ADF4007BCPZ-RL7 - 7.5 GHz Integer-N PLL Synthesizer | Analog Devices
MPN: ADF4007BCPZ-RL7 ✓ Hoạt độngADF4007BCPZ-RL7 Tóm tắt
A frequency synthesizer is a timing component that uses a phase-locked loop to generate, divide, or regulate a frequency referenced to a stable source. The ADF4007 combines a low-noise digital phase-frequency detector, precision charge pump, and programmable divider or prescaler. Within the clock and timing IC hierarchy, it is an integer-N PLL synthesizer designed for communications equipment requiring accurate frequency translation or clock generation.
The device supports a 3.3 V power supply and a separate charge-pump supply that permits an extended tuning-voltage range. External control pins select among four prescaler-related divide settings, while the reference input establishes the synthesizer's frequency accuracy and stability. These functions make the part suitable for RF signal chains where a fixed reference must control a high-frequency local oscillator.
Technical performance depends on the reference signal, loop filter, charge-pump settings, and output frequency. The Analog Devices ADF4007 data sheet describes a typical circuit using the specified loop-filter components with ADIsimPLL, producing phase noise of -100 dBc/Hz at a 10 kHz carrier offset. The loop filter also attenuates spurs to below -90 dBc in that typical implementation.
Typical applications include wireless transceiver local oscillators, microwave down-converter and up-converter reference planes, instrument clocks, and communications test equipment. An evaluation platform is available as EVAL-ADF4007, with SMA connections for the reference and RF paths and hardware selection of the 8, 16, 32, or 64 divide ratios for rapid PLL characterization.
A successful design must preserve clean reference routing, provide suitable charge-pump and loop-filter networks, and keep the RF output path away from high-current switching nodes. The exposed pad should be connected to the ground plane according to the manufacturer's land-pattern and thermal-layout guidance because it provides both electrical return and heat-dissipation paths.
This product page combines the manufacturer's functional specifications, pricing structure, drop-in alternatives, and application-focused engineering guidance to support faster component selection and implementation of the ADF4007BCPZ-RL7 in communications clock and frequency-synthesis systems.
Bộ thay thế dễ dàng lắp đặt cho ADF4007BCPZ-RL7 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADF4007BCPZ-RL7 (cùng hình factor và footprint) — khác nhau ở Package, Typical Phase Noise, Typical Spur Level, Charge Pump Supply, Reference Divider Ratio.
ADF4007BCPZ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADF4007BCPZ-RL7 Thông số kỹ thuật
| Device Type | Integer-N PLL frequency synthesizer |
| Maximum RF Frequency | 7.5 GHz |
| Maximum PFD Frequency | 120 MHz |
| Reference Input | 20 MHz CMOS |
| Điện áp cung cấp | 3.3 V |
| Charge Pump Supply | Separate VP supply; extended tuning-voltage range |
| Divider Settings | 8, 16, 32, or 64 |
| Divider Control | Two external control pins |
| Input-to-Output Ratio | 2:1 |
| Input Logic | CMOS |
| Kiểu đầu ra | Clock |
| Phase-Locked Loop | Yes |
| Number of Circuits | 1 |
| Khoảng nhiệt độ hoạt động | -40 °C to +85 °C |
| Hộp | 20-lead WFQFN exposed-pad CSP |
| Terminal Count | 20 terminals |
| Kiểu lắp đặt | Surface mount |
| Package Code | HVQCCN |
| Typical Phase Noise | -100 dBc/Hz at 10 kHz carrier offset |
| Typical Spur Level | Below -90 dBc with the specified loop filter |
Hướng dẫn cấu hình chân ADF4007BCPZ-RL7 hvqccn
Cấu hình chân cho ADF4007BCPZ-RL7 (hvqccn gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ADF4007BCPZ-RL7.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ADF4007BCPZ-RL7 phù hợp cho 6 Áp dụngs: Wireless Transceiver Local Oscillator, Microwave Up-Converter and Down-Converter Reference, Communications Test and Measurement Equipment, Microwave Communication Test Loops, RF Signal-Chain Frequency Reference, Clock and Frequency Reference Generation.
Wireless Transceiver Local Oscillator
The ADF4007BCPZ-RL7 is appropriate for a wireless transceiver local-oscillator or frequency-translation stage that must derive a high-frequency signal from a 20 MHz CMOS reference. Its 7.5 GHz maximum RF frequency and 120 MHz maximum PFD frequency provide substantial tuning and phase-detection range for communications architectures. The selectable 8, 16, 32, and 64 divider settings let the designer choose the integer-N relationship needed by the surrounding RF chain. A separate charge-pump supply supports an extended tuning-voltage range, which is useful when the loop filter must cover a wide frequency interval. The practical trade-off is that reference noise, loop bandwidth, and output matching remain central to achieving useful phase-noise and spur performance.
Được đề xuất
Microwave Up-Converter and Down-Converter Reference
The ADF4007BCPZ-RL7 can provide the controlled reference required by microwave up-converter or down-converter signal chains. Operation to 7.5 GHz makes the device applicable where local-oscillator generation must share a common reference with other communications channels. The Analog Devices evaluation hardware includes dedicated RF input and output SMA connections, allowing the frequency path to be characterized before integration. In production, the designer must control RF trace impedance, return loss, and isolation while keeping the phase detector and charge-pump loop compact. The integer-N architecture simplifies frequency planning, although the loop filter must be recalculated whenever the reference frequency, channel spacing, or phase-noise target changes.
Được đề xuất
Communications Test and Measurement Equipment
The ADF4007BCPZ-RL7 is useful in communications test equipment requiring a programmable, reference-locked RF source for calibration or signal-generation blocks. Its 7.5 GHz RF ceiling, programmable divider choices, and 20 MHz CMOS reference input support repeatable multi-channel test setups. The EVAL-ADF4007 platform simplifies initial loop evaluation because its divider-selection links expose the 8, 16, 32, and 64 operating choices. When integrating the device into an instrument, the reference oscillator should have low phase noise and stable supply rails, while the RF output network should be designed for the required frequency range. The loop-filter values should be optimized from the actual phase-noise and spur requirements rather than copied without accounting for board parasitics.
Được đề xuất
Microwave Communication Test Loops
The ADF4007BCPZ-RL7 can be applied to microwave communication test loops in which a stable 20 MHz reference must drive an RF carrier at a selected divider-dependent frequency. The 7.5 GHz maximum operating frequency supports the upper RF range addressed by the ADF4007 family, while the 120 MHz PFD ceiling enables flexible phase-detector rates. During bench setup, the evaluation board allows RF and reference paths to be connected through SMA interfaces and the divider options to be changed without an immediate full custom-board build. Final hardware should minimize loop-filter area and keep sensitive reference and RF nodes away from digital switching circuitry. Supply decoupling must also account for transient current from the separate charge-pump circuit.
Được đề xuất
RF Signal-Chain Frequency Reference
The ADF4007BCPZ-RL7 is suitable for producing a controllable reference within an RF signal chain where phase locking is preferable to a free-running source. Its integer-N divider architecture, external divide control, and separate charge-pump supply allow the tuning network to be tailored to the required channel plan. The 20 MHz CMOS reference input supports direct connection from a suitable clock source when its amplitude, waveform, and noise satisfy the device requirements. RF layout remains critical because the reference, phase-detector, charge-pump, loop-filter, and output paths can create unwanted coupling. Designers should maintain controlled impedance and use a single well-defined ground reference beneath the exposed pad. The same loop-filter framework used for the manufacturer's typical circuit provides a practical starting point for tuning.
Được đề xuất
Clock and Frequency Reference Generation
The ADF4007BCPZ-RL7 can serve as the PLL element in a clock or frequency-reference subsystem when an RF-synthesizer implementation is preferable to a conventional low-frequency clock generator. Its maximum RF frequency of 7.5 GHz and programmable divider settings permit several frequency ratios to be derived from one stable source. The component also accepts a 20 MHz CMOS reference, enabling it to share an existing system clock when the timing quality is suitable. A separate VP supply broadens the available charge-pump and tuning-voltage design space, but it also requires deliberate rail planning. In a multi-rail system, stable sequencing and local decoupling help prevent reference modulation or PLL instability. The principal trade-off is the complexity of an integer-N loop compared with a fixed-frequency clock output.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADF4007BCPZ-RL7 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADF4007BCPZ |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 20-lead WFQFN exposed-pad CSP | 20-lead WFQFN exposed-pad CSP |
| Maximum RF Frequency | 7.5 GHz | 7.5 GHz |
| Maximum PFD Frequency | 120 MHz | 120 MHz |
| Reference Input | 20 MHz CMOS | 20 MHz CMOS |
| Supply Voltage | 3.3 V | 3.3 V |
| Divider Settings | 8, 16, 32, or 64 | 8, 16, 32, or 64 |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C |
| Output Type | Clock | Clock |
Bảo phân biệt quan trọng
- High RF operating range with flexible divider selection (vsADF4007BCPZ)
- Separate charge-pump supply flexibility (vsADF4007BCPZ)
- Communications-focused PLL integration (vsADF4007BCPZ)
Ghi chú thiết kế
Route the 20 MHz reference, charge-pump connection, loop-filter components, and RF output as compact, controlled-impedance paths. Keep the reference trace away from switching nodes and preserve a continuous ground reference under the exposed pad. The loop-filter area should be minimized because parasitic inductance and capacitance can shift the intended loop bandwidth, phase margin, and spur performance.
Plan the 3.3 V supply and separate charge-pump supply as distinct rails, with local high-frequency decoupling placed close to their respective device pins. Estimated: for a 3.3 V rail, 100 nF provides only local high-frequency bypassing and should not replace bulk capacitance sized from the board's transient requirement. Keep the VP value compatible with the charge-pump output swing and the tuning-voltage range required by the loop filter.
Calculate the loop filter from the actual reference frequency, target loop bandwidth, charge-pump current, and phase-noise targets. The Analog Devices data sheet identifies a typical implementation using ADIsimPLL-derived component values, with phase noise of -100 dBc/Hz at a 10 kHz offset and spurs below -90 dBc. Treat those results as a design reference and validate the final layout because PCB parasitics and component tolerances can alter the response.
Do not assume that the base ordering code and the complete reel ordering code can be mixed without procurement and assembly review. Confirm the 20-lead WFQFN exposed-pad land pattern, pin assignments, divider-control levels, reference amplitude, and supply sequencing against the manufacturer data sheet before releasing a PCB or production order.
Thông tin tuân thủ
The component is an industrial-temperature clock and timing IC with a -40 °C to +85 °C operating range. Compliance declarations are not stated in the available product information.