ADF5002BCPZ-RL7 - 18 GHz Divide-by-8 RF Prescaler | Analog Devices
MPN: ADF5002BCPZ-RL7 ✓ Hoạt độngADF5002BCPZ-RL7 Tóm tắt
An RF prescaler is a frequency-divider block used at the input of a PLL frequency synthesizer. It reduces a high-frequency reference signal by a fixed ratio so that the synthesizer’s phase detector and feedback divider can operate within a more practical frequency range. In this architecture, the ADF5002BCPZ-RL7 belongs to the clock and timing IC hierarchy and serves as the high-frequency divide-by-8 stage preceding PLL circuits such as the ADF4156 or ADF4106.
The principal functional specifications are an 18 GHz maximum input frequency, fixed divide ratio of 8, and 3.3 V power supply. The Analog Devices ADF5002 datasheet also specifies differential 100 Ω RF outputs and an operating temperature range of −40°C to +105°C. These characteristics make the part suitable for RF test equipment, microwave communication chains, instrumentation, and frequency-generation systems that require division of microwave-frequency signals without adding another adjustable divider function.
Because the ADF5002 is a fixed divider, its output frequency is the input frequency divided by 8. For example, an 8 GHz input produces a 1 GHz divided output. The RF output interface is differential rather than single-ended, which can simplify connection to suitable balanced PLL inputs and help preserve signal integrity when the PCB interconnects are controlled carefully. The device is intended for low-noise, low-power operation, as described in the manufacturer documentation.
Typical applications include microwave PLL reference paths, RF instrument local-oscillator chains, satellite and microwave communication test equipment, and low-noise RF signal conditioning. The manufacturer specifically identifies the ADF4156 and ADF4106 as suitable downstream PLL ICs. Designers should verify the PLL’s prescaler-input range, allowable input power, impedance requirements, and reference-noise contribution before finalizing the interface.
PCB implementation requires close attention to the exposed thermal and electrical pad, supply decoupling, high-speed RF routing, and grounding. The RF input and differential output paths should use controlled-impedance routing and short connections, with via transitions minimized. The 3.3 V supply network should include local decoupling close to the device, and the exposed pad should be connected to the ground plane according to the manufacturer’s land-pattern and assembly guidance.
This page combines the manufacturer’s device description, package and operating information, sourcing data, comparison fields, and application-focused engineering guidance. It is intended to help engineers identify the correct RF divider, validate its PLL interface, and plan layout without treating a functional similarity as proof of pin-to-pin substitutability.
Bộ thay thế dễ dàng lắp đặt cho ADF5002BCPZ-RL7 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADF5002BCPZ-RL7 (cùng hình factor và footprint) — khác nhau ở Package, Product Type.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếADF5002BCPZ-RL7 Thông số kỹ thuật
| Product Type | Fixed RF prescaler |
| Divide Ratio | 8:1 |
| Maximum Input Frequency | 18 GHz |
| Điện áp cung cấp | 3.3 V |
| Supply Voltage Tolerance | ±10% |
| RF Output Configuration | Differential |
| RF Output Impedance | 100 Ω differential |
| Khoảng nhiệt độ hoạt động | −40°C to +105°C |
| Hộp | 16-lead WFQFN CSP with exposed pad |
| Nominal Package Dimensions | 3 mm × 3 mm |
| Kiểu lắp đặt | Surface mount |
| Input Signal | Single-ended RF input |
| Output Signal | Differential RF output |
| Trạng thái RoHS | Compliant |
| AEC-Q100 Qualification | Not applicable |
Hướng dẫn cấu hình chân ADF5002BCPZ-RL7 3 mm × 3 mm
Cấu hình chân cho ADF5002BCPZ-RL7 (3 mm × 3 mm gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ADF5002BCPZ-RL7.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ADF5002BCPZ-RL7 phù hợp cho 6 Áp dụngs: Microwave PLL Reference Divider, RF Test and Measurement Equipment, Microwave Communication Signal Conditioning, Low-Phase-Noise Frequency Generation, Instrumentation and Calibration Loops, RF Frequency Divider Subsystem.
Microwave PLL Reference Divider
The ADF5002BCPZ-RL7 fits at the RF input of a PLL synthesizer because it divides signals as high as 18 GHz by a fixed factor of 8 while operating from a 3.3 V supply. For example, an 8 GHz input becomes a 1 GHz signal suitable for a compatible PLL prescaler input. The differential 100 Ω output helps maintain a balanced RF path, but the selected PLL must support the resulting frequency, signal level, impedance, and noise contribution. This use should be validated with the PLL’s input-referred phase-noise requirements rather than frequency compatibility alone.
Được đề xuất
RF Test and Measurement Equipment
The ADF5002BCPZ-RL7 is useful in microwave test equipment that needs a clean, fixed division of an RF source before frequency conversion or synthesis. Its 18 GHz maximum input and divide-by-8 ratio allow a high-frequency source to be translated into a lower-frequency signal while retaining a fixed relationship to the original source. Because the device has differential 100 Ω outputs, the instrument’s signal path should use controlled impedance and minimize discontinuities. Validate gain budget, return loss, harmonic content, and phase-noise degradation to ensure the divider does not limit instrument accuracy.
Được đề xuất
Microwave Communication Signal Conditioning
The ADF5002BCPZ-RL7 can condition a microwave-frequency signal in communications equipment by reducing it by 8 before further processing. Its maximum input frequency of 18 GHz covers high-band RF test and conversion contexts, while the 3.3 V operation supports integration with compact low-voltage electronics. The differential output must transition into a balanced receiver or PLL input with controlled impedance and adequate isolation. Board-level RF layout, connector launches, grounding, and return paths should be designed so reflections and coupling do not degrade the 100 Ω differential interface.
Được đề xuất
Low-Phase-Noise Frequency Generation
The ADF5002BCPZ-RL7 is positioned as a low-noise, low-power RF divider for use ahead of PLL synthesis. Dividing a stable reference signal by 8 can reduce the frequency presented to the PLL while preserving a deterministic relationship to the original source. The divider’s contribution to phase noise and spurs is important in this application, so the complete signal chain must be assessed with the downstream loop bandwidth and reference specifications. The 3.3 V supply and differential 100 Ω outputs favor compact, controlled-impedance implementations when the PCB reference plane is kept continuous.
Được đề xuất
Instrumentation and Calibration Loops
The ADF5002BCPZ-RL7 can provide fixed division within instrumentation and calibration circuits that need a lower-frequency representation of a microwave source. The divide-by-8 ratio makes output-frequency calculation direct, and the 18 GHz input capability supports RF instrumentation operating near the device’s upper limit. A practical implementation should keep the RF path short, provide a continuous ground reference, and isolate the divider from switching circuitry. The PLL or measurement receiver should also be checked for allowable input power, bandwidth, and input-referred noise so that the divider’s characteristics remain compatible with the calibration uncertainty.
Được đề xuất
RF Frequency Divider Subsystem
The ADF5002BCPZ-RL7 can serve as the dedicated RF divider stage in a larger synthesizer subsystem that requires division of carrier-frequency signals before low-bandwidth processing. Its fixed divide-by-8 function avoids the control complexity of a programmable divider and supports a straightforward implementation around a 3.3 V rail. The subsystem should include local supply bypassing, a stable reference and ground arrangement, and controlled-impedance RF routing to the receiving PLL. Validate startup, unwanted coupling, output level, return loss, and temperature-dependent behavior across the intended −40°C to +105°C operating range.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADF5002BCPZ-RL7 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Brand | Analog Devices |
| Package | 16-lead WFQFN CSP with exposed pad |
| Product Type | Fixed RF prescaler |
| Maximum Input Frequency | 18 GHz |
| Divide Ratio | 8:1 |
| Supply Voltage | 3.3 V ±10% |
| Output Configuration | Differential |
| Output Impedance | 100 Ω differential |
| Operating Temperature Range | −40°C to +105°C |
Bảo phân biệt quan trọng
- Fixed microwave division in a compact exposed-pad package (vsGeneric programmable RF divider)
- Direct interface to compatible PLL prescaler inputs (vsSingle-ended RF divider)
- Low-voltage operation for compact RF systems (vsHigher-supply prescaler)
Ghi chú thiết kế
Treat the RF input and differential outputs as controlled-impedance transmission lines rather than ordinary low-frequency nets. Keep the input path and output routes short, minimize stubs and via transitions, and maintain a continuous reference plane beneath the RF traces. Provide interface structures that match the device’s single-ended input and 100 Ω differential output environment. Validate the final stack-up and geometry with electromagnetic or measurement data where the operating band makes connector and via parasitics significant.
Use the exact land pattern and exposed-pad connection method in the official ADF5002 datasheet. The exposed pad is integral to the 16-lead WFQFN CSP construction and must be incorporated into copper, solder, and assembly planning. Keep thermal-via placement consistent with the manufacturer land pattern while avoiding RF return-path discontinuities. Validate pad dimensions, solder-mask policy, paste volume, and reflow profile against the current package drawing before releasing the PCB.
The device operates from a 3.3 V supply, and the manufacturer’s test conditions specify a tolerance of ±10%. Place the required local decoupling capacitors at the supply and ground pins, with short, low-inductance connections and a solid ground reference. Check the downstream PLL’s supply requirements because the divider and PLL may need coordinated sequencing or filtering. Confirm actual supply noise at the pins rather than relying only on the nominal 3.3 V rail value.
Confirm the interface to the receiving PLL for allowable input power, impedance, bandwidth, isolation, and input-referred noise. Although the divider ratio and maximum input frequency may appear compatible, an unmatched output or excess signal level can degrade phase noise or overload the PLL input. Consider the output drive and downstream network together, and use the manufacturer’s application information as the starting point for component values and topology.
Do not interpret the ADF5002BCPZ and ADF5002BCPZ-RL7 records as proof of interchangeable procurement options without checking the ordering code, packing form, termination treatment, and reel details. Also avoid substituting a generic divider merely because it reaches a similar frequency. A true drop-in choice must match the package dimensions, pin assignments, exposed pad, supply, divide ratio, RF impedance, and operating limits.
Thông tin tuân thủ
The exact-MPN product record states RoHS compliance. No qualifying information establishes REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status.