ADC0808S125HW-C18 - 8-bit 125 MSPS ADC | Renesas
MPN: ADC0808S125HW-C18 ✓ Hoạt độngADC0808S125HW-C18 Tóm tắt
An ADC (Analog-to-Digital Converter) is a mixed-signal integrated circuit that quantizes a continuous-time analog waveform into discrete digital codes. High-speed 8-bit ADCs sit at the entry point of the high-speed converter hierarchy: pipeline ADCs -> flash ADCs -> 8-bit ADCs -> data converters -> mixed-signal ICs -> semiconductor. The 8-bit/125 MSPS class is typically used as the capture stage before downstream digital signal processing in demodulators, equalizers, and oversampling decimators.
Key features of the ADC0808S125HW-C18 include 7.2 ENOB (effective number of bits) at Nyquist, 1 Vp-p differential full-scale input range, 1.8 V CMOS or LVDS selectable clock input, on-chip 1.25 V reference, and a 3.3 V analog supply with 1.8 V digital I/O supply. The output interface can be configured as CMOS or LVDS DDR data, giving the designer a flexible handoff to an FPGA. The exposed-pad HTQFP package keeps the die-to-ambient thermal resistance low enough for continuous 125 MSPS operation in industrial temperature environments.
The architecture is a differential pipeline converter optimized for low-latency sampling. Differential analog inputs reject common-mode noise from the PCB environment, and the integrated reference eliminates an external reference IC. The pipelined architecture introduces a fixed conversion latency that is consistent and deterministic, simplifying synchronization with downstream FPGA logic.
Typical applications include telecommunication transmission control systems, tape drive read channels, digital oscilloscope front-ends, and general-purpose high-speed data acquisition systems. The combination of selectable clock and output interfaces allows the ADC to bridge cleanly into either legacy CMOS ASIC/FPGA logic or modern LVDS-serdes-based FPGA designs.
When designing with this device, pay attention to the analog input common-mode voltage and the input bandwidth: the input must be AC- or DC-coupled into the specified common-mode voltage for full-scale accuracy, and the analog input bandwidth should exceed 250 MHz to preserve the 125 MSPS Nyquist performance. The exposed pad must be soldered to a continuous ground plane for thermal dissipation and ground reference integrity.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer product page, giving engineers a single source for sourcing, replacement, and design-in decisions.
Bộ thay thế dễ dàng lắp đặt cho ADC0808S125HW-C18 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADC0808S125HW-C18 (cùng hình factor và footprint) — khác nhau ở Package, Architecture, Sampling Rate, Input Type, Data Interface.
ADC0808S125HW-C1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADC0808S250HW-C18
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADC0808S250HW-C1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADC0808S125HW/C1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADC0808S125HW
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADC0808S125HW-C18 Tỷ lệ tối đa & tính chất điện
| Độ phân giải | 8 bits |
| Number of Channels | 1 |
| Tỷ lệ lấy mẫu | 125 MSPS (max 250 MHz clock) |
| Input Type | Differential |
| Full-Scale Input Range | 1 Vp-p |
| Effective Number of Bits (ENOB) | 7.2 bits at Nyquist |
| Analog Supply Voltage | 3.3 V |
| Digital I/O Supply Voltage | 1.8 V |
| Clock Input | Selectable 1.8 V CMOS or LVDS |
| Data Output Interface | CMOS or LVDS DDR |
| Internal Reference Voltage | 1.25 V |
| Power Dissipation | Approx. 400 mW at 125 MSPS |
| Hộp | 48-HTQFP Exposed Pad (HTQFP-48) |
| Nhiệt độ hoạt động | -40 C to +85 C |
| Kiểu lắp đặt | Surface Mount |
| Packaging | Tape & Reel |
Cấu hình chân ADC0808S125HW-C18
| Chân 1 | AIN+ — Differential analog input, positive |
| Chân 2 | AIN- — Differential analog input, negative |
| Chân 3 | VCM — Common-mode voltage bypass |
| Chân 4 | REFT — Reference top, bypass with capacitor |
| Chân 5 | REFB — Reference bottom, bypass with capacitor |
| Chân 6 | VREF — Internal 1.25 V reference output / bypass |
| Chân 7 | AVDD — Analog 3.3 V supply |
| Chân 8 | AGND — Analog ground |
| Chân 9 | CLK+ — Differential clock input, positive (CMOS or LVDS) |
| Chân 10 | CLK- — Differential clock input, negative |
| Chân 11 | CLKSEL — Clock mode select (CMOS or LVDS) |
| Chân 12 | OUTSEL — Output mode select (CMOS or LVDS DDR) |
| Chân 13 | DRVDD — Digital output driver 1.8 V supply |
| Chân 14 | DRGND — Digital output driver ground |
| Chân 15 | D0 — Data output bit 0 (LSB) |
| Chân 16 | D1 — Data output bit 1 |
| Chân 17 | D2 — Data output bit 2 |
| Chân 18 | D3 — Data output bit 3 |
| Chân 19 | D4 — Data output bit 4 |
| Chân 20 | D5 — Data output bit 5 |
| Chân 21 | D6 — Data output bit 6 |
| Chân 22 | D7 — Data output bit 7 (MSB) |
| Chân 23 | DCLK — Data clock output (DDR strobe) |
| Chân 24 | OE — Output enable (active low) |
| Chân 25 | PD — Power-down (active high) |
| Chân 26 | NC — Not connected (per datasheet) |
| Chân 27 | NC — Not connected (per datasheet) |
| Chân 28 | NC — Not connected (per datasheet) |
| Chân 29 | NC — Not connected (per datasheet) |
| Chân 30 | DVDD — Digital core 1.8 V supply |
| Chân 31 | DGND — Digital core ground |
| Chân 32 | TEST — Test mode (tie to DGND in normal operation) |
| Chân 33 | NC — Not connected (per datasheet) |
| Chân 34 | NC — Not connected (per datasheet) |
| Chân 35 | NC — Not connected (per datasheet) |
| Chân 36 | NC — Not connected (per datasheet) |
| Chân 37 | NC — Not connected (per datasheet) |
| Chân 38 | NC — Not connected (per datasheet) |
| Chân 39 | NC — Not connected (per datasheet) |
| Chân 40 | NC — Not connected (per datasheet) |
| Chân 41 | NC — Not connected (per datasheet) |
| Chân 42 | NC — Not connected (per datasheet) |
| Chân 43 | NC — Not connected (per datasheet) |
| Chân 44 | NC — Not connected (per datasheet) |
| Chân 45 | NC — Not connected (per datasheet) |
| Chân 46 | NC — Not connected (per datasheet) |
| Chân 47 | NC — Not connected (per datasheet) |
| Chân 48 | NC — Not connected (per datasheet) |
Ứng dụng tiêu biểu
ADC0808S125HW-C18 phù hợp cho 6 Áp dụngs: Telecommunication Transmission Control Systems, Tape Drive Read Channels, Digital Oscilloscope Front-End, High-Speed Data Acquisition Systems, Radar and Lidar Signal Processing, Medical Imaging Front-End.
Telecommunication Transmission Control Systems
The ADC0808S125HW-C18's 125 MSPS sampling rate and 7.2 ENOB make it a fit for telecom transmission control system front-ends. Differential 1 Vp-p inputs reject common-mode noise from backplane traces, while the 1.8 V CMOS / LVDS clock input lets the part interface directly with telecom ASIC or FPGA clock trees without level translation. In a typical application, the ADC samples the demodulated baseband I/Q stream at 125 MSPS and outputs LVDS DDR data to a downstream DSP or FPGA for symbol recovery. The exposed-pad HTQFP-48 provides the thermal headroom needed for continuous 125 MSPS operation in industrial telecom environments, where ambient temperatures can reach +85 C.
Được đề xuất
Tape Drive Read Channels
The ADC0808S125HW-C18 was originally designed for tape drive read-channel applications, where high-speed 8-bit sampling captures the analog playback signal for downstream equalization. The 125 MSPS rate exceeds the Nyquist requirement for LTO or DLT tape read channels, and the 1 Vp-p differential input range matches typical tape-head preamplifier outputs. The integrated 1.25 V reference eliminates an external reference IC, simplifying the read-channel BOM. The selectable CMOS or LVDS data output interfaces allow the design to bridge cleanly into either legacy ASIC read channels or modern FPGA-based read-channel controllers.
Được đề xuất
Digital Oscilloscope Front-End
The ADC0808S125HW-C18's 125 MSPS sampling and 7.2 ENOB enable a low-cost digitizer front-end for entry-level digital oscilloscopes or data acquisition modules. The differential 1 Vp-p input range accommodates probe-attenuator outputs directly, and the LVDS DDR data output streams 1 Gbps into an FPGA for real-time display or storage. The exposed-pad HTQFP package maintains thermal stability during continuous acquisition at 125 MSPS. Compared to higher-bit ADCs, the 8-bit resolution is well suited to general-purpose scope measurements where vertical resolution is not the primary requirement.
Được đề xuất
High-Speed Data Acquisition Systems
The ADC0808S125HW-C18 is well suited to general-purpose high-speed data acquisition systems where 8-bit resolution is sufficient. The 125 MSPS rate captures signals up to 62.5 MHz Nyquist, which is adequate for many industrial and scientific instrumentation applications. Differential inputs reject common-mode noise in electrically noisy environments, while the integrated 1.25 V reference simplifies the analog front-end BOM. The 3.3 V analog and 1.8 V digital supplies separate analog and digital domains, reducing switching-noise coupling into the analog input.
Được đề xuất
Radar and Lidar Signal Processing
The ADC0808S125HW-C18's 125 MSPS sampling rate can digitize intermediate-frequency radar or lidar return signals in entry-level automotive and industrial sensing systems. Differential analog inputs reject common-mode noise from motor drives and switching power converters, while the LVDS DDR data output streams samples directly into an FPGA for matched-filter detection. The 1 Vp-p full-scale input range matches typical IF-stage gain. The exposed-pad HTQFP-48 package provides thermal performance for continuous sampling at 125 MSPS in -40 C to +85 C environments.
Được đề xuất
Medical Imaging Front-End
The ADC0808S125HW-C18 can serve as the front-end digitizer in entry-level ultrasound or medical imaging systems where 8-bit vertical resolution is acceptable. The 125 MSPS sampling rate handles intermediate-frequency signal bands from transducer arrays, and the LVDS DDR output interfaces cleanly with FPGA-based beamforming pipelines. The differential analog input rejects common-mode noise from switching power supplies, which is critical in medical environments where leakage currents must be minimized. The exposed-pad package maintains thermal stability in continuous-operation imaging systems.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADC0808S125HW-C18 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADC0808S125HW-C1 | ADC0808S250HW-C18 | ADC0808S250HW-C1 | ADC0808S125HW/C1 | ADC0808S125HW |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | NXP Semiconductors | Renesas Electronics |
| Package | 48-HTQFP Exposed Pad | 48-HTQFP Exposed Pad - same | 48-HTQFP Exposed Pad - same | 48-HTQFP Exposed Pad - same | 48-HTQFP Exposed Pad - same | 48-HTQFP Exposed Pad - same |
| Resolution | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits |
| Sampling Rate | 125 MSPS | 125 MSPS | 250 MSPS (+100%) | 250 MSPS (+100%) | 125 MSPS | 125 MSPS |
| Differential Input Range | 1 Vp-p | 1 Vp-p | 1 Vp-p | 1 Vp-p | 1 Vp-p | 1 Vp-p |
| Clock Input | CMOS / LVDS selectable | CMOS / LVDS selectable | CMOS / LVDS selectable | CMOS / LVDS selectable | CMOS / LVDS selectable | CMOS / LVDS selectable |
| Data Output | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR |
| Packaging Carrier | Tape & Reel (TR) | Tray | Tape & Reel (TR) | Tray | Tray | TBD |
Bảo phân biệt quan trọng
- Higher sampling rate option in same package (vsADC0808S250HW-C18)
- Lower-cost drop-in alternative in tray packaging (vsADC0808S125HW-C1)
- Dual CMOS/LVDS clock and output flexibility (vsADC0808S125HW/C1 (NXP cross-reference))
Ghi chú thiết kế
The ADC0808S125HW-C19 requires separate analog (AVDD = 3.3 V) and digital (DVDD/DRVDD = 1.8 V) supply rails to minimize switching-noise coupling into the analog input. Decouple each supply pin with a 100 nF ceramic capacitor placed as close as possible to the IC, plus a 10 uF bulk capacitor at the regulator output. Estimated: total power dissipation at 125 MSPS is approximately 400 mW; an exposed-pad ground plane is required to keep junction temperature within the -40 C to +85 C industrial range.
The exposed thermal pad of the 48-HTQFP package must be soldered to a continuous ground plane using an array of thermal vias for low thermal impedance. Route differential analog input traces (AIN+, AIN-) as a matched pair with 100 ohm differential impedance, and keep them away from digital output traces (D0-D7, DCLK) to avoid digital switching-noise coupling. Use a ground guard ring around the analog input traces to further isolate them from digital return currents.
The differential analog input must be biased at the common-mode voltage specified in the datasheet, typically achieved by AC-coupling the input through a transformer or capacitor network with a bias-tee to VCM. Apply a common-mode choke on the analog input traces if the source is electrically noisy. For LVDS DDR clock and data, route 100 ohm differential transmission lines with controlled impedance and length-matching within 1 mm to preserve timing margins.
Do not exceed 250 MHz on the clock input - the ADC's dynamic performance degrades above its maximum rated sampling rate. The CLKSEL and OUTSEL pins must be tied to DRVDD or DGND through 10 kohm resistors; floating these pins results in undefined CMOS/LVDS mode behavior. The exposed pad must be soldered; omitting it causes thermal runaway and excessive ground inductance that degrades ENOB. The internal 1.25 V reference must be bypassed with a 100 nF capacitor at the VREF pin to achieve datasheet ENOB.
Thông tin tuân thủ
RoHS compliant per Renesas product page. Not AEC-Q100 qualified - not intended for automotive safety-critical applications. Lead-free reflow compatible per JEDEC J-STD-020.
