AD707TQ - 15uV Max Offset Precision Op Amp | Analog Devices
MPN: AD707TQ ✓ Hoạt độngAD707TQ Tóm tắt
An operational amplifier is a voltage-gain element used throughout analog signal chains. It can amplify sensor outputs, buffer high-impedance sources, support active filters, and perform error amplification in feedback-control systems. The AD707 belongs to the operational-amplifier hierarchy, where precision amplifiers are selected for low offset voltage, low bias current, low drift, and predictable behavior across changing temperatures. The AD707 is designed for instrumentation, industrial measurement, and precision signal-conditioning systems.
The AD707's defining performance begins with its maximum offset voltage of less than 15 uV. Analog Devices identifies the top grade as the first bipolar monolithic operational amplifier to offer a maximum offset-voltage drift of 0.1 uV/°C. Its maximum input offset current is 1.0 nA, which is especially useful when the source impedance is high or source leakage would otherwise create measurement error. The 0.9 MHz bandwidth makes it appropriate for instrumentation rather than high-speed signal processing.
Internally, the AD707 is a bipolar precision amplifier combining low-offset architecture with direct-coupled operation. Its electrical performance supports closed-loop gains where offset error must remain small relative to the measured signal. Designers should still account for bias-current error, input bias noise, common-mode limits, supply headroom, and the finite bandwidth when calculating practical measurement accuracy.
Typical uses include precision current-to-voltage conversion, low-level sensor amplification, bridge-signal conditioning, laboratory instrumentation, and feedback control in industrial systems. The 8-pin CDIP format can also suit high-reliability or temperature-controlled assemblies where a hermetically sealed package is preferred over a molded plastic package. Its low offset makes it useful when the measurement spans only a small voltage range close to the zero point.
For best results, place the amplifier close to sensitive input nodes, use low-leakage protection components, and avoid source impedances that make input-bias-current error excessive. Power-supply bypassing and careful grounding remain essential because the amplifier cannot correct noise already introduced by the input network. Confirm the operating voltage, temperature limits, and electrical limits against the manufacturer datasheet before finalizing a high-reliability design.
This product page combines manufacturer specifications, package information, pricing structure, and precision-amplifier design guidance to support component selection and board-level implementation. It also provides application-focused explanations and a transparent comparison with the screened AD707TQ/883B option for engineers evaluating legacy or controlled procurement requirements.
Bộ thay thế dễ dàng lắp đặt cho AD707TQ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
AD707TQ/883B
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD707TQ Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Single general-purpose operational amplifier |
| Architecture | Bipolar monolithic |
| Maximum Input Offset Voltage | Less than 15 uV |
| Maximum Input Offset Current | 1.0 nA |
| Maximum Offset Voltage Drift | 0.1 uV/°C for the top grade |
| Gain-Bandwidth Product | 0.9 MHz |
| Hộp | 8-pin CDIP, hermetically sealed ceramic |
| Số chân | 8 pins |
| Kiểu lắp đặt | Through-hole |
Hướng dẫn cấu hình chân AD707TQ 8-pin cdip, hermetically sealed ceramic
Cấu hình chân cho AD707TQ (8-pin cdip, hermetically sealed ceramic gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho AD707TQ.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AD707TQ phù hợp cho 3 Áp dụngs: Điều kiện tín hiệu, Thiết bị thu thập dữ liệu, Xử lý âm thanh.
Điều kiện tín hiệu
Phân tích và lọc tín hiệu cảm biến sử dụng AD707TQ.
Thiết bị thu thập dữ liệu
Chuyển đổi tín hiệu tương tự thành quá trình số sử dụng AD707TQ.
Xử lý âm thanh
Phân tích và khuếch đại tín hiệu âm thanh sử dụng AD707TQ.
Dữ liệu tham khảo kỹ thuật cho AD707TQ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AD707TQ/883B |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | CDIP-8 | CDIP-8 |
| Function | Single general-purpose precision operational amplifier | Single precision operational amplifier |
| Architecture | Bipolar monolithic | Bipolar monolithic |
| Maximum Input Offset Voltage | Less than 15 uV | Less than 15 uV |
| Gain-Bandwidth Product | 0.9 MHz | 0.9 MHz |
| Circuit Count | 1 circuit | 1 circuit |
Bảo phân biệt quan trọng
- Precision offset performance for low-level measurements (vsAD707TQ/883B)
- Low input offset current supports higher source impedance (vsAD707TQ/883B)
- Hermetically sealed ceramic construction for controlled assemblies (vsAD707TQ/883B)
Ghi chú thiết kế
Treat input-bias-current error as a source-impedance problem rather than only an amplifier specification. With a maximum input offset current of 1.0 nA, every 1 MΩ of source impedance can create approximately 1 uV of bias-related error. Use the AD707TQ with suitably low source impedances, or include offset-current compensation when the sensor or resistor network cannot be changed.
Route the amplifier inputs as short and guarded as practical, particularly when the AD707TQ is used with high-impedance sensors. Keep input nodes away from switching nodes and power-supply return currents. If a guard trace is used, it should be driven by a voltage near the input common-mode potential; otherwise the guard itself can alter input bias current and measurement accuracy.
Design the supply rails around the amplifier's documented operating range and verify output swing at the selected load. Because this is a bipolar precision amplifier, common-mode headroom and output-swing limits must be checked rather than assuming the input and output can reach the supply rails. Add local supply bypassing and keep ground returns short to minimize converted supply noise.
Estimate junction temperature from the actual power dissipation and the thermal resistance associated with the specific CDIP variant and PCB implementation. The 0.9 MHz bandwidth generally limits continuous high-frequency loading, but sustained output current or operation near the upper temperature limit can still raise device temperature. Confirm the applicable environmental limits and hermetic-package assembly requirements before production release.
Thông tin tuân thủ
The Analog Devices product information identifies a precision bipolar operational amplifier in an 8-pin hermetically sealed ceramic CDIP package, but it does not state the requested environmental compliance statuses.