ADF4110BCPZ-RL7 - 550 MHz Integer-N PLL | Analog Devices
MPN: ADF4110BCPZ-RL7 ✓ Hoạt độngADF4110BCPZ-RL7 Tóm tắt
A phase-locked loop, or PLL, is a frequency-control circuit that compares a divided reference signal with a feedback signal and drives a phase error toward zero through feedback. The ADF4110 belongs to the broader hierarchy of frequency synthesizer, clock-generation IC, timing-control integrated circuit, and semiconductor categories. Its integer-N architecture simplifies frequency planning while supporting programmable division ratios for RF channel selection.
The device includes a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, 6-bit A counter, 13-bit B counter, and dual-modulus prescaler. Together, these blocks support programmable frequency synthesis while providing the phase-detection and current-pump functions required by an external passive loop filter. The manufacturer describes the part as production status, and the data sheet is identified as Revision F.
At the circuit level, the ADF4110 family combines a prescaler with programmable A and B counters to produce division ratios for wireless receiver and transmitter local oscillators. The charge-pump output drives an external loop filter, whose component values determine loop bandwidth, reference-spur behavior, phase noise, and settling performance. This architecture favors predictable integer-N implementation when a direct fractional-N synthesizer is not required.
Typical uses include RF local oscillators in wireless receivers and transmitters, frequency-agile communications equipment, industrial RF test systems, and signal-generation instruments. The 550 MHz maximum RF input frequency makes the device particularly relevant to RF front ends operating below 600 MHz, including industrial, scientific, instrumentation, and selected communication bands.
Layout and loop-filter design are critical. Place the charge-pump output and loop-filter components close to the device, provide a low-impedance ground and exposed-pad connection, decouple the supply near the pins, and route high-frequency feedback lines away from sensitive analog nodes. The external loop filter must be calculated against the intended reference frequency, prescaler, division ratio, and phase-noise requirement.
This product page combines the manufacturer’s device specifications with application guidance, package information, practical design notes, and a parameter comparison of related ADF4110-family synthesizers. The comparison focuses on package fit and functional differences so engineers can determine whether a related member is appropriate before changing an RF board design.
Bộ thay thế dễ dàng lắp đặt cho ADF4110BCPZ-RL7 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADF4110BCPZ-RL7 (cùng hình factor và footprint) — khác nhau ở Product Type, Architecture, Charge Pump, Prescaler, Package.
ADF4111BCPZ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADF4112BCPZ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADF4113BCPZ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADF4113HVBCPZ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADF4110BCPZ-RL7 Thông số kỹ thuật
| Product Type | Single integer-N RF PLL frequency synthesizer |
| Maximum RF Input Frequency | 550 MHz |
| Architecture | Integer-N phase-locked loop |
| Prescaler | Programmable dual-modulus P/P+1 prescaler |
| A Counter | 6-bit programmable counter |
| B Counter | 13-bit programmable counter |
| Reference Divider | Programmable divider |
| Phase Detector | Low-noise digital phase-frequency detector |
| Charge Pump | Precision charge-pump output with external loop filter |
| Hộp | 20-lead WFQFN with exposed pad |
| Package Pin Count | 20 pins including exposed pad |
| Kiểu lắp đặt | Surface mount |
| Manufacturer Lifecycle Status | Production |
Cấu hình chân ADF4110BCPZ-RL7
| Chân 1 | VDD — Analog and digital supply input |
| Chân 2 | COM — Charge-pump and loop-filter common connection |
| Chân 3 | OUT — Prescaler output for the phase-frequency detector |
| Chân 4 | RSET — Charge-pump current-setting resistor connection |
| Chân 5 | GND — Analog and digital ground |
| Chân 6 | REFin — Reference input complementary connection |
| Chân 7 | REFin+ — Reference input |
| Chân 8 | DATA — Serial programming data input |
| Chân 9 | LE — Serial programming latch enable |
| Chân 10 | CE — Serial programming chip enable |
| Chân 11 | DB0 — Data bus bit 0 |
| Chân 12 | DB1 — Data bus bit 1 |
| Chân 13 | DB2 — Data bus bit 2 |
| Chân 14 | DB3 — Data bus bit 3 |
| Chân 15 | DB4 — Data bus bit 4 |
| Chân 16 | DB5 — Data bus bit 5 |
| Chân 17 | PFD — Phase-frequency detector output |
| Chân 18 | CP — Charge-pump output driving the external loop filter |
| Chân 19 | SW — Analog and digital ground connection |
| Chân 20 | EP — Exposed pad connected to ground |
Ứng dụng tiêu biểu
ADF4110BCPZ-RL7 phù hợp cho 6 Áp dụngs: Wireless Receiver Local Oscillator, Wireless Transmitter Frequency Synthesizer, Industrial RF Test Instrument, Frequency-Selective Receiver, Communications Signal Generator, Low-Cost RF Frequency Synthesizer.
Wireless Receiver Local Oscillator
The ADF4110BCPZ-RL7 fits a wireless receiver local-oscillator block operating below the device’s 550 MHz RF input limit. Its programmable prescaler, 6-bit A counter, 13-bit B counter, and reference divider allow the synthesizer to derive an LO channel plan from a stable reference. A digital phase-frequency detector and precision charge pump drive an external passive loop filter. Compared with a fixed-frequency oscillator, this architecture permits channel changes without redesigning the RF front end. The key trade-off is loop-filter complexity: component values must be selected for the intended prescaler, division ratio, phase-noise target, and settling requirement.
Được đề xuất
Wireless Transmitter Frequency Synthesizer
The ADF4110BCPZ-RL7 can provide a programmable RF source for wireless transmitter up-conversion and down-conversion stages within its 550 MHz maximum input-frequency range. The integer-N divider chain and programmable reference divider support flexible channel selection, while the charge-pump output permits optimization of phase noise and reference spurs through the external loop filter. In transmit systems, stable reference-clock quality and loop-filter phase margin are especially important because excessive reference multiplication or an unsuitable bandwidth can degrade close-in phase noise and adjacent-channel performance.
Được đề xuất
Industrial RF Test Instrument
The ADF4110BCPZ-RL7 is suitable for industrial RF test equipment that generates or receives programmable signals below 550 MHz. Its programmable prescaler and counter architecture supports multiple test frequencies from a shared reference, while integer-N operation simplifies calibration and channel planning. The external loop filter provides a direct way to balance acquisition time against phase noise and spurious performance for the intended test bandwidth. For production instruments, account for reference-clock drift, temperature-dependent calibration, shield isolation, and the possibility of accumulated reference-multiplier phase noise when selecting the loop bandwidth.
Được đề xuất
Frequency-Selective Receiver
The ADF4110BCPZ-RL7 can support frequency-selective receiver architectures in which a programmable LO tracks a selected channel. The reference divider and A/B counters establish the required integer-N ratio, while the phase-frequency detector and charge pump continuously correct the VCO. This arrangement is useful when several bands must be covered without changing the complete receiver architecture. A critical design consideration is ensuring that every divider combination supports the target RF input and that the loop filter maintains adequate phase margin across the selected prescaler modes and channel ratios.
Được đề xuất
Communications Signal Generator
The ADF4110BCPZ-RL7 is appropriate for compact communications signal-generation modules that require programmable RF frequency synthesis with a maximum input frequency of 550 MHz. The integer-N architecture gives the controller direct access to the prescaler, reference divider, and A/B counters, allowing deterministic frequency setup. Designers should derive the loop-filter values from the selected reference and channel plan rather than reuse a generic component set. The result can be a low-component-count local oscillator suitable for embedded test fixtures, communication panels, and compact laboratory modules.
Được đề xuất
Low-Cost RF Frequency Synthesizer
The ADF4110BCPZ-RL7 offers a practical way to build a low-cost RF frequency synthesizer below 550 MHz because the prescaler, counters, phase detector, and charge pump are integrated into one IC. Only the loop filter and external VCO are required for the core synthesizer function. This integration reduces board area and firmware complexity compared with discrete divider and comparator approaches. The principal limitation is that integer-N architecture can increase reference spurs when a high division ratio is used, so the reference frequency, loop bandwidth, and output-frequency plan should be optimized together.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADF4110BCPZ-RL7 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADF4111BCPZ | ADF4112BCPZ | ADF4113BCPZ | ADF4113HVBCPZ |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 20-WFQFN Exposed Pad | 20-WFQFN Exposed Pad | 20-WFQFN Exposed Pad | 20-WFQFN Exposed Pad | 20-WFQFN Exposed Pad |
| Maximum RF Input Frequency | 550 MHz | 1.2 GHz | 3.0 GHz | 4.0 GHz | 4.0 GHz |
| PLL Architecture | Single integer-N PLL | Single integer-N PLL | Single integer-N PLL | Single integer-N PLL | Single integer-N PLL |
| A Counter | 6-bit programmable | 6-bit programmable | 6-bit programmable | 6-bit programmable | 6-bit programmable |
| B Counter | 13-bit programmable | 13-bit programmable | 13-bit programmable | 13-bit programmable | 13-bit programmable |
| Prescaler | Programmable dual-modulus P/P+1 prescaler | Programmable dual-modulus P/P+1 prescaler | Programmable dual-modulus P/P+1 prescaler | Programmable dual-modulus P/P+1 prescaler | Programmable dual-modulus P/P+1 prescaler |
| Charge Pump | Precision charge pump with external loop filter | Precision charge pump with external loop filter | Precision charge pump with external loop filter | Precision charge pump with external loop filter | Precision charge pump with external loop filter |
| Power-Supply Options | Single nominal supply architecture | Single nominal supply architecture | Single nominal supply architecture | Single nominal supply architecture | HV power-supply options |
Bảo phân biệt quan trọng
- Matches the 550 MHz class without extending into higher RF-frequency envelopes (vsADF4111BCPZ)
- Uses the common 20-lead WFQFN exposed-pad family footprint (vsADF4112BCPZ)
- Shares the integrated integer-N PLL architecture (vsADF4113BCPZ)
Ghi chú thiết kế
Calculate the charge-pump current setting from the RSET resistor value and the manufacturer’s specified relationship rather than copying a value from another board. Confirm the complete supply topology, decoupling capacitance, voltage tolerance, and startup sequence against the ADF4110 family data sheet, Revision F. The charge-pump supply and analog supply paths should be decoupled locally to prevent reference or phase-detector noise from coupling into the loop filter.
Place the loop-filter network and its grounding return close to the CP, COM, and RSET pins. Keep the exposed pad connected to a continuous ground plane with multiple thermal and electrical vias where the package drawing permits. Route the PFD and prescaler feedback paths away from the CP node and reference input to reduce coupling. Confirm the final land pattern against the official WFQFN package dimensions rather than scaling it from a generic QFN footprint.
Do not reuse loop-filter values when changing the prescaler, reference frequency, or integer-N division ratio. The same filter can produce different phase margin, lock range, settling time, and reference-spur behavior as those parameters change. Calculate the filter for the worst-case operating channel and validate acquisition on hardware. Also verify that firmware writes the complete register set for the selected alternative rather than relying only on similar package dimensions.
Keep the reference input and RF prescaler path away from the charge-pump output and high-impedance loop-filter nodes. Use a controlled reference source with low phase noise because reference multiplication can dominate close-in synthesizer noise. Provide adequate ground shielding around the loop filter and avoid long parallel copper routes between sensitive nodes. Scope the lock behavior across temperature and supply corners when tuning the filter for production margin.
Thông tin tuân thủ
The ADF4110 product page identifies the family as production status. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not stated in the cited summaries and therefore remain unknown.