AD745SQ - 20 MHz Ultra-Low-Noise JFET Op Amp | ADI
MPN: AD745SQ ✗ Cuối đờiAD745SQ Tóm tắt
A JFET-input operational amplifier is a voltage-feedback amplifier whose input stage uses junction field-effect transistors. Within the semiconductor hierarchy, it belongs to the operational-amplifier, analog-amplifier, and integrated-amplifier categories. This input architecture is particularly useful when measuring or amplifying signals from high-impedance sensors because it can combine high input impedance, low bias current, low input noise, and wide signal bandwidth in a single monolithic circuit.
The AD745 family is identified for its ultralow-noise, high-speed operation. The published 20 MHz gain-bandwidth figure supports closed-loop bandwidth beyond the 10 V/µs range with suitable feedback networks, while the 12.5 V/µs slew rate allows large-amplitude signals to be reproduced with relatively low distortion. Its operating supply current is 8 mA, and the specified temperature range extends from -55°C to 125°C. Exact voltage-noise, input-bias-current, input-offset-voltage, and supply-voltage limits should be taken from the AD745 manufacturer datasheet for the selected temperature and supply conditions.
BiFET input stages provide a practical compromise between bipolar and CMOS input amplifiers. Bipolar inputs commonly offer low voltage noise, while FET inputs minimize input bias current and simplify the drive of high-source-impedance transducers. The AD745SQ uses this architecture for applications requiring both bandwidth and low-noise signal handling. Its voltage-noise and common-mode performance remain sensitive to circuit configuration, so resistor values, source impedance, and feedback topology must be evaluated together rather than as isolated specifications.
Typical uses include low-level transducer amplification, audio and instrumentation signal chains, laboratory measurement systems, and precision analog filters. The 8-pin CERDIP package also makes the AD745SQ suitable for legacy industrial and scientific equipment that uses through-hole op-amp footprints. Because Analog Devices marks the AD745 family as not recommended for new designs, engineers should verify long-term availability and consider a currently recommended amplifier for new production programs.
For a new PCB, do not substitute a surface-mount amplifier without confirming that its electrical performance, supply requirements, pin function, stability behavior, and thermal characteristics satisfy the original design. For an existing 8-pin CERDIP board, preserve adequate supply decoupling, route the feedback loop for minimum parasitic capacitance, and avoid using a long input trace next to high-current switching nodes. These practices help preserve the intended bandwidth and noise performance.
This product page combines the AD745 family specifications, lifecycle information, package details, sourcing guidance, and design-focused guidance for the AD745SQ. It also distinguishes true same-package alternatives from broader functional equivalents, helping engineers make a drop-in decision without confusing electrical similarity with PCB compatibility.
Bộ thay thế dễ dàng lắp đặt cho AD745SQ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
AD745AQ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →AD745SQ Tỷ lệ tối đa & tính chất điện
| Amplifier Type | JFET-input operational amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 20 MHz |
| Slew Rate | 12.5 V/µs |
| Điện áp cung cấp | 8 mA |
| Khoảng nhiệt độ hoạt động | -55°C to +125°C |
| Hộp | 8-pin CERDIP |
| Kiểu lắp đặt | Through-hole |
| AEC-Q100 Qualification | Not applicable |
Hướng dẫn cấu hình chân AD745SQ 8-pin cerdip
Cấu hình chân cho AD745SQ (8-pin cerdip gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho AD745SQ.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AD745SQ phù hợp cho 6 Áp dụngs: Precision Transducer Signal Conditioning, High-Input-Impedance Measurement Front End, Laboratory Audio Preamplifier, Precision Analog Filter, Legacy Scientific Instrument Repair, Low-Level Sensor Buffer.
Precision Transducer Signal Conditioning
The AD745SQ is appropriate for amplifying weak sensor signals where low input bias current is needed to avoid loading the source. Its JFET input stage supports high-impedance sensing, while the 20 MHz gain-bandwidth product and 12.5 V/µs slew rate provide useful bandwidth for sensors with moderately fast transients. Place the amplifier close to the transducer, use short guarded input routes, and select feedback resistors that keep the closed-loop noise acceptable. The main trade-off is that a legacy 8-CERDIP package and not-recommended-for-new-designs status make this choice more appropriate for maintenance than unrestricted new development.
Được đề xuất
High-Input-Impedance Measurement Front End
The AD745SQ can serve as the first amplification stage in a high-input-impedance measurement front end because its BiFET input architecture combines very low input current with low voltage noise. The 20 MHz bandwidth is substantially higher than the bandwidth normally required for static bridge or potentiometer signals, preserving rise time during transient tests. To prevent errors, calculate the bias-current offset for the actual source impedance and evaluate the source capacitance against the closed-loop gain. Board layout should isolate high-impedance nodes from clock, relay, and power-converter traces to preserve measurement accuracy.
Được đề xuất
Laboratory Audio Preamplifier
The AD745SQ is suitable for a low-level laboratory audio preamplifier when low noise and adequate bandwidth are both important. Its 12.5 V/µs slew rate and 20 MHz gain-bandwidth product support audio signals well beyond the conventional 20 kHz band while preserving low-noise operation from a JFET input stage. The amplifier should operate with feedback values that maintain stability at the intended closed-loop gain, and input biasing must avoid adding unnecessary thermal noise. Verify output swing against the selected load and supply voltage, especially when designing a microphone or line-level input with large transient peaks.
Được đề xuất
Precision Analog Filter
The AD745SQ can implement active analog filtering where a low-noise, high-input-impedance stage is required. Its 20 MHz gain-bandwidth product leaves bandwidth margin above many sensor-band filter sections, while the 12.5 V/µs slew rate helps preserve low distortion in moderate-amplitude signals. Component tolerances and the amplifier's gain-bandwidth behavior affect the realized filter response, so simulation should include realistic source and load impedances. Keep feedback loops compact, place input and output decoupling according to the datasheet guidance, and verify stability before using the circuit at the highest intended closed-loop gain.
Được đề xuất
Legacy Scientific Instrument Repair
AD745SQ is especially relevant to maintenance of legacy scientific instruments that use an 8-pin CERDIP JFET operational amplifier. The specified operating temperature range of -55°C to +125°C supports harsh laboratory and industrial environments, while the established through-hole package facilitates socketed or PCB-level replacement. Before installation, compare the complete ordering code, package dimensions, and electrical limits with the removed device. Because the manufacturer marks the family as not recommended for new designs, use the replacement for maintaining proven equipment unless a longevity review approves continued incorporation in new builds.
Được đề xuất
Low-Level Sensor Buffer
The AD745SQ works as a buffer or gain stage for low-level sensors requiring both high input impedance and low voltage noise. The JFET input architecture minimizes bias-current loading, and the 20 MHz gain-bandwidth product allows the stage to retain useful bandwidth when configured for modest gain. The design should account for sensor noise, amplifier noise, resistor noise, and the parallel combination of input bias current and source resistance. A low-noise reference and appropriately decoupled supply are also important because reference or supply noise can dominate the sensor signal. Confirm operation across the complete temperature range when precision drift matters.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD745SQ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AD745AQ |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 8-pin CERDIP | 8-pin CERDIP |
| Amplifier Architecture | JFET-input operational amplifier | JFET-input operational amplifier |
| Number of Circuits | 1 circuit | 1 circuit |
| Gain-Bandwidth Product | 20 MHz | 20 MHz |
| Slew Rate | 12.5 V/µs | 12.5 V/µs |
| Supply Current | 8 mA | 8 mA |
| Operating Temperature Range | -55°C to +125°C | -55°C to +125°C |
| Lifecycle Status | Not recommended for new designs | Not recommended for new designs |
Bảo phân biệt quan trọng
- Combines JFET input behavior with high-speed amplification (vsAD745AQ)
- Supports wide operating temperature range (vsAD745AQ)
- Maintains low quiescent supply demand (vsAD745AQ)
Ghi chú thiết kế
Route both input and feedback connections as short and compact as possible because parasitic capacitance in the feedback loop can reduce stability at high closed-loop gain. For high-impedance inputs, use a guarded or guarded-plus-driven layout where practical, keep the amplifier close to the source, and avoid routing sensitive nodes beside switching-regulator, relay, and digital-clock traces. This is especially important when the source impedance is high enough that bias-current and thermal-noise effects dominate the measurement.
Use the supply voltages and decoupling arrangement specified by the Analog Devices AD745 manufacturer datasheet. Keep the regulator or supply trace short, provide local high-frequency bypass at the device, and avoid sharing long supply-return paths with noisy output stages. Since the published supply current is 8 mA, power capacity is rarely the primary limitation; the more important checks are voltage tolerance, output-current margin under transient load, and the noise contribution of the selected supply topology.
Do not treat every AD745 order code as mechanically interchangeable. AD745SQ is identified as the 8-CERDIP ordering option, and any replacement must be checked against the official package drawing, pin descriptions, qualification code, and electrical limits. In addition, the AD745 family is marked as not recommended for new designs. For legacy maintenance, confirm the removed device and candidate suffix carefully; for new equipment, evaluate a currently recommended amplifier with verified noise, input-current, bandwidth, slew-rate, supply, and stability characteristics.
Thông tin tuân thủ
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was identified for the exact AD745SQ ordering code. The component is an analog operational amplifier and is not an automotive-qualified AEC-Q100 device.