AD843SH - 34MHz CBFET Op Amp | Analog Devices
MPN: AD843SH ✓ Hoạt độngAD843SH Tóm tắt
A CBFET-input operational amplifier is a voltage-feedback amplifier whose field-effect-transistor input stage provides very low input bias current while retaining wide signal bandwidth. This input architecture places the AD843 in the operational-amplifier hierarchy, where low bias current reduces disturbance in high-impedance sources while the amplifier provides gain, buffering, filtering, or level shifting.
Key characteristics include a 34 MHz gain-bandwidth product, 135 ns settling time, 19 nV/√Hz input noise at 10 kHz, 250 V/µs slew rate, and 72 dB nominal common-mode rejection. Built-in compensation simplifies implementation, while the specified 2 µV/°C input-offset temperature coefficient supports stable operation over wide ambient-temperature ranges.
The AD843's fast settling behavior is particularly important when a large input step must settle accurately before a subsequent sampling or conversion event. Its 10 V settling specification provides a clear, application-relevant criterion for evaluating acquisition systems. The CBFET input stage also supports use with high-impedance transducers where low input current is important, although the complete external circuit must still satisfy the amplifier's stability and loading requirements.
Typical uses include precision pulse acquisition, high-speed instrumentation, photodiode and capacitance measurement front ends, waveform conditioning, and industrial or military test equipment. The -55°C to +125°C range makes the AD843SH appropriate where temperature variation must be considered, while its high-voltage, wide-bandwidth characteristics suit bipolar signal conditioning.
PCB implementation should preserve short feedback paths and minimize parasitic capacitance around the high-impedance input nodes. Decoupling capacitors should be placed close to the supply pins, and unused or unused-function pins should be handled according to the manufacturer datasheet. Adequate input and output headroom must be checked at temperature because the 135 ns settling specification is not a substitute for stable operating conditions.
This page combines the manufacturer's AD843 family specifications with package details, thermal-range information, application guidance, and verified drop-in replacement analysis. The comparison material is intended to support schematic review, footprint verification, and procurement planning rather than replacing the complete manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho AD843SH — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếAD843SH Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Fast-settling voltage-feedback operational amplifier |
| Input Stage | CBFET input |
| Gain-Bandwidth Product | 34 MHz |
| Settling Time | 135 ns to within 0.01% of final value for a 10 V step |
| Input Bias Current | 0.6 nA |
| Supply Voltage Range | -18 V to +18 V |
| Khoảng nhiệt độ hoạt động | -55°C to +125°C |
| Input Noise Density | 19 nV/√Hz at 10 kHz |
| Maximum Input Offset Voltage | 4.5 mV |
| Slew Rate | 250 V/µs |
| Input Offset Temperature Coefficient | 2 µV/°C |
| Input Current | 600 pA |
| Common-Mode Rejection Ratio | 72 dB nominal |
| Compensation | Built-in compensation |
| Hộp | TO-8-12 metal-can package |
| Số lượng chân | 12 pins |
| Trạng thái RoHS | Compliant |
Hướng dẫn cấu hình chân AD843SH to-8-12 metal-can package
Cấu hình chân cho AD843SH (to-8-12 metal-can package gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho AD843SH.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AD843SH phù hợp cho 6 Áp dụngs: High-Speed Pulse Acquisition, Photodiode Signal Conditioning, Precision Waveform Conditioning, Capacitance Measurement Front End, Industrial Test and Measurement, Military and Aerospace Signal Conditioning.
High-Speed Pulse Acquisition
The AD843SH fits pulse-acquisition front ends that must recover rapidly after a large input transition. Its 34 MHz gain-bandwidth product and 135 ns settling time to within 0.01% of final value for a 10 V step allow the amplifier to establish an accurate output level before the next sampling decision. The 250 V/µs slew rate limits large-signal distortion during abrupt edges. Place the amplifier close to the source and acquisition device, use short feedback traces, and confirm that source capacitance remains within the stability requirements of the AD843 family.
Được đề xuất
Photodiode Signal Conditioning
The AD843SH is suitable for photodiode amplifiers because its 0.6 nA input bias current places a small DC load on a high-impedance detector. Its 34 MHz bandwidth supports higher-bandwidth optical measurement signals, while the 135 ns settling specification can help the output settle quickly between acquisition events. Biasing resistors, diode capacitance, input guarding, and leakage current must still be evaluated because the amplifier specification alone does not determine total system noise or usable signal bandwidth.
Được đề xuất
Precision Waveform Conditioning
The AD843SH can condition bipolar waveforms in instrumentation where rapid acquisition and accurate large-signal recovery are important. Its -18 V to +18 V supply range provides useful headroom for positive and negative signal swings, and the 250 V/µs slew rate helps preserve square or pulse waveforms. The 72 dB nominal common-mode rejection reduces disturbance from common-mode signals, although layout and source impedance remain important for achieving the expected system performance.
Được đề xuất
Capacitance Measurement Front End
The AD843SH is appropriate for capacitive sensor front ends that benefit from low input bias current and fast settling. Its 0.6 nA bias current limits one source of error at the sensing node, and its 34 MHz bandwidth can accommodate higher-frequency capacitance changes. The design should minimize parasitic capacitance around the input, provide adequate guarding, and verify compensation with the actual sensor and cable. Excessively high source or loop capacitance can reduce stability even when the amplifier's headline bandwidth is sufficient.
Được đề xuất
Industrial Test and Measurement
The AD843SH supports industrial instrumentation requiring a wide operating-temperature range and rapid response. The -55°C to +125°C specification supports deployments across wide ambient conditions, while the 135 ns settling behavior helps repeated measurements settle between stimulus events. For factory or laboratory equipment, use the specified operating supply range and temperature limits, account for offset drift through the 2 µV/°C coefficient, and provide stable reference and excitation circuitry.
Được đề xuất
Military and Aerospace Signal Conditioning
The AD843SH's -55°C to +125°C operating range makes it suitable for temperature-extreme signal-conditioning applications. Its CBFET input stage provides 0.6 nA bias current, while the 34 MHz bandwidth and 135 ns settling time address fast transient signals. Qualification for a particular aerospace or defense program still requires the applicable procurement documentation, traceability, and screening requirements. Circuit designers should verify supply tolerances, grounding, component derating, and environmental constraints independently.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD843SH — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Brand | Analog Devices |
| Package | TO-8-12 metal-can package |
| Number of Pins | 12 pins |
| Amplifier Type | Fast-settling voltage-feedback operational amplifier |
| Input Stage | CBFET input |
| Gain-Bandwidth Product | 34 MHz |
| Settling Time | 135 ns to within 0.01% after a 10 V step |
| Supply Voltage Range | -18 V to +18 V |
| Input Bias Current | 0.6 nA |
| Slew Rate | 250 V/µs |
| Operating Temperature Range | -55°C to +125°C |
Bảo phân biệt quan trọng
- Fast large-step recovery (vsOPA177)
- Low input bias current (vsOPA671AP)
- Wide operating temperature range (vsAD843SQ)
Ghi chú thiết kế
Keep the high-impedance input node, feedback components, and input-side ground return compact and free of copper that can increase leakage or parasitic capacitance. The AD843SH's 0.6 nA input bias current benefits from clean guarding and contamination control, particularly in photodiode and capacitance-measurement circuits. Check the actual detector, cable, and PCB capacitance against the AD843 family stability guidance before reducing the feedback impedance.
Route supply and ground connections with short paths and place decoupling capacitors close to the relevant device pins. Preserve a compact feedback loop to limit parasitic feedback capacitance and maintain predictable high-frequency behavior. The 34 MHz bandwidth means interconnect effects can become significant even when the schematic simulation appears ideal, so include realistic source and load capacitance in final verification.
Do not interpret the 34 MHz bandwidth as the maximum usable small-signal frequency for every gain setting, and do not assume that the 135 ns settling specification applies without its stated 0.01% and 10 V step conditions. Evaluate large-signal slew-rate behavior separately, confirm output swing over the required temperature range, and verify common-mode headroom across the full -18 V to +18 V supply capability.
Thông tin tuân thủ
The product listing identifies the AD843SH as RoHS compliant. No explicit REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement was found.