STMicroelectronics

TS339IPT - Micropower Quad Open-Drain Comparator | ST

MPN: TS339IPT ✓ فعال
3 V to 16 V Vdss 9 μA per comparator Id TSSOP-14 Package
MOQ: 1 |

TS339IPT جائزہ

The STMicroelectronics TS339IPT is a micropower quad CMOS voltage comparator with four open-drain outputs, extremely low typical supply current of 9 μA per comparator, and operation across a 3 V to 16 V supply range. The device is packaged in a 14-pin TSSOP package and is intended for low-voltage, low-power signal-conditioning systems.

A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input exceeds the inverting input. The TS339 belongs to the comparator hierarchy, combining four independent comparator channels with CMOS input stages and open-drain outputs. The TS339 family provides a practical alternative to higher-current bipolar LM339-family comparators in battery-powered and portable equipment.

Key features include four comparator channels, a typical input common-mode range extending from ground to VCC minus 1.5 V, an output sink capability of 40 mA, and open-drain outputs that can be pulled up to a chosen external voltage. The low 9 μA typical current per comparator supports low-power sensing, while the 16 V maximum supply rating permits operation from a 3 V supply through higher-voltage industrial rails. These characteristics make the device suitable for threshold detection, battery monitoring, signal conditioning, and sensor interfaces.

The open-drain architecture provides flexible output voltage levels but requires an external pull-up resistor on every output. The pull-up resistor establishes the high output level, while the output transistor actively pulls the line toward ground. This arrangement permits wired logic, level translation, and wired-AND behavior, although designers must account for the rise time created by the resistor and total bus capacitance. Input common-mode and output-level requirements must be checked against the actual supply voltage.

Typical applications include portable battery monitoring, industrial sensor interfaces, window or level comparators, overvoltage detection, and low-power control systems. Because the TS339IPT is specified for the industrial temperature range, it can also be used in equipment exposed to temperatures from −40 °C to +125 °C. The 14-pin TSSOP package supports compact, surface-mount assembly but is relatively narrow and requires careful component placement.

When designing a PCB around the TS339IPT, route the comparator inputs away from switching nodes and provide a short, quiet ground reference for each sensing point. Place pull-up resistors close to the corresponding open-drain outputs to minimize trace capacitance and improve switching speed. Confirm that the logic high generated by the pull-up meets the receiving device's input threshold, and verify that no signal connected to either comparator input exceeds the datasheet's absolute maximum ratings.

This page combines the TS339IPT's principal electrical characteristics, verified package and distributor information, application guidance, comparison data, and practical replacement considerations to support faster component selection and board-level design.

کے لیے ڈراپ اِن متبادل TS339IPT — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

TSX339IPT

✅ ڈراپ-اِن
📦 TSSOP-14
Typical supply current is 5 μA versus 9 μA per comparator for TS339IPT, while both use a 14-TSSOP package and open-drain outputs

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

TS334IPT

✅ ڈراپ-اِن
📦 TSSOP-14
Supply-voltage range is 1.6 V to 5 V versus 3 V to 16 V for TS339IPT; both are quad open-drain comparators in 14-TSSOP packages

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

TS3704IPT

✅ ڈراپ-اِن
📦 TSSOP-14
Uses push-pull CMOS outputs instead of open-drain outputs, eliminating the external pull-up resistor required by TS339IPT

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

TS339IPT زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

Comparator Type 4-channel general-purpose voltage comparator
Technology CMOS
آؤٹ پٹ کی قسم Open drain
Number of Channels 4 channels
Supply Voltage Range 3 V to 16 V
Typical Supply Current 9 μA per comparator
Input Common-Mode Range 0 V to VCC − 1.5 V
Output Sink Current 40 mA
آپریٹنگ درجہ حرارت رینج −40 °C to +125 °C
پیکیج TSSOP-14
ماؤنٹنگ ٹائپ Surface mount

TS339IPT tssop-14 پن کنفیگریشن گائیڈ

TS339IPT (tssop-14 پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔

TS339IPT کے لیے tssop-14 پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں TS339IPT.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

TS339IPT کے لیے موزوں ہے 6 ایپلیکیشنs: Portable Battery Monitoring, Industrial Sensor Threshold Detection, Overvoltage and Power Rail Detection, Window and Level Comparators, Battery-Powered Environmental Sensing, Motor and Actuator Limit Detection.

📱

Portable Battery Monitoring

The TS339IPT is suitable for monitoring battery-derived rails in portable instruments because four independent comparator channels can support multiple threshold checks without requiring four separate packages. Its typical 9 μA per-comparator consumption is well suited to low-power sensing, while the 3 V to 16 V supply range accommodates common single-cell and industrial battery systems. Each open-drain output can pull up to a selected system logic level through an external resistor, allowing a microcontroller input to remain compatible even when the comparator operates from a different rail. The design should account for the upper common-mode limit of VCC minus 1.5 V and choose pull-up values that balance battery consumption against switching speed.

🏭

Industrial Sensor Threshold Detection

The TS339IPT fits industrial sensor interfaces that convert an analog measurement into a switching event, such as pressure, temperature, or level sensing. Four channels provide independent comparisons, while 9 μA typical current per comparator reduces the load imposed by always-on sensing circuitry. The industrial temperature range of −40 °C to +125 °C supports equipment operating across demanding ambient conditions. Designers should place input traces away from motors, relays, and switching-power nodes, then reference each comparator input to a quiet ground region. Open-drain outputs simplify wired alarm or fault signaling when each line receives a pull-up to the appropriate control-logic voltage.

⚡

Overvoltage and Power Rail Detection

The TS339IPT can supervise multiple power rails by comparing divided input voltages against precise references. Its operating supply range of 3 V to 16 V allows the comparator itself to operate across common industrial voltage levels, and its open-drain output can directly pull down a fault line or alert signal. The comparator's input common-mode ceiling of VCC minus 1.5 V means divider and reference design must keep both inputs inside the valid range, including during fault conditions. A pull-up resistor is required on every fault output. This arrangement is useful for battery packs, external power modules, and board-level protection where an open-drain fault bus provides a simple wired fault indication.

🔧

Window and Level Comparators

The TS339IPT is appropriate for implementing upper and lower window limits, tank-level detection, or simple mechanical position sensing. Two channels can establish the lower and upper thresholds around a reference, while the other channels can monitor additional sensor points. The quad architecture reduces package count compared with discrete single comparators and preserves the low 9 μA typical per-channel current. For slowly changing sensor signals, add suitable hysteresis to prevent output chatter around the threshold. Because the outputs are open drain, pull-ups can be tied to the receiving system's logic rail, and multiple fault conditions can be combined into a common wired-alert line where the circuit architecture permits it.

🧩

Battery-Powered Environmental Sensing

The TS339IPT can support low-duty-cycle environmental sensing systems that compare thermistor, light, or humidity-sensor outputs against preset limits. Its four channels allow several alarms to be evaluated locally without waking a main controller for every measurement, while the low typical supply current helps preserve battery life. The 3 V minimum supply supports low-voltage sensor nodes, and the 16 V maximum rating provides margin for protected industrial installations. Keep comparator inputs short and use a quiet analog ground because switching activity and long sensor traces can shift the apparent threshold. Open-drain output pull-ups should be selected so that the inactive-state current remains compatible with the intended battery budget.

🏭

Motor and Actuator Limit Detection

The TS339IPT can monitor travel limits, current-sense outputs, or actuator positions where a digital limit signal is more useful than an analog measurement. Four comparison channels provide compact supervision, and the open-drain outputs can pull down an enable line, interlock input, or status signal. The 3 V to 16 V supply range permits operation across low-voltage control systems and higher industrial rails, subject to each signal's common-mode limits. Place the comparator near the sensed node to minimize noise pickup, maintain a continuous low-impedance ground return, and avoid routing inputs beside motor or solenoid wiring. Pull-up resistors should be located near the receiving device when long open-drain traces would otherwise slow the rising edge.

What is the TS339IPT and what are its main specifications?
The TS339IPT is a micropower quad CMOS voltage comparator with four open-drain outputs, a 3 V to 16 V supply range, and typical consumption of 9 μA per comparator. According to the STMicroelectronics TS339 manufacturer datasheet, it also supports input voltages from ground to VCC minus 1.5 V and output sink current up to 40 mA. It is supplied in a 14-pin TSSOP package for compact surface-mount designs.
Where can I download the TS339IPT datasheet PDF?
The official TS339 manufacturer datasheet is available through the STMicroelectronics product page linked on this page. The TS339 family datasheet covers the TS339IPT electrical characteristics, pinout, application information, and package dimensions. Use the manufacturer copy for design work because third-party listings may reproduce only selected parameters or use older documentation revisions.
What is the pinout of the TS339IPT?
The TS339IPT is a 14-pin TSSOP device containing four independent comparator channels, but the exact numbered pin names are not listed on this page. Use the pin-description table and package drawing in the STMicroelectronics TS339 manufacturer datasheet when assigning PCB tracks. Do not infer the four input pairs and output pins solely from the channel count because the exposed package drawing is the authoritative assignment.
Why does every TS339IPT output need a pull-up resistor?
Each TS339IPT output is open drain, so the output transistor can pull the line low but cannot actively drive it high. The external pull-up resistor establishes the high logic level and can also be connected to a voltage different from the comparator supply. Choose the resistor to balance low output current against the required rise time and the capacitive load on each output node.
How much current does the TS339IPT consume?
The TS339IPT consumes approximately 9 μA per comparator under the manufacturer's typical operating conditions, as stated in the STMicroelectronics TS339 manufacturer datasheet. Because the device contains four comparator channels, engineers should evaluate the total device current under their actual input states, output loading, and supply voltage rather than relying only on the per-comparator typical figure.
Can TS339IPT operate from a 5 V supply?
Yes, a 5 V supply lies within the TS339IPT's stated 3 V to 16 V operating range. The manufacturer datasheet specifies an input common-mode range from 0 V to VCC minus 1.5 V, which means the upper input limit at 5 V is 3.5 V. Signals approaching the positive supply rail must be checked against that common-mode limit.
What can replace the TS339IPT without changing the PCB?
The TSX339IPT is the closest documented drop-in candidate because it is also a STMicroelectronics 14-TSSOP quad comparator with open-drain outputs. Before substitution, confirm common-mode range, propagation delay, input offset, supply current, and output-current requirements against the TS339 datasheet. Use the Request a Quote form on this page when requesting TS339IPT supply, lead time, or MOQ information.
Is TSX339IPT the same as TS339IPT?
No, TSX339IPT and TS339IPT are related STMicroelectronics quad comparator variants rather than identical parts. Both appear with 14-TSSOP packaging and open-drain outputs, but TSX339IPT is identified as a micropower 5 μA, 16 V CMOS comparator. Confirm every threshold-sensitive AC and DC parameter in the relevant manufacturer datasheet before treating it as a drop-in replacement.
What is the difference between TS339IPT and TSX339IPT?
The primary documented difference is typical supply current: TSX339IPT is described as a micropower 5 μA quad comparator, while TS339IPT is rated at 9 μA typical per comparator. Their shared 14-TSSOP package and open-drain architecture make TSX339IPT a candidate for PCB reuse, but its input common-mode limits, offset voltage, response time, and output behavior still require direct comparison.
Is TS334IPT a drop-in replacement for TS339IPT?
TS334IPT is a 14-TSSOP STMicroelectronics quad comparator with open-drain output, but it is not automatically a drop-in replacement for TS339IPT. Its listed 1.6 V to 5 V supply range differs substantially from the TS339 family's 3 V to 16 V range. The TS334IPT may fit a low-voltage design, but you must verify pin assignments, common-mode range, response time, and every operating limit before substitution.
Can TS3704IPT replace TS339IPT?
TS3704IPT is generally not a direct replacement for TS339IPT because the TS3704 family uses push-pull CMOS outputs while the TS339 uses open-drain outputs. Although both are micropower STMicroelectronics quad comparators in 14-TSSOP packages, an existing board requires a pull-up resistor for TS339 and does not require one for the push-pull TS3704. Reusing the footprint can also expose output-current and logic-polarity differences.
Where can I buy TS339IPT and check its price and lead time?
Use the Request a Quote form on this page to request TS339IPT pricing, stock confirmation, lead time, and minimum order quantity. The structured pricing data is updated separately from the technical content, while current procurement status should be confirmed through the form. The product is identified as an active part and is offered in a 14-pin TSSOP package.
How do I choose a pull-up resistor for the TS339IPT open-drain outputs?
Choose the pull-up from the required logic-high voltage, the output sink-current limit, input leakage, and total output capacitance. The STMicroelectronics TS339 manufacturer datasheet identifies a 40 mA output sink capability, so the resistor must limit current during a low output state. A larger value reduces current but slows the rising edge; a smaller value improves speed while increasing static and discharge current.
What applications are best suited to the TS339IPT?
The TS339IPT is best suited to low-power threshold detection, battery monitoring, industrial sensor interfaces, and portable equipment because it combines four channels with 9 μA typical consumption per comparator. Its open-drain outputs also support pull-ups to a selected logic voltage. The 3 V to 16 V supply range is useful for portable and industrial systems, while the −40 °C to +125 °C range supports extended-temperature equipment.
Is the TS339IPT compliant with RoHS and REACH?
The TS339IPT's RoHS and REACH status must be confirmed from the current STMicroelectronics product declaration or material-compliance documentation. A distributor listing may include a RoHS report, but that alone does not establish every declaration for the exact orderable MPN. For new production designs, request the manufacturer compliance record for TS339IPT before release to production.

کے لیے انجینئرنگ ریفرنس ڈیٹا TS339IPT — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose TS339IPT when a compact four-channel comparator is needed for 3 V to 16 V operation, low 9 μA typical consumption per channel, and open-drain outputs. It is particularly appropriate for industrial sensing, portable threshold detection, battery supervision, and fault buses that benefit from a selectable pull-up voltage. Consider TSX339IPT when lower typical current is more important and its other electrical characteristics satisfy the design. Consider TS334IPT only for low-voltage systems whose signals remain compatible with its 1.6 V to 5 V supply range. TS3704IPT can suit designs seeking push-pull outputs and no pull-up resistors, but it is not a transparent substitute for an existing open-drain TS339 circuit. For every candidate, verify numbered pin assignments, common-mode range, offset voltage, propagation delay, output current, and absolute-maximum limits before approving a drop-in change.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ TSX339IPT TS334IPT TS3704IPT
Brand STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics
Package TSSOP-14 TSSOP-14 - same TSSOP-14 - same TSSOP-14 - same
Comparator Channels 4 4 4 4
Output Type Open drain Open drain Open drain Push-pull CMOS
External Pull-Up Requirement Required on each output Required on each output Required on each output Not required for push-pull outputs

اہم امتیازی خصوصیات

  • Wider supply-voltage operating range than TS334IPT (بمقابلہTS334IPT)
  • Lower typical current than TS339IPT (بمقابلہTS339IPT)
  • Retains open-drain fault signaling (بمقابلہTS3704IPT)

ڈیزائن نوٹس

Route the four differential input pairs as short, matched traces and provide a continuous ground reference beneath the analog input region. Keep the comparator input network away from switching-power, relay, and motor traces; high-impedance CMOS inputs can respond to nearby switching edges even when the DC common-mode voltage is correct. If the sensed source is physically remote, use a shielded or protected connection and confirm that ground potential differences do not move either input outside the TS339's specified common-mode range.

Place the required pull-up resistor on every open-drain output, preferably close to the TS339IPT when trace capacitance is significant. Calculate the maximum pull-up current from the selected logic voltage and resistance, then compare it with the comparator's 40 mA output sink capability. A smaller resistor produces a faster rising edge but consumes more current while the output is low; a larger resistor reduces that consumption but can slow transitions and increase susceptibility to noise.

Do not assume that a comparator automatically provides hysteresis. Sensor noise and slow input slopes can cause repeated output transitions near the threshold, so add positive feedback or other hysteresis where appropriate. Also maintain valid signal levels during startup and shutdown: the documented upper common-mode limit is VCC minus 1.5 V, and inputs must remain within absolute-maximum ratings even while the supply is changing. Verify the pull-up voltage separately from the TS339 supply voltage.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The exact orderable MPN's compliance declarations were not established by the manufacturer information included for this product. Obtain the current STMicroelectronics material-compliance documentation before production release.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-16 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

TS339IPT datasheet TS339IPT pinout TS339IPT datasheet pdf TS339IPT equivalent TS339IPT replacement TS339IPT cross reference TS339IPT vs TSX339IPT TS339IPT TSSOP-14 footprint TS339IPT application circuit TS339IPT price TS339IPT stock STMicroelectronics TS339IPT

متعلقہ اجزاء اور اصطلاحات

STMicroelectronics TS339IPT TSX339IPT TS334IPT TS3704IPT voltage comparator quad comparator comparator IC analog integrated circuit semiconductor CMOS open-drain output push-pull CMOS output micro-power electronics supply current input common-mode range propagation delay input offset voltage battery monitoring industrial sensor interface overvoltage detection TSSOP-14 TSSOP package family surface-mount package pull-up resistor
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں