ADF4110BRUZ-RL7 - 550MHz Integer-N PLL | Analog Devices
MPN: ADF4110BRUZ-RL7 ✓ Hoạt độngADF4110BRUZ-RL7 Tóm tắt
A PLL frequency synthesizer is a timing and frequency-control IC that locks an output frequency to a stable reference. Its hierarchy extends from RF clock and frequency synthesizer to phase-locked loop, clock-generation IC, and power-management-independent signal-chain device. The ADF4110 family supports wireless receiver and transmitter local oscillators by combining a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, 6-bit A counter, 13-bit B counter, and dual-modulus P/P+1 prescaler.
Key features include the 550 MHz maximum synthesizer frequency, integer-N architecture, programmable prescaler, programmable A and B counters, and a programmable reference divider. The charge-pump and phase-frequency detector support closed-loop frequency generation, while the counters establish the required multiplication ratio. These functions make the ADF4110 suitable for RF local-oscillator generation, modulation and demodulation systems, wireless transceiver tuning, and precision test equipment.
The ADF4110BRUZ-RL7 is identified as a production device by Analog Devices. Its 16-TSSOP package supports compact surface-mount layouts, although the relatively narrow package requires careful fanout from the fine-pitch leads. The suffix identifies the specific orderable package, temperature, and reel configuration; the manufacturer product page and family datasheet should be used for final manufacturing and lot-control requirements.
Typical applications include GSM and other wireless receiver local oscillators, wireless transmitter up-conversion and down-conversion paths, industrial RF test equipment, and instrumentation requiring programmable synthesized RF. In these systems, a crystal oscillator or TCXO can provide the reference signal, while the ADF4110 produces a programmable output locked to that reference for coherent mixing or channel selection.
PCB design should keep the reference, charge-pump, and RF feedback paths compact and away from noisy switching nodes. Confirm loop-filter component values, prescaler selection, counter limits, and allowable operating regions against the manufacturer datasheet before tuning. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks, and preserve the specified decoupling and grounding layout to minimize phase noise and spurious signals.
Bộ thay thế dễ dàng lắp đặt cho ADF4110BRUZ-RL7 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADF4110BRUZ-RL7 (cùng hình factor và footprint) — khác nhau ở Prescaler, Package, Product Type, A Counter, B Counter.
ADF4111BRUZ-RL7
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADF4112BRUZ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADF4113BRUZ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADF4116BRUZ-REEL7
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADF4107BRU-REEL
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADF4110BRUZ-RL7 Thông số kỹ thuật
| Product Type | Single integer-N RF PLL frequency synthesizer |
| Maximum RF Input Frequency | 550 MHz |
| Architecture | Integer-N phase-locked loop |
| Number of Channels | 1 channel |
| A Counter Width | 6 bits |
| B Counter Width | 13 bits |
| Prescaler | Programmable dual-modulus P/P+1 |
| Reference Divider | Programmable |
| Phase Detector | Low-noise digital phase-frequency detector |
| Charge Pump | Precision charge pump |
| Hộp | 16-TSSOP, 4.40 mm width |
| Package Lead Width | 0.173 inch |
| Nhiệt độ hoạt động | -40 °C to +85 °C |
| Kiểu lắp đặt | Surface mount |
| Production Status | Production |
Hướng dẫn cấu hình chân ADF4110BRUZ-RL7 0.173 inch
Cấu hình chân cho ADF4110BRUZ-RL7 (0.173 inch gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ADF4110BRUZ-RL7.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ADF4110BRUZ-RL7 phù hợp cho 6 Áp dụngs: Wireless Receiver Local Oscillator, Wireless Transmitter Frequency Generation, RF Test and Measurement Instrument, GSM Receiver Frequency Plan, Industrial RF Control and Monitoring, Frequency-Synchronized Instrumentation.
Wireless Receiver Local Oscillator
The ADF4110BRUZ-RL7 is suitable for generating a programmable local-oscillator signal in wireless receiver front ends. Its integer-N PLL combines a phase-frequency detector, precision charge pump, programmable reference divider, 6-bit A counter, 13-bit B counter, and dual-modulus prescaler to translate a stable reference into the required RF channel. The 550 MHz maximum input frequency defines the upper RF planning boundary. In an up-conversion or down-conversion path, the synthesized signal can drive a mixer while remaining phase-locked to the system reference. Designers should select the prescaler and counter values that satisfy the target channel plan, then validate lock range, reference spurs, and phase noise on the final reference and loop-filter implementation.
Được đề xuất
Wireless Transmitter Frequency Generation
The ADF4110BRUZ-RL7 can provide the programmable frequency source required by wireless transmitter signal chains. Placing the PLL upstream of a mixer or up-conversion stage allows the carrier to be derived coherently from a shared reference rather than from an independent resonator. The device's 550 MHz maximum RF input frequency and programmable dual-modulus prescaler support integer-N channel planning, while the 6-bit A and 13-bit B counters establish the multiplication ratio. For transmitter designs, phase noise and reference spurs can affect modulation quality and adjacent-channel performance, so loop-filter tuning, reference-source isolation, PCB return paths, and conducted/radiated emissions must be evaluated together rather than relying on nominal register settings alone.
Được đề xuất
RF Test and Measurement Instrument
The ADF4110BRUZ-RL7 is appropriate for programmable RF test equipment that requires an accurate synthesized source with multiple channel selections. A reference oscillator can feed the PLL, and the integer-N architecture can generate the local-oscillator frequency required by a receiver test, mixer test, or signal-generation block. The 550 MHz RF limit provides a clear boundary for test-plan planning, while the programmable reference divider and counters allow multiple division and multiplication ratios. Instrument designers should account for reference purity, loop bandwidth, calibration, and settling time. A representative implementation should use short RF feedback tracks, a compact loop filter, and a layout that prevents digital-control return current from coupling into the reference or prescaler nodes.
Được đề xuất
GSM Receiver Frequency Plan
The ADF4110BRUZ-RL7 can support the programmable local oscillator required in GSM receiver architectures. The ADF4110 family documentation explicitly describes use in wireless receiver and transmitter local oscillators, and its programmable reference divider, counters, and dual-modulus prescaler allow a common reference to be translated into channel-specific RF frequencies. The target's 550 MHz maximum input frequency must be checked against every intermediate frequency and prescaler operating point in the receiver plan. Designers should also evaluate phase noise, lock time, reference spurs, and acquisition margin under the required temperature range. The family datasheet's reference-input and application guidance should form the basis of the PCB layout and component-selection review.
Được đề xuất
Industrial RF Control and Monitoring
The ADF4110BRUZ-RL7 can serve as the programmable RF element in an industrial monitoring or control system that performs coherent mixing, interrogation, or frequency-selective measurement. Its integer-N topology gives the controller a deterministic relationship between a stable reference and the selected RF output, while the programmable counters and prescaler support multiple operating channels. The 550 MHz maximum frequency should be treated as an upper RF constraint rather than a guarantee that every desired plan is achievable with one prescaler. Engineering validation should cover reference jitter, loop-filter behavior, output buffering, PCB isolation, and stable operation from -40 °C to +85 °C. Digital programming lines should be routed away from sensitive analog nodes to reduce coupling into the feedback divider.
Được đề xuất
Frequency-Synchronized Instrumentation
The ADF4110BRUZ-RL7 is useful in instrumentation that must derive multiple RF-related frequencies from one stable reference. A laboratory or industrial instrument can program the reference divider, A counter, B counter, and prescaler to establish a repeatable synthesis ratio, reducing reliance on separate free-running oscillators. Its 550 MHz RF input ceiling supports designs within that range, while the phase-frequency detector and precision charge pump establish the PLL's control loop. Practical implementation requires a reference source with adequate phase noise and low ripple, a carefully calculated loop filter, and controlled grounding around the feedback network. Engineers should measure phase noise, reference spurs, lock behavior, and temperature drift across the operating range before using the output for precision measurement.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADF4110BRUZ-RL7 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADF4111BRUZ-RL7 | ADF4112BRUZ | ADF4113BRUZ | ADF4116BRUZ-REEL7 | ADF4107BRU-REEL |
|---|---|---|---|---|---|---|
| Package | 16-TSSOP, 4.40 mm width | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| PLL Architecture | Integer-N | Integer-N | Integer-N | Integer-N | Integer-N | Integer-N |
| Number of Channels | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel |
| Special Features | Programmable reference divider, A counter, B counter, and prescaler | Programmable frequency-synthesis functions | Programmable frequency-synthesis functions | Programmable frequency-synthesis functions | Programmable frequency-synthesis functions | Programmable frequency-synthesis functions |
Bảo phân biệt quan trọng
- 550 MHz maximum RF input frequency (vsADF4116BRUZ-REEL7)
- Defined 6-bit A counter and 13-bit B counter (vsADF4112BRUZ)
- Programmable reference divider and dual-modulus prescaler (vsADF4107BRU-REEL)
- Production status with a documented 550 MHz family member (vsADF4111BRUZ-RL7)
Ghi chú thiết kế
Keep the reference input, prescaler feedback, RF input, and loop-filter connections short and compact. The 16-TSSOP body is only 4.40 mm wide, so fanout routing can increase parasitic inductance and coupling between the feedback divider, charge pump, and digital programming lines. Use a stable ground reference, place input and output decoupling according to the manufacturer layout, and keep switching-node copper away from the sensitive reference and feedback paths. Review the final assembly for exposed-package and lead-clearance constraints before releasing the fabrication data.
Plan the loop filter around the actual reference frequency, target channel, prescaler, phase-detector gain, charge-pump current, and required settling time. A narrow loop can reduce reference-spur energy but may slow acquisition, while a wider loop can improve capture behavior yet increase integrated phase noise. Validate both lock behavior and spectral purity using the final reference source, charge-pump settings, divider layout, and PCB parasitics. Compare the measured output against the phase-noise and spur limits of the receiver, transmitter, or instrument being developed.
Do not select a replacement solely because it uses a 16-TSSOP package. Before substituting ADF4111BRUZ-RL7, ADF4112BRUZ, ADF4113BRUZ, ADF4116BRUZ-REEL7, or ADF4107BRU-REEL, verify maximum RF frequency, prescaler values, reference-divider range, counter limits, register behavior, and electrical limits. A valid footprint match still requires a valid frequency plan. Also confirm the exact reel suffix and temperature grade so the approved part matches the original assembly documentation.
Separate high-speed digital programming activity from the reference and feedback network. Route the charge-pump return and sensitive analog ground through a low-impedance path rather than relying on fragmented plane currents. Place loop-filter components close to their associated device pins and use component orientations that minimize loop area. After assembly, inspect the reference and RF output for unexpected harmonics, periodic spurs, and sensitivity to nearby digital activity; these tests often reveal grounding or return-path errors more effectively than a static schematic review.
Thông tin tuân thủ
Analog Devices identifies the ADF4110 as a production device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for the exact ADF4110BRUZ-RL7 orderable MPN were not established by the available manufacturer page excerpt.