJA1042T and TJA1042CT as a different function used with split termination. The TJA1042T/3 therefore cannot replace a SPLIT-pin TJA1042T without changing the PCB connection at pin 5.
What is the operating voltage of TJA1042T/3/CM?
The TJA1042T/3/CM operates from a 4.5 V to 5.5 V transceiver supply at VCC and accepts a 2.8 V to 5.5 V controller-interface supply at VIO. According to the NXP manufacturer datasheet, the separate VIO range supports direct connection to both 3.3 V and 5 V CAN protocol controllers while maintaining a 5 V CAN physical-layer supply.
Can TJA1042T/3/CM communicate with a 3.3 V CAN controller?
Yes. The TJA1042T/3/CM is specifically designed to connect a 3.3 V CAN controller through its VIO interface while the CAN transceiver side operates from 5 V. The VIO input range extends from 2.8 V to 5.5 V, as specified by the NXP manufacturer datasheet. This makes the device appropriate for 3.3 V microcontrollers that lack a 5 V-tolerant CAN controller interface.
Does TJA1042T/3/CM support standby and bus wake-up?
Yes. The TJA1042T/3/CM includes a low-power standby mode and bus wake-up capability. According to the NXP manufacturer datasheet, the STB input controls the operating state, and a node in standby can detect qualifying CAN bus activity to wake the system. The interface also has defined passive behavior when the device is unpowered, which helps maintain predictable bus operation during shutdown transitions.
Where can I buy TJA1042T/3/CM online?
Use the Request a Quote form on this page to request TJA1042T/3/CM pricing, current availability, and order confirmation. The form is the appropriate route for obtaining a current commercial quotation without relying on a stale listing. For technical confirmation, identify the complete orderable code and package variant with the supplier, since NXP uses suffix coding to distinguish order configurations.
What is the price of TJA1042T/3/CM?
Current TJA1042T/3/CM pricing is available through the Request a Quote form on this page. Submit the required quantity, package configuration, and delivery location so the quotation can reflect current supply and order conditions. Because market pricing can change, the request form is preferable to reproducing an outdated price in technical documentation or design-review material.
What is the lead time for TJA1042T/3/CM?
Request the current lead time through the Request a Quote form on this page. The part is listed as NRND by NXP, so procurement planning should include confirmation of inventory, replenishment status, and the exact orderable suffix required for the intended package and delivery format. The Request a Quote response should also state any minimum-order or batch constraints applicable to the order.
Is TJA1042T/3/CM in stock?
Check current availability by submitting the Request a Quote form on this page. NXP lists the TJA1042T as NRND, and the requested configuration should therefore be confirmed before committing a production schedule. Include the required quantity, reel or tray format, and shipping destination in the request so the response can reflect the appropriate supply channel and delivery plan.
TJA1042T/3/CM vs TCAN1042H - which is better for a 3.3 V CAN controller design?
The TJA1042T/3/CM is the stronger choice when the design specifically requires a low VIO minimum or NXP sourcing continuity. NXP specifies a 2.8 V minimum VIO for the TJA1042T/3, while the TCAN1042H comparison information identifies 3.0 V for the TI device. TI also identifies a lower VCC undervoltage threshold for the TJA1042, although the exact logic thresholds should be checked in each datasheet before replacement.
What is the difference between TJA1042T/3/CM and TCAN1042H?
Both devices implement a high-speed CAN physical layer and can be considered for related 8-pin interface layouts, but their voltage thresholds and secondary functions are not identical. The TI comparison notes a 2.8 V versus 3.0 V minimum VIO and a 3.5 V versus 3.8 V VCC undervoltage threshold. Confirm pin names, standby polarity, wake-up behavior, and every electrical threshold in the NXP and TI datasheets before treating either device as interchangeable.
When should I choose TJA1042T/3/CM over TCAN1042H?
Choose the TJA1042T/3/CM when continuing an NXP-based CAN design, using a controller interface below the TCAN1042H minimum VIO, or requiring a proven NXP supply path is more important than redesigning around a different manufacturer. The device supports 3.3 V and 5 V controller interfaces, 1 Mbit/s operation, standby mode, and bus wake-up in an 8-pin SOIC. Final selection should also account for lifecycle status and regional procurement constraints.
Is TJA1042T/3/CM suitable for industrial CAN bus equipment?
Yes, the TJA1042T/3/CM is suitable for industrial CAN equipment that uses a 5 V physical layer and a 3.3 V or 5 V controller interface. According to the NXP manufacturer datasheet, the device supports rates up to 1 Mbit/s, an operating range of -40 °C to +125 °C, standby mode, and bus wake-up. Its industrial suitability should be evaluated alongside the complete system EMC, surge, grounding, and isolation requirements.
What can replace TJA1042T/3/CM?
The TJA1042T/3/CM can be evaluated against TCAN1042H because the TI interface documentation identifies it as a replacement option for TJA1042 devices. It is not an unconditional drop-in choice: the two devices have different minimum VIO and VCC undervoltage thresholds, and their output specifications are measured differently. Verify pin 5, STB behavior, bus wake-up, logic levels, and all timing limits against the original design before approval.
Is TCAN1042H the same as TJA1042T/3/CM?
No. TCAN1042H is a functional alternative for many CAN physical-layer designs, but it is not electrically identical to the TJA1042T/3/CM. The devices differ in minimum VIO, VCC undervoltage detection, measurement conventions, and potentially secondary mode behavior. The TI interface guidance states that the differences are minimal for many applications, but it still recommends checking the original schematic and relevant electrical specifications before replacement.
What is the best Texas Instruments equivalent for TJA1042T/3/CM?
TCAN1042H is the best directly identified Texas Instruments equivalent to evaluate for TJA1042T/3/CM because the TI interface guidance specifically discusses it as a TJA1042 replacement. The comparison identifies a 2.8 V versus 3.0 V minimum VIO and a 3.5 V versus 3.8 V VCC undervoltage threshold. These differences require schematic review, especially when the controller operates at 3.3 V or the design depends on power-state transitions.

کے لیے انجینئرنگ ریفرنس ڈیٹا TJA1042T/3/CM — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the TJA1042T/3/CM when maintaining an NXP-based CAN design, supporting a controller interface down to 2.8 V, or retaining the combination of 1 Mbit/s operation, standby mode, bus wake-up, and passive unpowered behavior is important. Its separate VIO supply permits a 3.3 V controller to communicate with a 5 V CAN physical layer. TCAN1042H is worth evaluating when supply-chain consolidation or a second-source strategy justifies a functional review, but its 3.0 V minimum VIO and 3.8 V VCC undervoltage threshold differ from the NXP device. A non-VIO TJA1042T with SPLIT at pin 5 is not a direct substitute because the pin function changes. For all alternatives, verify STB polarity, wake-up timing, logic thresholds, ESD performance, and supply sequencing before releasing a PCB revision.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ TCAN1042H
Brand NXP Semiconductors Texas Instruments
Package SOIC-8 SOIC-8
Maximum CAN Data Rate 1 Mbit/s 1 Mbit/s
Transceiver Supply Voltage VCC 4.5 V to 5.5 V 4.5 V to 5.5 V
Controller Interface Supply Voltage VIO 2.8 V to 5.5 V 3.0 V to 5.5 V
Minimum VIO 2.8 V 3.0 V
VCC Undervoltage Detection 3.5 V 3.8 V
Power-Saving Function Standby mode with bus wake-up capability Standby mode

اہم امتیازی خصوصیات

  • Lower minimum VIO for controller-side interfacing (بمقابلہTCAN1042H)
  • Earlier VCC undervoltage detection (بمقابلہTCAN1042H)
  • Integrated bus wake-up and standby behavior (بمقابلہTCAN1042H)

ڈیزائن نوٹس

Route CANH and CANL as a close, length-matched differential pair and connect the 120 Ω termination only at the physical ends of the bus. Avoid stubs, test pads, and abrupt changes in layer geometry. Place the common-mode choke, termination network, and transceiver according to the NXP TJA1042 application guidance so that high-frequency CAN edges are not distorted by excessive trace or component parasitics.

Decouple VCC and VIO locally with the capacitance specified by the NXP manufacturer datasheet, and place the components at the associated pins rather than near the bus connector. Keep the 5 V CAN-side supply and 3.3 V or 5 V controller-side supply paths separate to prevent controller transients from coupling into the transceiver. Review startup, shutdown, and standby transitions to ensure no input is driven outside its supply limits.

Do not confuse pin 5 of the TJA1042T/3/CM with SPLIT. Pin 5 is VIO on this version, while SPLIT belongs to other TJA1042 family variants and is intended for split-termination circuitry. Confirm STB polarity and wake-up timing in the system controller. A pin-compatible-looking substitution can still change bus startup behavior even when its package and nominal data rate match.

تعمیل کی معلومات

RoHS
Compliant
REACH
Compliant
AEC-Q100
Not Applicable
لیڈ فری
Yes
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The TJA1042 family is identified as RoHS and REACH compliant and lead-free. No specific AEC-Q100 qualification, halogen-free declaration, or conflict-minerals statement was identified for this exact order configuration.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-18 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

tja1042t datasheet tja1042t 1j nxp TJA1042T/3/CM datasheet TJA1042T/3/CM datasheet pdf TJA1042T/3/CM pinout TJA1042T/3/CM equivalent TJA1042T/3/CM replacement TJA1042T/3/CM vs TCAN1042H TJA1042T/3/CM SOIC-8 TJA1042T/3/CM price TJA1042T/3/CM stock NXP TJA1042T/3/CM

متعلقہ اجزاء اور اصطلاحات

NXP Semiconductors TJA1042T/3/CM TJA1042T TCAN1042H Texas Instruments CAN transceiver CAN physical layer Controller Area Network CAN protocol controller high-speed CAN differential transmit and receive VIO interface standby mode bus wake-up passive behavior SOIC-8 surface-mount package 3.3 V CAN controller 5 V CAN bus 1 Mbit/s data rate CANL CANH ISO 11898 RoHS REACH
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں