TS339IPT - Micropower Quad Open-Drain Comparator | ST
料号: TS339IPT ✓ 量产中TS339IPT 概述
A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input exceeds the inverting input. The TS339 belongs to the comparator hierarchy, combining four independent comparator channels with CMOS input stages and open-drain outputs. The TS339 family provides a practical alternative to higher-current bipolar LM339-family comparators in battery-powered and portable equipment.
Key features include four comparator channels, a typical input common-mode range extending from ground to VCC minus 1.5 V, an output sink capability of 40 mA, and open-drain outputs that can be pulled up to a chosen external voltage. The low 9 μA typical current per comparator supports low-power sensing, while the 16 V maximum supply rating permits operation from a 3 V supply through higher-voltage industrial rails. These characteristics make the device suitable for threshold detection, battery monitoring, signal conditioning, and sensor interfaces.
The open-drain architecture provides flexible output voltage levels but requires an external pull-up resistor on every output. The pull-up resistor establishes the high output level, while the output transistor actively pulls the line toward ground. This arrangement permits wired logic, level translation, and wired-AND behavior, although designers must account for the rise time created by the resistor and total bus capacitance. Input common-mode and output-level requirements must be checked against the actual supply voltage.
Typical applications include portable battery monitoring, industrial sensor interfaces, window or level comparators, overvoltage detection, and low-power control systems. Because the TS339IPT is specified for the industrial temperature range, it can also be used in equipment exposed to temperatures from −40 °C to +125 °C. The 14-pin TSSOP package supports compact, surface-mount assembly but is relatively narrow and requires careful component placement.
When designing a PCB around the TS339IPT, route the comparator inputs away from switching nodes and provide a short, quiet ground reference for each sensing point. Place pull-up resistors close to the corresponding open-drain outputs to minimize trace capacitance and improve switching speed. Confirm that the logic high generated by the pull-up meets the receiving device's input threshold, and verify that no signal connected to either comparator input exceeds the datasheet's absolute maximum ratings.
This page combines the TS339IPT's principal electrical characteristics, verified package and distributor information, application guidance, comparison data, and practical replacement considerations to support faster component selection and board-level design.
直接替换替代料: TS339IPT ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
TSX339IPT
✅ 直接替换📋 参考替代料(不在目录中)
TS334IPT
✅ 直接替换📋 参考替代料(不在目录中)
TS3704IPT
✅ 直接替换📋 参考替代料(不在目录中)
TS339IPT 最大额定值与电气特性
| Comparator Type | 4-channel general-purpose voltage comparator |
| Technology | CMOS |
| 输出类型 | Open drain |
| Number of Channels | 4 channels |
| Supply Voltage Range | 3 V to 16 V |
| Typical Supply Current | 9 μA per comparator |
| Input Common-Mode Range | 0 V to VCC − 1.5 V |
| Output Sink Current | 40 mA |
| 工作温度范围 | −40 °C to +125 °C |
| 封装 | TSSOP-14 |
| 安装类型 | Surface mount |
TS339IPT tssop-14 引脚配置指南
TS339IPT(tssop-14 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: TS339IPT.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TS339IPT 适用于 6 应用s: Portable Battery Monitoring, Industrial Sensor Threshold Detection, Overvoltage and Power Rail Detection, Window and Level Comparators, Battery-Powered Environmental Sensing, Motor and Actuator Limit Detection.
Portable Battery Monitoring
The TS339IPT is suitable for monitoring battery-derived rails in portable instruments because four independent comparator channels can support multiple threshold checks without requiring four separate packages. Its typical 9 μA per-comparator consumption is well suited to low-power sensing, while the 3 V to 16 V supply range accommodates common single-cell and industrial battery systems. Each open-drain output can pull up to a selected system logic level through an external resistor, allowing a microcontroller input to remain compatible even when the comparator operates from a different rail. The design should account for the upper common-mode limit of VCC minus 1.5 V and choose pull-up values that balance battery consumption against switching speed.
推荐
Industrial Sensor Threshold Detection
The TS339IPT fits industrial sensor interfaces that convert an analog measurement into a switching event, such as pressure, temperature, or level sensing. Four channels provide independent comparisons, while 9 μA typical current per comparator reduces the load imposed by always-on sensing circuitry. The industrial temperature range of −40 °C to +125 °C supports equipment operating across demanding ambient conditions. Designers should place input traces away from motors, relays, and switching-power nodes, then reference each comparator input to a quiet ground region. Open-drain outputs simplify wired alarm or fault signaling when each line receives a pull-up to the appropriate control-logic voltage.
推荐
Overvoltage and Power Rail Detection
The TS339IPT can supervise multiple power rails by comparing divided input voltages against precise references. Its operating supply range of 3 V to 16 V allows the comparator itself to operate across common industrial voltage levels, and its open-drain output can directly pull down a fault line or alert signal. The comparator's input common-mode ceiling of VCC minus 1.5 V means divider and reference design must keep both inputs inside the valid range, including during fault conditions. A pull-up resistor is required on every fault output. This arrangement is useful for battery packs, external power modules, and board-level protection where an open-drain fault bus provides a simple wired fault indication.
推荐
Window and Level Comparators
The TS339IPT is appropriate for implementing upper and lower window limits, tank-level detection, or simple mechanical position sensing. Two channels can establish the lower and upper thresholds around a reference, while the other channels can monitor additional sensor points. The quad architecture reduces package count compared with discrete single comparators and preserves the low 9 μA typical per-channel current. For slowly changing sensor signals, add suitable hysteresis to prevent output chatter around the threshold. Because the outputs are open drain, pull-ups can be tied to the receiving system's logic rail, and multiple fault conditions can be combined into a common wired-alert line where the circuit architecture permits it.
推荐
Battery-Powered Environmental Sensing
The TS339IPT can support low-duty-cycle environmental sensing systems that compare thermistor, light, or humidity-sensor outputs against preset limits. Its four channels allow several alarms to be evaluated locally without waking a main controller for every measurement, while the low typical supply current helps preserve battery life. The 3 V minimum supply supports low-voltage sensor nodes, and the 16 V maximum rating provides margin for protected industrial installations. Keep comparator inputs short and use a quiet analog ground because switching activity and long sensor traces can shift the apparent threshold. Open-drain output pull-ups should be selected so that the inactive-state current remains compatible with the intended battery budget.
推荐
Motor and Actuator Limit Detection
The TS339IPT can monitor travel limits, current-sense outputs, or actuator positions where a digital limit signal is more useful than an analog measurement. Four comparison channels provide compact supervision, and the open-drain outputs can pull down an enable line, interlock input, or status signal. The 3 V to 16 V supply range permits operation across low-voltage control systems and higher industrial rails, subject to each signal's common-mode limits. Place the comparator near the sensed node to minimize noise pickup, maintain a continuous low-impedance ground return, and avoid routing inputs beside motor or solenoid wiring. Pull-up resistors should be located near the receiving device when long open-drain traces would otherwise slow the rising edge.
推荐
推荐产品汇总
工程参考数据: TS339IPT ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TSX339IPT | TS334IPT | TS3704IPT |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | TSSOP-14 | TSSOP-14 - same | TSSOP-14 - same | TSSOP-14 - same |
| Comparator Channels | 4 | 4 | 4 | 4 |
| Output Type | Open drain | Open drain | Open drain | Push-pull CMOS |
| External Pull-Up Requirement | Required on each output | Required on each output | Required on each output | Not required for push-pull outputs |
关键差异点
- Wider supply-voltage operating range than TS334IPT (对比 TS334IPT)
- Lower typical current than TS339IPT (对比 TS339IPT)
- Retains open-drain fault signaling (对比 TS3704IPT)
设计说明
Route the four differential input pairs as short, matched traces and provide a continuous ground reference beneath the analog input region. Keep the comparator input network away from switching-power, relay, and motor traces; high-impedance CMOS inputs can respond to nearby switching edges even when the DC common-mode voltage is correct. If the sensed source is physically remote, use a shielded or protected connection and confirm that ground potential differences do not move either input outside the TS339's specified common-mode range.
Place the required pull-up resistor on every open-drain output, preferably close to the TS339IPT when trace capacitance is significant. Calculate the maximum pull-up current from the selected logic voltage and resistance, then compare it with the comparator's 40 mA output sink capability. A smaller resistor produces a faster rising edge but consumes more current while the output is low; a larger resistor reduces that consumption but can slow transitions and increase susceptibility to noise.
Do not assume that a comparator automatically provides hysteresis. Sensor noise and slow input slopes can cause repeated output transitions near the threshold, so add positive feedback or other hysteresis where appropriate. Also maintain valid signal levels during startup and shutdown: the documented upper common-mode limit is VCC minus 1.5 V, and inputs must remain within absolute-maximum ratings even while the supply is changing. Verify the pull-up voltage separately from the TS339 supply voltage.
合规信息
The exact orderable MPN's compliance declarations were not established by the manufacturer information included for this product. Obtain the current STMicroelectronics material-compliance documentation before production release.