AD623BN - Low-Cost Rail-to-Rail Instrumentation Amplifier | Analog Devices
MPN: AD623BN ✓ Hoạt độngAD623BN Tóm tắt
An instrumentation amplifier is a specialized analog IC that amplifies the voltage difference between two inputs while providing high common-mode rejection. Its internal signal path rejects interference shared by both inputs, making it more effective than a conventional operational amplifier when sensors, bridges, and measurement nodes are exposed to common-mode voltage. The AD623BN belongs to the instrumentation-amplifier hierarchy within analog signal-chain and amplifier ICs.
The AD623BN's rail-to-rail output allows the output signal to approach the supply limits, improving dynamic range in low-voltage systems. Its gain can be set with one external resistor, simplifying circuit construction compared with implementations requiring a complete feedback network. The verified product listing identifies a maximum offset of 160 uV, input bias current of 17 nA, and bandwidth of 800 kHz. These characteristics make the part relevant to bridge-based sensing and low-level differential measurements.
The architecture supports single-supply operation from 2.7 V to 12 V as well as dual-supply operation. In single-supply systems, the reference input defines the output's midpoint, while the rail-to-rail output stage preserves signal swing near the upper and lower rails. Designers should account for output settling time, input common-mode range, gain error, and power-supply rejection when selecting gain and filtering.
Typical uses include weighing and force sensing, pressure and strain measurements, current-shunt monitoring, biomedical instrumentation, industrial process control, and sensor interfaces. The 800 kHz bandwidth accommodates higher-bandwidth sensing paths, while the low offset and bias current help preserve accuracy near the measurement floor. Application filtering should remain separate from the instrumentation amplifier's gain selection.
For a new PCB, verify every pin function and supply-decoupling arrangement against the manufacturer datasheet. Keep the gain resistor close to the gain-setting pin, provide stable bypass capacitance at the supply pins, and route the differential inputs symmetrically to reduce sensitivity to unequal parasitics. The manufacturer product page and AD623 datasheet are the primary references for electrical limits, gain equations, and recommended application circuits.
This page combines the manufacturer's operating characteristics with practical design guidance, packaging details, application context, and same-footprint replacement options. It is intended to help engineers compare the AD623BN against other instrumentation amplifiers without overlooking input bias, offset, bandwidth, supply voltage, or reference-pin differences.
Bộ thay thế dễ dàng lắp đặt cho AD623BN — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với AD623BN (cùng hình factor và footprint) — khác nhau ở Package, RoHS Status, Mounting Type, Number of Circuits, Product Type.
AD623ARZ-R7
✅ Drop-In ⚠️ Thông số chưa được xác minh✓ Còn hàng
$2.65 / Đơn vị
Xem tài liệu →AD623ARZ-R7
✅ Drop-In ⚠️ Thông số chưa được xác minh✓ Còn hàng
$2.65 / Đơn vị
Xem tài liệu →AD623ANZ
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →AD623BN Tỷ lệ tối đa & tính chất điện
| Product Type | Single-channel instrumentation amplifier |
| Supply Voltage Range | 2.7 V to 12 V |
| Supply Configuration | Single or dual supply |
| Output Swing | Rail-to-rail |
| Gain Programming | Single external gain-set resistor |
| Maximum Input Offset Voltage | 160 uV |
| Input Bias Current | 17 nA |
| Bandwidth | 800 kHz |
| Channel Count | 1 channel |
| Hộp | PDIP-8, plastic |
| Số chân | 8 pins |
| Kiểu lắp đặt | Through-hole |
| Trạng thái RoHS | Compliant |
Cấu hình chân AD623BN
| Chân 1 | RG — Gain-setting resistor connection |
| Chân 2 | IN- — Inverting input |
| Chân 3 | IN+ — Noninverting input |
| Chân 4 | V- — Negative supply connection |
| Chân 5 | REF — Reference input for output voltage |
| Chân 6 | OUT — Amplified output |
| Chân 7 | V+ — Positive supply connection |
| Chân 8 | RG — Gain-setting resistor connection |
Ứng dụng tiêu biểu
AD623BN phù hợp cho 6 Áp dụngs: Strain-Gauge Bridge Measurement, Pressure Transducer Interface, Current-Shunt Monitoring, Biomedical Sensor Signal Conditioning, Industrial Process Sensing, Portable Instrument and Test Equipment.
Strain-Gauge Bridge Measurement
The AD623BN fits strain-gauge bridges because its differential input stage measures the small bridge imbalance while rejecting the larger common-mode excitation voltage. Its 160 uV maximum input offset and 17 nA input bias current directly affect the measurable resolution, while 800 kHz bandwidth supports mechanical responses that do not require a high-speed amplifier. The device is used between the bridge and an ADC, with gain set by one resistor and the reference input defining the output level in a single-supply system. Layout symmetry around the RG pin is important because unequal parasitic capacitance and resistance can degrade CMRR. Final accuracy must also account for bridge tolerance, excitation drift, gain error, and ADC input range.
Được đề xuất
Pressure Transducer Interface
The AD623BN is appropriate for piezoresistive pressure transducers that produce a differential signal superimposed on a common-mode voltage. Instrumentation-amplifier architecture rejects much of that shared voltage, while the 800 kHz bandwidth allows the circuit to follow pressure changes with useful margin. The low 17 nA bias current limits loading of high-impedance sensor bridges, and the 160 uV offset limit defines a key contributor to full-scale measurement error. In a 5 V single-supply design, the reference input establishes the output center point. Place the gain resistor close to RG and route both sensor inputs away from switching supplies to preserve differential-signal integrity.
Được đề xuất
Current-Shunt Monitoring
The AD623BN can measure the small voltage generated by a current shunt without requiring a separate differential amplifier and output network. Its instrumentation-amplifier configuration rejects supply-related and return-path noise that appears equally on both shunt terminals. The 800 kHz bandwidth is suitable for many power-conversion monitoring loops, while the 2.7 V minimum supply permits operation from low-voltage rails. Rail-to-rail output helps retain measurement swing in compact systems, and the reference input can shift the output into an ADC-centered range. Designers must verify common-mode limits at the selected gain, account for offset and gain error, and use Kelvin routing when shunt resistance is low.
Được đề xuất
Biomedical Sensor Signal Conditioning
The AD623BN can condition low-level differential signals from biomedical electrodes, temperature sensors, and impedance-monitoring circuits when the system error budget permits its offset and noise performance. Differential instrumentation amplification helps suppress physiological excitation and other common-mode signals, while the 17 nA input bias current reduces disturbance of high-impedance sources. Single-supply operation from 2.7 V to 12 V supports compact portable systems, and the reference input supports an ADC-compatible output baseline. Isolation, patient protection, frequency response, and electrode-specific safety requirements remain outside the amplifier's function. Use the manufacturer electrical limits to verify input range, output swing, and noise before selecting the gain.
Được đề xuất
Industrial Process Sensing
The AD623BN suits industrial sensor interfaces where a controller must recover a small differential measurement from a larger common-mode voltage. Its 800 kHz bandwidth is useful for process variables with moderate dynamic content, and the single external gain resistor simplifies field-selectable scaling. The rail-to-rail output supports systems that need more of the available supply range, while single- or dual-supply operation allows flexibility in 5 V and industrial control rails. For reliable operation, check the input common-mode range against bridge or transducer excitation, keep the input pair symmetric, and isolate sensitive traces from motors and relays. Offset drift, gain error, resistor tolerance, and ADC resolution usually dominate final measurement accuracy.
Được đề xuất
Portable Instrument and Test Equipment
The AD623BN fits portable measurement equipment that uses low-voltage supplies and needs accurate differential-signal conditioning. Its 2.7 V minimum operating voltage permits compact single-supply designs, while the reference input allows the output to be biased for a mid-range ADC. The rail-to-rail output improves signal utilization, and 800 kHz bandwidth supports general-purpose instrumentation rather than only static measurements. A practical design should include local supply bypassing, careful grounding, and an input filter selected according to sensor noise and required response time. Because the gain-setting resistor and input bias current affect accuracy, the complete measurement chain should be calibrated rather than relying on nominal gain alone.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD623BN — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AD623AR | AD623ARZ | AD623AN |
|---|---|---|---|---|
| Package | PDIP-8 | PDIP-8 - same package | PDIP-8 - same package | PDIP-8 - same package |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Product Type | Single-channel instrumentation amplifier | Single-channel instrumentation amplifier | Single-channel instrumentation amplifier | Single-channel instrumentation amplifier |
Bảo phân biệt quan trọng
- Rail-to-rail output from a 2.7 V minimum supply (vsAD623AN)
- Single-resistor gain programming (vsAD623AR)
- Verified RoHS-compliant sourcing identity (vsAD623ARZ)
Ghi chú thiết kế
Place the external gain-setting resistor directly between the two RG connections, using the shortest practical routing. Keep the IN+ and IN- paths adjacent and similarly terminated so parasitic capacitance and resistance affect both inputs equally. Avoid routing either input beneath digital clocks, relay contacts, switching-regulator inductors, or other high-impedance noise sources. A continuous ground plane beneath the sensitive analog section will generally produce a more repeatable result than a fragmented split-plane arrangement.
Place local bypass capacitance close to V+ and V- and connect it with short, low-inductance paths. The exact capacitance and whether an additional charge-pump or DC-DC supply is required depend on the gain, input common-mode voltage, and output voltage specified in the AD623 datasheet. For single-supply operation, set REF to the required output midpoint and confirm that the output and input common-mode ranges include the intended signal. Do not assume rail-to-rail output alone guarantees rail-to-rail input operation.
Treat IN+ and IN- as a coupled differential pair from the sensor or bridge through to the amplifier. Keep their geometry and surrounding ground references symmetrical, and terminate unused channels according to the manufacturer's guidance when multiplexing several sensors. Use filtering that suppresses out-of-band noise without unnecessarily reducing the 800 kHz signal bandwidth. For very low source impedances, check the gain resistor network and input protection arrangements against the AD623 datasheet before adding external capacitance.
Do not select the AD623BN solely from its 800 kHz headline bandwidth because closed-loop bandwidth changes with gain, and its 160 uV offset can dominate a small-signal measurement. Verify input common-mode range, output swing, reference-pin behavior, supply current, and temperature grade against the complete measurement range. Also confirm that the selected PDIP-8 alternative has the same pin functions and gain equation; identical package dimensions alone do not guarantee drop-in compatibility.
Thông tin tuân thủ
RoHS compliance is identified by the LCSC product listing. No separate REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement is established by the available manufacturer information.