Analog Devices

ADF4110BCPZ-RL7 - 550 MHz Integer-N PLL | Analog Devices

MPN: ADF4110BCPZ-RL7 ✓ Aktif
20-lead WFQFN with exposed pad Package 550 MHz Speed
MOQ: 1 |

ADF4110BCPZ-RL7 Ringkasan

The Analog Devices ADF4110BCPZ-RL7 is a single, integer-N phase-locked loop frequency synthesizer with a maximum RF input frequency of 550 MHz, programmable prescaler and charge pump, and a 20-lead WFQFN exposed-pad package. It is designed to generate stable local-oscillator signals in RF receivers, transmitters, instrumentation, and wireless communication systems.

A phase-locked loop, or PLL, is a frequency-control circuit that compares a divided reference signal with a feedback signal and drives a phase error toward zero through feedback. The ADF4110 belongs to the broader hierarchy of frequency synthesizer, clock-generation IC, timing-control integrated circuit, and semiconductor categories. Its integer-N architecture simplifies frequency planning while supporting programmable division ratios for RF channel selection.

The device includes a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, 6-bit A counter, 13-bit B counter, and dual-modulus prescaler. Together, these blocks support programmable frequency synthesis while providing the phase-detection and current-pump functions required by an external passive loop filter. The manufacturer describes the part as production status, and the data sheet is identified as Revision F.

At the circuit level, the ADF4110 family combines a prescaler with programmable A and B counters to produce division ratios for wireless receiver and transmitter local oscillators. The charge-pump output drives an external loop filter, whose component values determine loop bandwidth, reference-spur behavior, phase noise, and settling performance. This architecture favors predictable integer-N implementation when a direct fractional-N synthesizer is not required.

Typical uses include RF local oscillators in wireless receivers and transmitters, frequency-agile communications equipment, industrial RF test systems, and signal-generation instruments. The 550 MHz maximum RF input frequency makes the device particularly relevant to RF front ends operating below 600 MHz, including industrial, scientific, instrumentation, and selected communication bands.

Layout and loop-filter design are critical. Place the charge-pump output and loop-filter components close to the device, provide a low-impedance ground and exposed-pad connection, decouple the supply near the pins, and route high-frequency feedback lines away from sensitive analog nodes. The external loop filter must be calculated against the intended reference frequency, prescaler, division ratio, and phase-noise requirement.

This product page combines the manufacturer’s device specifications with application guidance, package information, practical design notes, and a parameter comparison of related ADF4110-family synthesizers. The comparison focuses on package fit and functional differences so engineers can determine whether a related member is appropriate before changing an RF board design.

Alternatif penggantian untuk ADF4110BCPZ-RL7 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian ADF4110BCPZ-RL7 (sama faktor bentuk dan footprint) — berbeda di dalam Product Type, Architecture, Charge Pump, Prescaler, Package.

Analog Devices
Product Type: RF PLL frequency synthesizer
Charge Pump: Precision type
Bandingkan dengan ADF4110BCPZ-RL7 →
Analog Devices
Product Type: Integer-N RF PLL frequency synthesizer
Architecture: Single integer-N PLL
Charge Pump: Programmable current
Bandingkan dengan ADF4110BCPZ-RL7 →
Analog Devices
Prescaler: Programmable dual-modulus P/P+1
Package: 20-lead LFCSP with exposed pad
Bandingkan dengan ADF4110BCPZ-RL7 →
Analog Devices
Product Type: Integer-N frequency synthesizer
Architecture: Integer-N PLL
Prescaler: Dual-modulus P/P+1
Bandingkan dengan ADF4110BCPZ-RL7 →

ADF4111BCPZ

✅ Drop-In
Analog Devices
📦 20-WFQFN Exposed Pad
RF PLL frequency synthesizer · 1.4 GHz · 1.2 GHz · 1 · Yes · Dual-modulus P/P+1 · 6 bit · 13 bit

Kontak untuk harga

Lihat Datasheet →

ADF4112BCPZ

✅ Drop-In
Analog Devices
📦 20-WFQFN Exposed Pad
Integer-N RF PLL frequency synthesizer · 3 GHz · 4 GHz · 5 MHz to 3 GHz · 3.3 V · CMOS or TTL · Clock · Single integer-N PLL

Kontak untuk harga

Lihat Datasheet →

ADF4113BCPZ

✅ Drop-In
Analog Devices
📦 20-WFQFN Exposed Pad
Single integer-N RF PLL frequency synthesizer · 4 GHz · 5 MHz · 165 MHz · Integer-N · 1 · 6 bits · 13 bits

Kontak untuk harga

Lihat Datasheet →

ADF4113HVBCPZ

✅ Drop-In
Analog Devices
📦 20-WFQFN Exposed Pad
Integer-N frequency synthesizer · 4 GHz · 15 V · Up to 15 V · Integer-N PLL · Digital phase-frequency detector · Dual-modulus P/P+1 · 6 bits

Kontak untuk harga

Lihat Datasheet →

ADF4110BCPZ-RL7 Spesifikasi

Product Type Single integer-N RF PLL frequency synthesizer
Maximum RF Input Frequency 550 MHz
Architecture Integer-N phase-locked loop
Prescaler Programmable dual-modulus P/P+1 prescaler
A Counter 6-bit programmable counter
B Counter 13-bit programmable counter
Reference Divider Programmable divider
Phase Detector Low-noise digital phase-frequency detector
Charge Pump Precision charge-pump output with external loop filter
Paket 20-lead WFQFN with exposed pad
Package Pin Count 20 pins including exposed pad
Tipe Mounting Surface mount
Manufacturer Lifecycle Status Production

Konfigurasi Pin ADF4110BCPZ-RL7

QFN-20 Package Pinout Diagram QFN-20 4x4mm, P0.5mm, EP 2.5x2.5mm, JEDEC MO-220. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 QFN-20
Pin produk 1 VDD — Analog and digital supply input
Pin produk 2 COM — Charge-pump and loop-filter common connection
Pin produk 3 OUT — Prescaler output for the phase-frequency detector
Pin produk 4 RSET — Charge-pump current-setting resistor connection
Pin produk 5 GND — Analog and digital ground
Pin produk 6 REFin — Reference input complementary connection
Pin produk 7 REFin+ — Reference input
Pin produk 8 DATA — Serial programming data input
Pin produk 9 LE — Serial programming latch enable
Pin produk 10 CE — Serial programming chip enable
Pin produk 11 DB0 — Data bus bit 0
Pin produk 12 DB1 — Data bus bit 1
Pin produk 13 DB2 — Data bus bit 2
Pin produk 14 DB3 — Data bus bit 3
Pin produk 15 DB4 — Data bus bit 4
Pin produk 16 DB5 — Data bus bit 5
Pin produk 17 PFD — Phase-frequency detector output
Pin produk 18 CP — Charge-pump output driving the external loop filter
Pin produk 19 SW — Analog and digital ground connection
Pin produk 20 EP — Exposed pad connected to ground

Aplikasi Umum

ADF4110BCPZ-RL7 cocok untuk 6 aplikasis: Wireless Receiver Local Oscillator, Wireless Transmitter Frequency Synthesizer, Industrial RF Test Instrument, Frequency-Selective Receiver, Communications Signal Generator, Low-Cost RF Frequency Synthesizer.

🌐

Wireless Receiver Local Oscillator

The ADF4110BCPZ-RL7 fits a wireless receiver local-oscillator block operating below the device’s 550 MHz RF input limit. Its programmable prescaler, 6-bit A counter, 13-bit B counter, and reference divider allow the synthesizer to derive an LO channel plan from a stable reference. A digital phase-frequency detector and precision charge pump drive an external passive loop filter. Compared with a fixed-frequency oscillator, this architecture permits channel changes without redesigning the RF front end. The key trade-off is loop-filter complexity: component values must be selected for the intended prescaler, division ratio, phase-noise target, and settling requirement.

📡

Wireless Transmitter Frequency Synthesizer

The ADF4110BCPZ-RL7 can provide a programmable RF source for wireless transmitter up-conversion and down-conversion stages within its 550 MHz maximum input-frequency range. The integer-N divider chain and programmable reference divider support flexible channel selection, while the charge-pump output permits optimization of phase noise and reference spurs through the external loop filter. In transmit systems, stable reference-clock quality and loop-filter phase margin are especially important because excessive reference multiplication or an unsuitable bandwidth can degrade close-in phase noise and adjacent-channel performance.

🏭

Industrial RF Test Instrument

The ADF4110BCPZ-RL7 is suitable for industrial RF test equipment that generates or receives programmable signals below 550 MHz. Its programmable prescaler and counter architecture supports multiple test frequencies from a shared reference, while integer-N operation simplifies calibration and channel planning. The external loop filter provides a direct way to balance acquisition time against phase noise and spurious performance for the intended test bandwidth. For production instruments, account for reference-clock drift, temperature-dependent calibration, shield isolation, and the possibility of accumulated reference-multiplier phase noise when selecting the loop bandwidth.

📻

Frequency-Selective Receiver

The ADF4110BCPZ-RL7 can support frequency-selective receiver architectures in which a programmable LO tracks a selected channel. The reference divider and A/B counters establish the required integer-N ratio, while the phase-frequency detector and charge pump continuously correct the VCO. This arrangement is useful when several bands must be covered without changing the complete receiver architecture. A critical design consideration is ensuring that every divider combination supports the target RF input and that the loop filter maintains adequate phase margin across the selected prescaler modes and channel ratios.

🖥️

Communications Signal Generator

The ADF4110BCPZ-RL7 is appropriate for compact communications signal-generation modules that require programmable RF frequency synthesis with a maximum input frequency of 550 MHz. The integer-N architecture gives the controller direct access to the prescaler, reference divider, and A/B counters, allowing deterministic frequency setup. Designers should derive the loop-filter values from the selected reference and channel plan rather than reuse a generic component set. The result can be a low-component-count local oscillator suitable for embedded test fixtures, communication panels, and compact laboratory modules.

⚡

Low-Cost RF Frequency Synthesizer

The ADF4110BCPZ-RL7 offers a practical way to build a low-cost RF frequency synthesizer below 550 MHz because the prescaler, counters, phase detector, and charge pump are integrated into one IC. Only the loop filter and external VCO are required for the core synthesizer function. This integration reduces board area and firmware complexity compared with discrete divider and comparator approaches. The principal limitation is that integer-N architecture can increase reference spurs when a high division ratio is used, so the reference frequency, loop bandwidth, and output-frequency plan should be optimized together.

What is the ADF4110BCPZ-RL7?
The ADF4110BCPZ-RL7 is a single integer-N RF phase-locked-loop frequency synthesizer with a maximum RF input frequency of 550 MHz. According to the Analog Devices ADF4110 family data sheet, Revision F, it combines a programmable prescaler, charge pump, reference divider, 6-bit A counter, and 13-bit B counter in a 20-lead WFQFN package with an exposed pad.
What is the operating voltage of the ADF4110BCPZ-RL7?
The exact supply-voltage limits are not stated in the product-page summary, so consult the recommended operating conditions in the Analog Devices ADF4110 family data sheet, Revision F, before designing the power rail. The device includes supply and ground pins that must be decoupled according to the manufacturer’s application guidance. Confirm the full supply range, supply-current limits, and absolute maximum ratings during schematic review.
Where can I download the ADF4110BCPZ-RL7 datasheet PDF?
The official ADF4110BCPZ-RL7 data sheet can be obtained from Analog Devices through the ADF4110 family data-sheet link on this page. The manufacturer identifies the document as Revision F and provides the full ADF4110, ADF4111, ADF4112, and ADF4113 data sheet. Use the pin-description table, register map, loop-filter guidance, and recommended application circuit when laying out the board.
Where is the ADF4110BCPZ-RL7 pinout?
The pinout is shown in the manufacturer’s ADF4110 family data sheet, Revision F, using the 20-lead WFQFN exposed-pad package associated with the BCPZ designation. The exposed pad is a thermal and electrical connection rather than an ordinary signal lead. Assign PCB nets from the official pin-description table and confirm exposed-pad clearance and solder-joint design against the package drawing.
What are the key specifications of ADF4110BCPZ-RL7 that engineers should know?
The principal specifications are a 550 MHz maximum RF input frequency, integer-N PLL architecture, programmable dual-modulus prescaler, programmable reference divider, 6-bit A counter, 13-bit B counter, low-noise digital phase-frequency detector, and precision charge pump. The Analog Devices data sheet, Revision F, also identifies a single-channel device in a 20-lead WFQFN exposed-pad package.
How is the ADF4110BCPZ-RL7 used in an RF local oscillator?
The ADF4110BCPZ-RL7 can divide a programmable RF input through its prescaler and A/B counters, compare the divided signal with a divided reference, and adjust the voltage-controlled oscillator through the charge pump and external loop filter. According to the Analog Devices data sheet, the family is intended for local oscillators in wireless receiver and transmitter up-conversion and down-conversion sections.
What is the best drop-in replacement for ADF4110BCPZ-RL7?
The closest verified drop-in candidates are members of the same Analog Devices ADF4110 family that use the same 20-lead WFQFN footprint, including ADF4111BCPZ, ADF4112BCPZ, ADF4113BCPZ, and ADF4113HVBCPZ. No cross-manufacturer drop-in replacement was confirmed. Verify register compatibility, RF-frequency range, prescaler settings, interface timing, and loop-filter calculations before substitution.
Can ADF4111BCPZ replace ADF4110BCPZ-RL7?
ADF4111BCPZ can be considered a board-level drop-in candidate because it belongs to the same ADF411x family and uses the same 20-lead WFQCN package, but its higher RF-frequency capability changes the functional envelope. It is not an unconditional substitute: compare the required RF input frequency, prescaler range, register map, reference-divider behavior, and external loop-filter settings against the original design.
ADF4110BCPZ-RL7 vs ADF4153BCPZ — which is better for RF synthesis?
ADF4110BCPZ-RL7 is preferable when the design specifically targets its integer-N architecture, 550 MHz RF input limit, and existing ADF4110 register and loop-filter design. ADF4153BCPZ is a different synthesizer family whose RF range, prescaler structure, register map, and loop-filter requirements differ, so it should not be treated as a transparent drop-in replacement. Use the manufacturer data sheets for both devices to compare channel-plan requirements.
When should I choose ADF4110BCPZ-RL7 over ADF4113BCPZ?
Choose ADF4110BCPZ-RL7 when the RF signal and required prescaler operation remain within its 550 MHz maximum input frequency and when reusing an existing ADF4110-based board layout, firmware, and loop-filter design is valuable. Choose ADF4113BCPZ when a higher-frequency RF plan or additional family functionality is required, after confirming that its interface, register set, and output behavior meet the system specification.
Is ADF4110BCPZ-RL7 suitable for industrial RF instrumentation?
The ADF4110BCPZ-RL7 is suitable for many RF instrumentation and test applications below its 550 MHz maximum RF input frequency because it provides programmable integer-N synthesis, a programmable prescaler, and an external charge-pump loop-filter architecture. For industrial deployment, verify operating-temperature limits, supply tolerances, reference-clock accuracy, phase-noise targets, calibration needs, and long-term stability in the final instrument.
What design considerations matter for the ADF4110BCPZ-RL7 loop filter?
The loop filter is the central design element because its resistance, capacitance, charge-pump current, and phase margin determine lock behavior, phase noise, reference spurs, and settling time. Calculate it using the intended reference frequency, prescaler, A and B division values, target loop bandwidth, and phase-noise requirements. The Analog Devices family data sheet provides the topology and calculation guidance needed for a defensible design.
How should the ADF4110BCPZ-RL7 PCB be laid out?
Place the loop-filter components close to the charge-pump output, keep the charge-pump and feedback paths compact, and connect the exposed pad to the ground plane with adequate thermal and electrical vias. Decouple the supply at the device pins and route high-frequency RF and feedback tracks away from sensitive low-frequency nodes. Follow the recommended application circuit and package land pattern in the manufacturer documentation.
Where can I buy the ADF4110BCPZ-RL7 and check stock?
Use the Request a Quote form on this page to request current availability, volume pricing, and lead time for ADF4110BCPZ-RL7. The form allows buyers to specify quantities and packaging requirements without relying on a static listing that may be out of date. Confirm the exact MPN, 20-lead WFQCN configuration, reel quantity, and delivery terms in the quotation response.
What is the lead time for ADF4110BCPZ-RL7?
The current lead time for ADF4110BCPZ-RL7 should be confirmed through the Request a Quote form on this page. Lead time can vary with order quantity, scheduled factory allocation, packaging configuration, and current component availability. Include the required quantity and target delivery date in the request so the supplier can confirm the most relevant production and logistics information.
Is the ADF4110BCPZ-RL7 currently in production?
The Analog Devices product page identifies the ADF4110 as having production status. That status indicates the manufacturer continues to present the family as a current product rather than an obsolete or discontinued offering. For a new procurement, request a written confirmation of availability and lifecycle terms for the exact ADF4110BCPZ-RL7 order code through the Request a Quote form.

Data referensi engineering untuk ADF4110BCPZ-RL7 — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose ADF4110BCPZ-RL7 for an integer-N RF design whose prescaled input remains within 550 MHz and for which an established ADF4110 control, register, and loop-filter approach is valuable. ADF4111BCPZ is appropriate when a broader 1.2 GHz RF envelope is useful but still requires all divider, prescaler, and filter settings to be reviewed. ADF4112BCPZ and ADF4113BCPZ are better choices for substantially higher-frequency plans because they reach 3.0 GHz and 4.0 GHz, respectively. ADF4113HVBCPZ should be selected when its alternate supply architecture matches the system better. All listed candidates share the 20-lead WFQFN exposed-pad format, but common packaging does not guarantee common register behavior. Final selection must include a line-by-line comparison of RF limits, prescaler modes, reference-divider behavior, programming interface, loop-filter formulas, and acquisition performance.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini ADF4111BCPZ ADF4112BCPZ ADF4113BCPZ ADF4113HVBCPZ
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package 20-WFQFN Exposed Pad 20-WFQFN Exposed Pad 20-WFQFN Exposed Pad 20-WFQFN Exposed Pad 20-WFQFN Exposed Pad
Maximum RF Input Frequency 550 MHz 1.2 GHz 3.0 GHz 4.0 GHz 4.0 GHz
PLL Architecture Single integer-N PLL Single integer-N PLL Single integer-N PLL Single integer-N PLL Single integer-N PLL
A Counter 6-bit programmable 6-bit programmable 6-bit programmable 6-bit programmable 6-bit programmable
B Counter 13-bit programmable 13-bit programmable 13-bit programmable 13-bit programmable 13-bit programmable
Prescaler Programmable dual-modulus P/P+1 prescaler Programmable dual-modulus P/P+1 prescaler Programmable dual-modulus P/P+1 prescaler Programmable dual-modulus P/P+1 prescaler Programmable dual-modulus P/P+1 prescaler
Charge Pump Precision charge pump with external loop filter Precision charge pump with external loop filter Precision charge pump with external loop filter Precision charge pump with external loop filter Precision charge pump with external loop filter
Power-Supply Options Single nominal supply architecture Single nominal supply architecture Single nominal supply architecture Single nominal supply architecture HV power-supply options

Diferensiator Kunci

  • Matches the 550 MHz class without extending into higher RF-frequency envelopes (vsADF4111BCPZ)
  • Uses the common 20-lead WFQFN exposed-pad family footprint (vsADF4112BCPZ)
  • Shares the integrated integer-N PLL architecture (vsADF4113BCPZ)

Catatan Desain

Calculate the charge-pump current setting from the RSET resistor value and the manufacturer’s specified relationship rather than copying a value from another board. Confirm the complete supply topology, decoupling capacitance, voltage tolerance, and startup sequence against the ADF4110 family data sheet, Revision F. The charge-pump supply and analog supply paths should be decoupled locally to prevent reference or phase-detector noise from coupling into the loop filter.

Place the loop-filter network and its grounding return close to the CP, COM, and RSET pins. Keep the exposed pad connected to a continuous ground plane with multiple thermal and electrical vias where the package drawing permits. Route the PFD and prescaler feedback paths away from the CP node and reference input to reduce coupling. Confirm the final land pattern against the official WFQFN package dimensions rather than scaling it from a generic QFN footprint.

Do not reuse loop-filter values when changing the prescaler, reference frequency, or integer-N division ratio. The same filter can produce different phase margin, lock range, settling time, and reference-spur behavior as those parameters change. Calculate the filter for the worst-case operating channel and validate acquisition on hardware. Also verify that firmware writes the complete register set for the selected alternative rather than relying only on similar package dimensions.

Keep the reference input and RF prescaler path away from the charge-pump output and high-impedance loop-filter nodes. Use a controlled reference source with low phase noise because reference multiplication can dominate close-in synthesizer noise. Provide adequate ground shielding around the loop filter and avoid long parallel copper routes between sensitive nodes. Scope the lock behavior across temperature and supply corners when tuning the filter for production margin.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The ADF4110 product page identifies the family as production status. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not stated in the cited summaries and therefore remain unknown.

Data disahkan pada: 2026-11-20 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

ADF4110BCPZ-RL7 ADF4110BCPZ-RL7 datasheet ADF4110BCPZ-RL7 datasheet pdf ADF4110BCPZ-RL7 pinout Analog Devices ADF4110BCPZ-RL7 ADF4110BCPZ-RL7 550 MHz ADF4110BCPZ-RL7 equivalent ADF4110BCPZ-RL7 replacement ADF4110BCPZ-RL7 cross reference ADF4110BCPZ-RL7 vs ADF4111BCPZ ADF4110BCPZ-RL7 vs ADF4113BCPZ ADF4110BCPZ-RL7 WFQFN footprint ADF4110BCPZ-RL7 price ADF4110BCPZ-RL7 stock ADF4110 integer-N PLL application circuit

Komponen dan Istilah Terkait

Analog Devices ADF4110BCPZ-RL7 ADF4110 ADF4111BCPZ ADF4112BCPZ ADF4113BCPZ ADF4113HVBCPZ integer-N PLL phase-locked loop frequency synthesizer clock generator phase-frequency detector charge pump dual-modulus prescaler programmable reference divider 6-bit A counter 13-bit B counter RF local oscillator wireless receiver wireless transmitter 20-lead WFQFN exposed pad loop filter surface-mount semiconductor
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ