AD96685BR - 2.5ns ECL Comparator | Analog Devices
MPN: AD96685BR ✗ Cuối đờiAD96685BR Tóm tắt
A high-speed comparator is a logic-family device that determines whether a differential input voltage is above or below a switching threshold. The AD96685BR belongs to the comparator hierarchy within high-speed logic ICs, where fast edge response, low delay dispersion, and controlled output levels are more important than general-purpose precision or micropower operation. Its differential input stage supports comparison of two rapidly changing signals while limiting sensitivity to common-mode voltage changes.
The principal feature of the AD96685BR is its 2.5 ns propagation delay, which supports high-speed timing decisions and pulse detection. Its 50 ps propagation-delay dispersion indicates that delay changes only slightly as input overdrive conditions vary. Complementary ECL outputs provide both true and inverted decisions, while the open-emitter architecture permits use of standard transmission-line terminations. These characteristics make the device suitable for clock recovery, edge detection, high-speed data qualification, and pulse-width discrimination.
The AD96685/AD96687 family uses a fast, high-precision differential input stage to maintain consistent propagation delay over its stated input common-mode range. Its outputs can drive transmission lines terminated through 50 ohm resistors to -2.0 V, matching conventional ECL signal-chain practice. Because edge rates are extremely high, trace geometry, termination, grounding, and isolation from adjacent clocks become essential parts of the comparator implementation rather than secondary layout details.
Typical applications include clock and data-edge detection in telecommunications equipment, timing recovery in data-conversion systems, pulse discrimination in instrumentation, high-speed thresholding in industrial control, and clock crossing or zero-cross detection in test equipment. The 16-SOIC package provides a practical surface-mount option, although system designers must minimize trace length and control impedance around the high-speed outputs.
The principal design trade-off is operating speed versus layout sensitivity. A 2.5 ns decision interval leaves little margin for long traces, poorly terminated outputs, or noisy reference sources. Keep input and output paths short, use suitable ECL termination networks, provide a low-impedance ground reference, and avoid routing adjacent high-speed signals beneath the comparator unless the board stackup provides adequate isolation.
This product page combines the manufacturer product designation, lifecycle status, comparator performance figures, termination requirements, package information, and application-focused engineering guidance. It also documents the limits of the available substitution data so engineers can distinguish a verified pin-compatible option from a merely similar high-speed comparator before committing to a board revision.
Bộ thay thế dễ dàng lắp đặt cho AD96685BR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếAD96685BR Tỷ lệ tối đa & tính chất điện
| Comparator Type | Single, differential-input ECL comparator with complementary outputs |
| Propagation Delay | 2.5 ns |
| Propagation Delay Dispersion | 50 ps |
| Input Common-Mode Range | -2.5 V to +5 V |
| Kiểu đầu ra | Complementary open-emitter ECL |
| Logic Compatibility | ECL 10K and 10KH |
| Recommended Output Termination | 50 ohm to -2.0 V |
| Input Architecture | Differential |
| Latch Function | Yes |
| Hộp | 16-SOIC, surface mount |
| Số chân | 16 pins |
| Lifecycle Recommendation | Not recommended for new designs |
Hướng dẫn cấu hình chân AD96685BR 16-soic, surface mount
Cấu hình chân cho AD96685BR (16-soic, surface mount gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho AD96685BR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AD96685BR phù hợp cho 6 Áp dụngs: High-Speed Clock Edge Detection, Pulse-Width Discrimination, Telecommunications Data Qualification, Precision Threshold Cross-Detection, High-Speed Industrial Trigger System, Zero-Crossing Detection.
High-Speed Clock Edge Detection
The AD96685BR fits clock-edge detection circuits that must produce a clean logic decision with very short delay. Its 2.5 ns propagation delay limits the interval between a sensed edge and the resulting transition, while 50 ps propagation-delay dispersion reduces timing variation as overdrive changes. The complementary ECL outputs allow either rising or falling edge to be selected without adding another comparator. Use controlled-impedance routing and 50 ohm-to-minus-2.0-V output termination to preserve edge quality. The main design consideration is that the extremely fast response makes long PCB traces, reflection, and ground bounce more visible than they would be in a slower comparator.
Được đề xuất
Pulse-Width Discrimination
The AD96685BR is appropriate for detecting whether a pulse crosses a defined width by comparing an event signal against a delayed or threshold-derived signal. A nominal 2.5 ns decision delay supports narrow timing windows, and the 50 ps delay dispersion keeps the comparison response more consistent as the input overdrive varies. The differential input accepts complementary or level-shifted timing signals within the -2.5 V to +5 V common-mode range. Place the threshold source close to the device, provide a low-inductance ground, and terminate both ECL outputs according to the data sheet. Engineers should also account for comparator and trace delay when the target pulse width approaches only a few nanoseconds.
Được đề xuất
Telecommunications Data Qualification
The AD96685BR can qualify high-speed data transitions in telecommunications receiver and retiming paths where a rapid, repeatable threshold decision is required. Its differential input stage rejects common-mode variation while the 2.5 ns propagation delay supports fast data-path processing. Complementary open-emitter outputs interface naturally with ECL 10K or 10KH logic when terminated through 50 ohm resistors to -2.0 V. For this use, the board must prevent the comparator’s fast output transitions from coupling into the input reference. Short traces, adjacent-ground guarding, controlled return current, and careful separation from high-current switching paths are essential to preserve decision stability.
Được đề xuất
Precision Threshold Cross-Detection
The AD96685BR supports fast threshold-crossing detection in instrumentation and measurement systems where the desired event is the transition of a differential signal rather than its absolute amplitude. Its common-mode range of -2.5 V to +5 V permits direct comparison of compatible bipolar signals, and the fast input stage helps minimize timing uncertainty between the input event and the digital decision. The complementary outputs provide both normal and inverted threshold indications for downstream counting or capture logic. Designers should create a low-noise threshold reference, keep the input network compact, and verify input slew rate and overdrive requirements against the manufacturer timing and electrical-characteristic tables.
Được đề xuất
High-Speed Industrial Trigger System
The AD96685BR can serve as the fast decision element in an industrial trigger or event-capture system that must respond to narrow transitions. Its 2.5 ns propagation delay and 50 ps delay dispersion are useful when repeatable event timing is more important than slow general-purpose precision. The open-emitter ECL outputs require appropriate termination and isolation from inductive loads, so the output stage should feed a nearby buffer or logic device rather than a long cable. Use a continuous ground plane, compact decoupling, and controlled routing to prevent switching transients from changing the threshold decision. The NRND lifecycle status should also be considered when designing long-lived industrial equipment.
Được đề xuất
Zero-Crossing Detection
The AD96685BR can generate a precise digital indication when a differential analog signal crosses zero or another threshold. Its differential input arrangement is useful when the crossing signal is referenced to a bias network, and the fast 2.5 ns response captures events that slower comparators might blur or miss. The complementary outputs allow both transition directions to be monitored. For best results, the signal should have sufficient slew rate and overdrive, while the threshold reference must remain quiet relative to the input. Keep the comparator close to the receiver, route outputs as controlled-impedance traces, and use the recommended 50 ohm termination to -2.0 V. These steps are particularly important when the crossing event is repetitive and timing jitter must remain low.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD96685BR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
Ghi chú thiết kế
Keep comparator inputs and outputs physically short because the AD96685BR operates with a 2.5 ns propagation delay. Route high-speed outputs over a continuous reference plane, avoid stubs, and keep the input threshold network close to the device. Separate sensitive input traces from clock and data outputs carrying comparable edge rates to reduce capacitive and inductive coupling.
Terminate the complementary open-emitter outputs through 50 ohm resistors to -2.0 V, or use an equivalent ECL termination arrangement. When routes exceed a few centimeters, use controlled-impedance routing and verify transitions with an oscilloscope. Incorrect termination can create reflections, overshoot, ringing, and inconsistent decision timing even when the comparator itself is operating correctly.
Do not treat the AD96687 as a direct replacement for the AD96685BR solely because both belong to the same ultrafast ECL family. The AD96687 is a dual comparator and has different channel and pin requirements. Also review input slew rate, overdrive, latch timing, supply sequencing, and absolute maximum limits in the manufacturer data sheet before adapting an existing AD96685 design.
Provide a low-impedance ground reference and place input, output, and supply-connection paths to minimize loop area. Use a continuous ground plane rather than fragmented return paths, and place any bypass components at the pins identified in the manufacturer application guidance. Because the device is NRND, preserve the footprint and pin mapping for possible sourcing from original inventory or a carefully qualified second source.
Thông tin tuân thủ
Compliance status was not established from the manufacturer product page excerpts. The device is a general-purpose ECL logic IC and is not identified as an AEC-Q100 automotive product.