ISPLSI 1032-60LT - 128-Macrocell 5V CPLD, 60MHz, TQFP-100 | Lattice
MPN: 1032-60LT ✗ Cuối đời1032-60LT Tóm tắt
What is a CPLD? A Complex Programmable Logic Device is a non-volatile programmable logic IC that sits between simple SPLDs/PLAs and large FPGAs in the programmable-logic taxonomy (CPLD -> PLD -> programmable logic -> digital semiconductor). It uses a small-block, sum-of-products architecture with macrocells, making it ideal for implementing wide combinational and registered logic, glue logic, bus decoding, state machines, and address decoding. Unlike SRAM FPGAs, the ispLSI 1032 is non-volatile and in-system programmable via a standard 5-pin JTAG chain, so designs can be updated on production hardware without removing the device.
Key features of the ISPLSI 1032-60LT include 32 logic elements (each containing 16 macrocells with associated I/O), 6000 gates of usable logic, 4 dedicated clock inputs feeding four global clock buffers, asynchronous clear and preset per register, JTAG/IEEE 1149.1 boundary-scan test support, and 5 V CMOS I/O with TTL-compatible thresholds. The GRP provides a deterministic, fixed interconnect delay regardless of placement, simplifying timing closure for registered and combinatorial logic.
Typical applications include wide address decoding, bus interface glue logic, state-machine controllers, peripheral interface latching, fast counters, frequency and pulse-width measurement, and any design requiring non-volatile, deterministic-timing 5 V glue logic in industrial control, telecom backplane, and embedded processor bus systems.
When designing with this device, ensure the 5 V supply is within the 4.75 V to 5.25 V range and that all I/O banks are referenced to a single 5 V rail. Decouple VCC with 0.1 uF and 10 uF capacitors close to the pins. Note that Lattice's own ispMACH 4000V is the recommended modern replacement family for new designs.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Bộ thay thế dễ dàng lắp đặt cho 1032-60LT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
ISPLSI 1032-70LT
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ISPLSI 1032-60L
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
LC4128V-75T100
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LC4064V-75T100
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATF1508AS-10AU100
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
XC95108XL-10TQ100
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
1032-60LT Tỷ lệ tối đa & tính chất điện
| Product Type | CPLD (Complex Programmable Logic Device) |
| Family | ispLSI 1000 |
| Number of Macrocells | 128 |
| Number of Logic Elements/Blocks | 32 |
| Number of Gates | 6000 PLD gates |
| Number of Registers | 192 |
| Number of Universal I/O Pins | 64 |
| Number of Dedicated Input Pins | 8 |
| Number of Dedicated Clock Input Pins | 4 |
| Maximum Propagation Delay (tpd) | 20 ns |
| Maximum Operating Frequency (fMAX) | 60 MHz |
| Supply Voltage (VCC) | 4.75 V to 5.25 V |
| Programmable Type | In-System Programmable (ISP) / JTAG |
| Hộp | 100-pin TQFP |
| Kiểu lắp đặt | Surface Mount |
| JTAG / Boundary Scan | IEEE 1149.1 compliant |
Cấu hình chân 1032-60LT
| Chân 1 | GND — Ground |
| Chân 2 | Y4/RESET — Dedicated clock input or global reset |
| Chân 3 | I/O — Universal I/O pin (group A) |
| Chân 4 | I/O — Universal I/O pin (group A) |
| Chân 5 | I/O — Universal I/O pin (group A) |
| Chân 6 | I/O — Universal I/O pin (group A) |
| Chân 7 | I/O — Universal I/O pin (group A) |
| Chân 8 | I/O — Universal I/O pin (group A) |
| Chân 9 | I/O — Universal I/O pin (group A) |
| Chân 10 | I/O — Universal I/O pin (group A) |
| Chân 11 | GND — Ground |
| Chân 12 | VCC — +5 V supply |
| Chân 13 | I/O — Universal I/O pin (group B) |
| Chân 14 | I/O — Universal I/O pin (group B) |
| Chân 15 | I/O — Universal I/O pin (group B) |
| Chân 16 | I/O — Universal I/O pin (group B) |
| Chân 17 | I/O — Universal I/O pin (group B) |
| Chân 18 | I/O — Universal I/O pin (group B) |
| Chân 19 | I/O — Universal I/O pin (group B) |
| Chân 20 | I/O — Universal I/O pin (group B) |
| Chân 21 | GND — Ground |
| Chân 22 | VCC — +5 V supply |
| Chân 23 | I/O — Universal I/O pin (group C) |
| Chân 24 | I/O — Universal I/O pin (group C) |
| Chân 25 | I/O — Universal I/O pin (group C) |
| Chân 26 | I/O — Universal I/O pin (group C) |
| Chân 27 | I/O — Universal I/O pin (group C) |
| Chân 28 | I/O — Universal I/O pin (group C) |
| Chân 29 | I/O — Universal I/O pin (group C) |
| Chân 30 | I/O — Universal I/O pin (group C) |
| Chân 31 | GND — Ground |
| Chân 32 | VCC — +5 V supply |
| Chân 33 | I/O — Universal I/O pin (group D) |
| Chân 34 | I/O — Universal I/O pin (group D) |
| Chân 35 | I/O — Universal I/O pin (group D) |
| Chân 36 | I/O — Universal I/O pin (group D) |
| Chân 37 | I/O — Universal I/O pin (group D) |
| Chân 38 | I/O — Universal I/O pin (group D) |
| Chân 39 | I/O — Universal I/O pin (group D) |
| Chân 40 | I/O — Universal I/O pin (group D) |
| Chân 41 | GND — Ground |
| Chân 42 | VCC — +5 V supply |
| Chân 43 | Y0 — Dedicated clock input 0 |
| Chân 44 | Y1 — Dedicated clock input 1 |
| Chân 45 | Y2 — Dedicated clock input 2 |
| Chân 46 | Y3 — Dedicated clock input 3 |
| Chân 47 | IN0 — Dedicated input 0 |
| Chân 48 | IN1 — Dedicated input 1 |
| Chân 49 | IN2 — Dedicated input 2 |
| Chân 50 | IN3 — Dedicated input 3 |
| Chân 51 | GND — Ground |
| Chân 52 | VCC — +5 V supply |
| Chân 53 | TDI — JTAG test data input |
| Chân 54 | TMS — JTAG test mode select |
| Chân 55 | TCK — JTAG test clock |
| Chân 56 | TDO — JTAG test data output |
| Chân 57 | NC — Not connected (per datasheet) |
| Chân 58 | I/O — Universal I/O pin (group E) |
| Chân 59 | I/O — Universal I/O pin (group E) |
| Chân 60 | I/O — Universal I/O pin (group E) |
| Chân 61 | I/O — Universal I/O pin (group E) |
| Chân 62 | GND — Ground |
| Chân 63 | VCC — +5 V supply |
| Chân 64 | I/O — Universal I/O pin (group E) |
| Chân 65 | I/O — Universal I/O pin (group E) |
| Chân 66 | I/O — Universal I/O pin (group E) |
| Chân 67 | I/O — Universal I/O pin (group E) |
| Chân 68 | I/O — Universal I/O pin (group F) |
| Chân 69 | I/O — Universal I/O pin (group F) |
| Chân 70 | I/O — Universal I/O pin (group F) |
| Chân 71 | I/O — Universal I/O pin (group F) |
| Chân 72 | GND — Ground |
| Chân 73 | VCC — +5 V supply |
| Chân 74 | I/O — Universal I/O pin (group F) |
| Chân 75 | I/O — Universal I/O pin (group F) |
| Chân 76 | I/O — Universal I/O pin (group F) |
| Chân 77 | I/O — Universal I/O pin (group F) |
| Chân 78 | I/O — Universal I/O pin (group G) |
| Chân 79 | I/O — Universal I/O pin (group G) |
| Chân 80 | I/O — Universal I/O pin (group G) |
| Chân 81 | I/O — Universal I/O pin (group G) |
| Chân 82 | GND — Ground |
| Chân 83 | VCC — +5 V supply |
| Chân 84 | I/O — Universal I/O pin (group G) |
| Chân 85 | I/O — Universal I/O pin (group G) |
| Chân 86 | I/O — Universal I/O pin (group G) |
| Chân 87 | I/O — Universal I/O pin (group G) |
| Chân 88 | I/O — Universal I/O pin (group H) |
| Chân 89 | I/O — Universal I/O pin (group H) |
| Chân 90 | I/O — Universal I/O pin (group H) |
| Chân 91 | I/O — Universal I/O pin (group H) |
| Chân 92 | GND — Ground |
| Chân 93 | VCC — +5 V supply |
| Chân 94 | I/O — Universal I/O pin (group H) |
| Chân 95 | I/O — Universal I/O pin (group H) |
| Chân 96 | I/O — Universal I/O pin (group H) |
| Chân 97 | I/O — Universal I/O pin (group H) |
| Chân 98 | I/O — Universal I/O pin (group H) |
| Chân 99 | I/O — Universal I/O pin (group H) |
| Chân 100 | I/O — Universal I/O pin (group H) |
Ứng dụng tiêu biểu
1032-60LT phù hợp cho 6 Áp dụngs: Wide Address Decoding in Embedded Systems, Bus Interface Glue Logic, State Machine Controllers, Fast Counters and Frequency Measurement, Peripheral Interface Latching and Timing, Industrial Control and Backplane Logic.
Wide Address Decoding in Embedded Systems
The ISPLSI 1032-60LT is well suited to wide address decoding in 16/32-bit embedded processor systems where multiple peripherals share the bus. The 128 macrocells easily handle chip-select decoding for memories, peripherals, and bus buffers, while the 64 I/O provide enough pins to decode full 24-bit or 26-bit address spaces. The 20 ns propagation delay adds minimal wait-state overhead at 60 MHz system clocks, and JTAG ISP allows last-minute board redefinition. Placed between the processor and memory bus, the device replaces dozens of 74-series decoders with a single non-volatile part that survives power cycles without reload.
Được đề xuất
Bus Interface Glue Logic
For board-level glue logic between microprocessors, DSPs, ASICs, and bus transceivers, the ISPLSI 1032-60LT consolidates multiple 74-series logic functions into one programmable part. The 6000 gates and 192 registers handle data-bus multiplexing, handshaking, and protocol translation in a single device. Its 5 V tolerance matches TTL/CMOS peripherals, while JTAG ISP enables post-incident iteration to fix logic bugs without respinning the PCB. The non-volatile configuration means no boot PROM is required, simplifying the BOM and shortening the bring-up cycle.
Được đề xuất
State Machine Controllers
The ISPLSI 1032-60LT implements complex state machines, sequencers, and protocol controllers that would otherwise require a microcontroller. Wide input gating (16-product-term macrocells with shared expanders) and the deterministic GRP interconnect make timing closure straightforward even for 8- or 16-state machines. Typical uses are industrial controller sequencers, motor drive state machine, and protocol controllers in telecom backplanes. The 60 MHz fMAX grade handles real-time state transitions at typical 10-25 MHz state-machine clock rates, leaving margin for synchronous I/O. The JTAG boundary scan aids board-level test of the state machine I/O.
Được đề xuất
Fast Counters and Frequency Measurement
The ISPLSI 1032-60LT serves as a fast counter, period/frequency counter, or pulse-width measurement engine. The 4 dedicated clock inputs feed four global clock buffers that can drive counters synchronously, while the 192 registers accommodate multi-stage ripple or synchronous counters up to 24 bits. The 60 MHz fMAX grade handles direct frequency counting up to 60 MHz without prescaling, and wide input gating allows combining counters with comparators and decoders in the same device. Used in instrumentation, telecom line cards, and motor speed measurement.
Được đề xuất
Peripheral Interface Latching and Timing
For latching data from high-speed peripherals such as parallel ADCs, DACs, or LVDS interfaces, the ISPLSI 1032-60LT provides 64 I/O with deterministic 20 ns tpd and 192 registers for multi-byte data pipelines. The GRP simplifies timing closure by giving every registered output the same clock-to-output skew, ideal for source-synchronous interfaces. JTAG boundary scan simplifies board-level test of all 64 I/O, which is critical in dense surface-mount designs where traditional test points are inaccessible.
Được đề xuất
Industrial Control and Backplane Logic
In industrial control cabinets, motor drive backplanes, and telecom line cards, the ISPLSI 1032-60LT implements the deterministic 5 V logic glue between processors, drivers, and bus transceivers. Its 5 V supply, 64 I/O, and 192 registers handle optocoupler inputs, relay drivers, encoder/encoder contacts, and serial communication. The deterministic GRP timing supports hard real-time control loops at 1-10 kHz with deterministic latencies, which is essential in safety-critical and motor control systems. The non-volatile EEPROM configuration survives brown-outs without boot PROMs.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho 1032-60LT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ISPLSI 1032-70LT | ISPLSI 1032-60L | LC4128V-75T100 | LC4064V-75T100 | ATF1508AS-10AU100 | XC95108XL-10TQ100 |
|---|---|---|---|---|---|---|---|
| Brand | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Microchip Technology | Xilinx |
| Package | TQFP-100 | TQFP-100 | TQFP-100 | TQFP-100 | TQFP-100 | TQFP-100 | TQFP-100 |
| Macrocells | 128 | 128 | 128 | 128 | 64 | 128 | 108 |
| Propagation Delay (tpd) | 20 ns | 15 ns | 20 ns | 7.5 ns | 7.5 ns | 10 ns | 10 ns |
| Supply Voltage | 5 V (4.75 V - 5.25 V) | 5 V (4.75 V - 5.25 V) | 5 V (4.75 V - 5.25 V) | 3.3 V (3.0 V - 3.6 V) / 5 V tolerant | 3.3 V (3.0 V - 3.6 V) / 5 V tolerant | 5 V (4.75 V - 5.25 V) | 3.3 V (3.0 V - 3.6 V) / 5 V tolerant |
| In-System Programmable (ISP) | Yes (JTAG IEEE 1149.1) | Yes (JTAG) | Yes (JTAG) | Yes (JTAG) | Yes (JTAG) | Yes (JTAG) | Yes (JTAG) |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Active | Active | Active | Obsolete |
Bảo phân biệt quan trọng
- Non-volatile EEPROM configuration - no boot PROM required (vsSRAM FPGAs in the same gate-count class)
- Deterministic GRP timing - no placement-dependent delays (vsXC95108XL-10TQFP-100 (Xilinx))
- 5 V native supply - direct interface to TTL/CMOS peripherals (vsLC4128V-75T100 (Lattice ispMACH 4000V))
Ghi chú thiết kế
Power the ISPLSI 1032-60LT from a 5 V rail regulated within 4.75 V to 5.25 V; per Lattice datasheet, operation outside this range is not guaranteed. Decouple each VCC pin with a 0.1 uF ceramic capacitor and provide at least one 10 uF bulk capacitor near the device. ISP programming requires stable VCC during the programming cycle, so avoid large inrush loads on the same rail during programming.
Route JTAG signals (TDI, TMS, TCK, TDO) as a daisy chain from the connector to all JTAG devices on the board, with 10 kohm pull-ups on TDI/TMS/TCK to VCC. Keep JTAG traces short and away from clock signals to reduce noise. Use at least four via-stitched ground connections around the TQFP-100 footprint for thermal and EMI performance, since the 1032 dissipates roughly 1.5 W worst case.
Do not exceed 5.25 V on any pin or damage will occur to the CMOS I/O cells. When migrating to the ispMACH 4000V replacement family (LC4128V or LC4064V), confirm pinout against the Lattice migration guide - although TQFP-100 is shared, the VCC and GND pin assignments may differ slightly. Ensure unused I/O pins are left floating or driven to a defined state; do not tie them directly to VCC or GND.
Estimated: With all 64 outputs toggling at 60 MHz into 50 pF loads, the ISPLSI 1032-60LT dissipates approximately 1.5 W (CV^2 f = 64 x 50e-12 x 5^2 x 60e6 = 4.8 W theoretical, derated for typical 30% activity). The TQFP-100 has typical theta_JA of 35 C/W, so junction temperature rise above ambient is approximately 53 C; provide copper pours at low elevations and 100+ vias under the exposed pad area.
Thông tin tuân thủ
RoHS/lead-free status is not confirmed in the verified web data. The ISPLSI 1032-60LT is an obsolete legacy 5 V part; Lattice datasheet mirror does not explicitly state RoHS compliance. AEC-Q100 not applicable for a 5 V industrial CPLD.
