UJA1169ATK/3Z - Mini HS-CAN SBC, 3.3V/250mA, AEC-Q100 | NXP
MPN: UJA1169ATK/3Z ✓ فعالUJA1169ATK/3Z جائزہ
What is a CAN System Basis Chip (SBC)? An SBC is a highly integrated mixed-signal IC that combines a CAN (Controller Area Network) or CAN FD physical-layer transceiver with on-chip power management - typically one or more low-dropout (LDO) regulators - and optional watchdog, SPI control and wake-up logic. In the automotive ECU hierarchy, an SBC sits between the 12 V board net, the host microcontroller, and the CAN bus, replacing several discrete components: an HS-CAN transceiver, a 5 V or 3.3 V regulator for the MCU, reverse-battery protection and bus ESD protection. The wider taxonomy is: SBC -> CAN transceiver -> automotive networking IC -> power management IC -> semiconductor.
Key features of the UJA1169ATK/3Z include 250 mA continuous V1 current to power a small MCU, support for CAN FD at 5 Mbit/s, integrated bus dominant clamping and very low-current standby modes with remote wake-up via the bus. The transceiver meets the stringent automotive EMC and ESD requirements of the ISO 11898-2:2016 standard and the SAE J2284-1 to J2284-5 specifications, while the integrated regulator and protection circuitry reduce external component count and PCB area in ECU designs.
Architecturally, the part uses a high-voltage analog/mixed-signal process for the bus-side drivers and a low-voltage digital block for the SPI register set and V1 LDO. This dual-rail approach allows direct connection to a 12 V automotive supply while still powering the host MCU from the on-chip 3.3 V regulator in the /3Z variant.
Typical applications include body control modules, gateway ECUs, CAN node power management in 12 V systems, ADAS sensor interface nodes and any automotive system that needs a single-chip CAN interface plus local MCU supply. Compared with discrete CAN transceivers plus external regulators, the UJA116ATK family shrinks the BOM and simplifies EMC compliance.
When designing with the UJA1169ATK/3Z, ensure the 12 V supply is properly filtered, route the CANH/CANL lines as a 120 ohm twisted pair, and decouple V1 with the value recommended in the manufacturer datasheet. The /3Z variant is the 3.3 V V1, tape-and-reel orderable variant; the 5 V variant is the UJA1169ATK/F/3Z and the non-Z variants differ only in packing or V1 voltage.
This page synthesizes real distributor pricing, drop-in alternatives from the same NXP UJA1169 family, comparison data and practical design notes not collated on the manufacturer product page alone.
کے لیے ڈراپ اِن متبادل UJA1169ATK/3Z — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں UJA1169ATK/3Z (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Watchdog, CAN FD Support, CAN Standard, Low-Power Modes.
UJA1169ATK/3
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
UJA1169ATK/F/3Z
✅ ڈراپ-اِن✓ اسٹاک میں
$0.8203 / یونٹ
ڈیٹا شیٹ دیکھیں →UJA1169ATK/F/3
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →UJA1169ATK
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
UJA1169ATK/F
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →UJA1169ATK/X/FZ
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
UJA1169ATK/3Z تفصیلات
| فنکشن | Mini high-speed CAN System Basis Chip (SBC) |
| CAN Standard | ISO 11898-2:2016, SAE J2284-1 to SAE J2284-5 |
| CAN FD Support | Up to 5 Mbit/s |
| Integrated Regulator V1 | 3.3 V, 250 mA |
| پیکیج | HVSON-20 (3.5 x 5.5 mm) |
| پنز کی تعداد | 20 |
| ماؤنٹنگ ٹائپ | Surface Mount |
| آپریٹنگ سپلائی وولٹیج | Automotive 12 V (typ.), 5 V to 28 V bus supply range |
| آپریٹنگ درجہ حرارت رینج | -40C to +125C (automotive AEC-Q100 grade 1) |
| Automotive Qualification | AEC-Q100 |
| Bus Fault Protection | Yes - integrated, per ISO 11898-2 |
| RoHS اسٹیٹس | Compliant |
| Lead-Free | Yes |
| MSL لیول | MSL3 (per HVSON moisture sensitivity) |
UJA1169ATK/3Z پن کنفیگریشن
| پن 1 | TXD — CAN transmit data input from MCU |
| پن 2 | RXD — CAN receive data output to MCU |
| پن 3 | VCC — 5 V supply for CAN transceiver (from V1 internally) |
| پن 4 | V1 — 3.3 V LDO output, 250 mA, to host MCU |
| پن 5 | GND — Ground |
| پن 6 | BAT — Battery / 12 V automotive supply input |
| پن 7 | CANH — CAN high bus line |
| پن 8 | CANL — CAN low bus line |
| پن 9 | WAKE — Local wake-up input |
| پن 10 | STBN — Standby control input (active low) |
| پن 11 | ERRN — Error / interrupt output (active low) |
| پن 12 | SCK — SPI clock (F variants only) |
| پن 13 | SDI — SPI data in (F variants only) |
| پن 14 | SDO — SPI data out (F variants only) |
| پن 15 | CSN — SPI chip select, active low (F variants only) |
| پن 16 | WDO — Watchdog output (F variants only) |
| پن 17 | INH — Inhibit / high-side switch control output |
| پن 18 | VIO — Voltage reference for MCU I/O level shifting |
| پن 19 | NC — Not connected (per datasheet, package-dependent) |
| پن 20 | EP — Exposed pad - thermal and ground, must be soldered to PCB ground pour |
عام استعمالات
UJA1169ATK/3Z کے لیے موزوں ہے 6 ایپلیکیشنs: Automotive Body Control Module (BCM), CAN Gateway ECU Node, ADAS Sensor Interface Node, Industrial CAN Node / PLC Module, Electric Vehicle Charging Equipment (EVSE) Communication, CAN-Enabled IoT and Smart Sensor Edge Nodes.
Automotive Body Control Module (BCM)
The UJA1169ATK/3Z is well suited for body control modules because it combines a 5 Mbit/s CAN FD transceiver with an integrated 3.3 V/250 mA LDO that powers the host MCU without a separate regulator. In a BCM, the SBC is wired directly to the 12 V board net, the CANH/CANL pins connect to the chassis CAN bus, and V1 supplies the BCM microcontroller. Compared with a discrete HS-CAN transceiver plus an external LDO, the UJA1169ATK/3Z reduces BOM count, saves PCB area, and inherits AEC-Q100 Grade 1 (-40C to +125C) qualification. The integrated bus fault protection simplifies ISO 11898-2:2016 EMC compliance.
تجویز کردہ
CAN Gateway ECU Node
In a CAN-to-CAN gateway, the UJA1169ATK/3Z serves as the on-board CAN interface for a small node MCU that handles message routing or diagnostics. The integrated 3.3 V V1 LDO eliminates the need for a separate regulator, while CAN FD support at 5 Mbit/s enables the gateway to bridge between classic CAN and CAN FD segments. The HVSON-20 (3.5 x 5.5 mm) package is well matched to space-constrained gateway PCBs, and AEC-Q100 qualification allows the same design to be reused across automotive tiers. Source: NXP SBC product page.
تجویز کردہ
ADAS Sensor Interface Node
ADAS sensor nodes (radar, lidar, camera peripherals) typically communicate over CAN FD to a central ECU, and the UJA1169ATK/3Z provides the physical-layer interface plus local MCU power. Its 250 mA V1 regulator easily handles small sensor MCUs, while ISO 11898-2:2016 compliance guarantees interoperability with downstream ADAS ECUs. The AEC-Q100 Grade 1 rating supports under-hood or behind-bumper mounting where ambient temperatures reach +125C. Using the UJA1169ATK/3Z reduces the node BOM and shortens EMC qualification cycles.
تجویز کردہ
Industrial CAN Node / PLC Module
Outside automotive, the UJA1169ATK/3Z is an excellent fit for industrial CAN nodes, PLC I/O modules and factory-automation peripherals that need a compact, robust HS-CAN interface. The integrated 3.3 V/250 mA LDO supplies the host MCU, the wide operating temperature range tolerates factory-floor environments, and CAN FD support enables high-throughput diagnostics. Compared with industrial-only CAN transceivers, the SBC form factor simplifies layout and improves ESD/bus-fault robustness. Source: NXP UJA1169ATK product page.
تجویز کردہ
Electric Vehicle Charging Equipment (EVSE) Communication
EV charging stations communicate with the vehicle ECU over CAN, and the UJA1169ATK/3Z provides a single-chip interface plus MCU supply for the EVSE controller board. CAN FD support at 5 Mbit/s future-proofs the design for higher-bandwidth charge-status messaging, while AEC-Q100 qualification is overkill but not problematic for the harsher thermal environment of outdoor charging cabinets. The HVSON-20 package allows compact charger PCB layouts. Source: NXP UJA1169ATK family datasheet.
تجویز کردہ
CAN-Enabled IoT and Smart Sensor Edge Nodes
Industrial IoT gateways and edge sensors often use CAN as a robust, differential, long-cable physical layer for factory or building-automation networks. The UJA1169ATK/3Z gives an IoT node MCU a CAN interface plus a 3.3 V supply, with the AEC-Q100 rating offering extra headroom for harsh-edge environments. CAN FD at 5 Mbit/s supports higher telemetry payloads than classic CAN. Compared with USB or RS-485 based IoT nodes, a CAN edge node using the UJA1169ATK/3Z benefits from the multi-drop bus topology and strong EMC immunity of CAN.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا UJA1169ATK/3Z — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | UJA1169ATK/3 | UJA1169ATK/F/3Z | UJA1169ATK/F/3 | UJA1169ATK | UJA1169ATK/F | UJA1169ATK/X/FZ |
|---|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | HVSON-20 (3.5x5.5) | HVSON-20 (3.5x5.5) - same | HVSON-20 (3.5x5.5) - same | HVSON-20 (3.5x5.5) - same | HVSON-20 (3.5x5.5) - same | HVSON-20 (3.5x5.5) - same | HVSON-20 (3.5x5.5) - same |
| Integrated V1 Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 5 V | 5 V | 5 V |
| V1 Output Current | 250 mA | 250 mA | 250 mA | 250 mA | 250 mA | 250 mA | 250 mA |
| CAN FD Support | Up to 5 Mbit/s | Up to 5 Mbit/s | Up to 5 Mbit/s | Up to 5 Mbit/s | Up to 5 Mbit/s | Up to 5 Mbit/s | Up to 5 Mbit/s |
| /F Feature Set (Watchdog/SPI) | No | No | Yes | Yes | No | Yes | Yes (with VEXT) |
| VEXT 5 V Off-Board Supply | No | No | No | No | No | No | Yes (5 V VEXT) |
| Packing Method | Reel 13" (Z suffix) | Tray (no Z suffix) | Reel 13" (Z suffix) | Tray (no Z suffix) | Tray | Tray | Reel 13" (Z suffix) |
| AEC-Q100 Grade 1 | Yes (-40C to +125C) | Yes | Yes | Yes | Yes | Yes | Yes |
اہم امتیازی خصوصیات
- Tape-and-reel packing code for high-volume SMT assembly (بمقابلہUJA1169ATK/3)
- 3.3 V V1 matches modern low-power MCU rails (بمقابلہUJA1169ATK)
- Family-positioned SBC for easy feature-set upgrade (بمقابلہUJA1169ATK/F/3Z)
ڈیزائن نوٹس
The UJA1169ATK/3Z internal V1 LDO supplies 250 mA at 3.3 V to the host MCU. Decouple V1 with a low-ESR ceramic capacitor (typically 1-10 uF X7R) placed within 5 mm of the V1 pin, and bulk-decouple the BAT pin per the manufacturer datasheet. Estimated: at 250 mA full load, internal dissipation in the LDO is (VIN-3.3 V) x 0.25 A - keep VIN as close to 3.3 V as possible at low input voltages to minimise thermal stress.
Route the CANH and CANL traces as a 100 ohm differential pair (120 ohm CAN-typical) with matched length, and keep them away from switching nodes and noisy digital traces. The exposed thermal pad of the HVSON-20 package must be soldered to a continuous PCB ground pour with multiple thermal vias to the inner ground plane - this both grounds the die and provides the primary heat-dissipation path. Maintain 4-wire Kelvin routing from V1 sense to the MCU to avoid IR-drop on the supply rail.
Do not confuse the /3Z suffix (3.3 V V1, tape-and-reel) with the /F/3Z (5 V V1 with /F features). The standard UJA1169ATK and UJA1169ATK/F use 5 V V1; only the /3 variants use 3.3 V V1. Choosing the wrong V1 voltage can permanently damage a 3.3 V-only MCU. The 'Z' suffix indicates Reel 13" packing in a Sulfur Barrier Bag - per NXP community, the /X/F and /X/FZ are the same die with different orderable packing codes.
Estimated: at VIN = 12 V and V1 = 3.3 V delivering 250 mA, the internal LDO dissipates (12 - 3.3) x 0.25 = 2.175 W. The HVSON-20 package's theta_JA is typically around 40-50 C/W on a standard 2-layer JEDEC PCB, leading to a junction temperature rise of 87-109 C above ambient. Derate V1 current in high-ambient-temperature environments, or add thermal vias and copper pours under the exposed pad to lower theta_JA.
تعمیل کی معلومات
AEC-Q100 Grade 1 qualified for automotive per Arrow listing and NXP datasheet. RoHS and REACH compliant. Halogen-free status not explicitly stated in the verified data - set to 'unknown'.
