ADM213EARZ - 4/5 5V RS-232 Transceiver | Analog Devices
MPN: ADM213EARZ ✓ Hoạt độngADM213EARZ Tóm tắt
An RS-232 transceiver is an interface IC that combines line drivers and line receivers on one chip. EIA-232 and V.28 signaling converts between low-voltage logic levels and the bipolar voltage levels used by RS-232 equipment. In the signal-chain hierarchy, this device belongs to the RS-232 interface IC family, performs logic-level conversion, and serves as the physical communication layer between digital equipment and a serial port.
The ADM213E family includes four RS-232 drivers and five receivers, with two receivers remaining active during shutdown. Its enhanced electrical protection includes ±15 kV ESD protection, while the single 5 V operating supply simplifies system implementation. The ADM213E product family is also identified as compliant with applicable EIA-232E, CCITT V.28, and EU EMC requirements.
The ADM213EARZ combines four transmit channels with five receive channels for multi-port RS-232 equipment. Its 230 kbps maximum data rate supports legacy serial communications, industrial control links, data-acquisition systems, and service interfaces. Shutdown capability can reduce power use when communication is inactive, while selected receiver channels remain operational for monitoring or wake functions.
Typical uses include industrial serial-port expansion, instrumentation control, data-logger interfaces, board-to-board communication links, and equipment requiring multiple RS-232 channels. The 28-pin SOIC package allows a compact implementation, although careful treatment of driver outputs, receiver inputs, supply bypassing, and external protection is required in electrically harsh installations.
Place the supply bypass capacitor close to the device and route each RS-232 driver output away from sensitive receiver and logic traces. Confirm that every connected cable meets the EIA-232E and V.28 limits, and use suitable protection when cables leave the equipment enclosure. Review shutdown-state receiver behavior before assigning pins in a multi-drop or monitoring system.
This product record combines the manufacturer’s ADM213E technical description with application-oriented implementation guidance, practical interface considerations, and a structured comparison against pin-compatible RS-232 transceiver options. The Request a Quote form on this page supports purchasing, availability, and lead-time inquiries for the ADM213EARZ.
Bộ thay thế dễ dàng lắp đặt cho ADM213EARZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADM213EARZ (cùng hình factor và footprint) — khác nhau ở Product Type, Supply Voltage, Enable Control, Maximum Data Rate, Package.
ADM213EAR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADM213EARSZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
HIN213EIBZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX213CDW
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX213CDWR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADM213EARZ Thông số kỹ thuật
| Product Type | RS-232/V.28 line transceiver |
| Điện áp cung cấp | 4.5 V to 5.5 V |
| Nominal Supply Voltage | +5 V |
| Maximum Data Rate | 230 kbps |
| Driver Count | 4 |
| Receiver Count | 5 |
| Receivers Active During Shutdown | 2 |
| ESD Protection | ±15 kV |
| Interface Standard | EIA-232E and CCITT V.28 |
| Shutdown Control | Available |
| Enable Control | Available on selected family products |
| Hộp | 28-pin SOIC |
| Package Width | 7.50 mm |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân ADM213EARZ 7.50 mm
Cấu hình chân cho ADM213EARZ (7.50 mm gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ADM213EARZ.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ADM213EARZ phù hợp cho 6 Áp dụngs: Industrial Serial Port Expansion, Data Acquisition Instrumentation, Industrial Control Equipment, Data Logger Communications, Board-to-Board Communication, Network Equipment Service Ports.
Industrial Serial Port Expansion
The ADM213EARZ is suitable for industrial controllers that need more RS-232 ports than their main processor can provide directly. Four driver channels can support outbound command paths, while five receiver channels can accept acknowledgments, interlocks, and equipment-status signals. Its 4.5 V to 5.5 V single-supply operation simplifies integration with 5 V control electronics, and the 230 kbps rate accommodates conventional asynchronous industrial links. The 28-pin SOIC footprint also preserves space on densely populated control boards. Designers should verify shutdown polarity and the behavior of the two receivers that remain active before assigning monitoring functions.
Được đề xuất
Data Acquisition Instrumentation
The ADM213EARZ fits laboratory and process-instrumentation systems that exchange commands and measurements through legacy RS-232 equipment. Its four transmitters can connect separate instruments or control targets, while five receivers provide additional channels for status, alarms, and remote signaling. The 230 kbps maximum data rate is more than adequate for legacy measurement protocols, and the single 5 V supply reduces the need for bipolar interface rails. For bench systems, keep long cable outputs away from sensitive analog circuitry and follow the Analog Devices application guidance for supply bypassing and external protection.
Được đề xuất
Industrial Control Equipment
The ADM213EARZ can provide the multi-channel serial boundary between a controller and external actuators, programmers, or service equipment. Four driver outputs support command transmission, and five receiver inputs allow controller monitoring of completion signals and fault conditions. Operation from 4.5 V to 5.5 V aligns with common 5 V industrial logic, while ±15 kV ESD protection strengthens the interface against electrostatic discharge encountered during installation and servicing. Engineers should validate the complete EIA-232E and V.28 interface, especially grounding and cable protection, before deploying the device in an electrically noisy enclosure.
Được đề xuất
Data Logger Communications
The ADM213EARZ is appropriate for data loggers that communicate with computers, sensors, or local service terminals over RS-232. Multiple driver and receiver channels allow simultaneous command output and status collection without using several separate transceiver packages. The device’s 230 kbps capability supports legacy serial logging protocols, and its single 5 V supply simplifies power architecture in compact logging equipment. Shutdown control can be useful during idle periods, while the two receivers that remain active can preserve selected monitoring or wake indications. Firmware developers should test all control states and cable transitions before deploying the interface in unattended installations.
Được đề xuất
Board-to-Board Communication
The ADM213EARZ can bridge two circuit boards that use a legacy RS-232 physical interface rather than a modern differential standard. Its four transmitters and five receivers support several point-to-point links within an enclosure, provided the standard RS-232 electrical and grounding requirements are satisfied. The 230 kbps data rate supports low- and moderate-speed command traffic, while ±15 kV ESD protection improves resilience in industrial or service-accessible systems. For internal board links, minimize trace lengths between transceivers, provide local supply decoupling, and verify that the system’s ground reference meets EIA-232E requirements.
Được đề xuất
Network Equipment Service Ports
The ADM213EARZ is useful in network and communications equipment that retains an RS-232 service, console, or equipment-maintenance port. Four driver channels can support console and auxiliary control links, while five receivers can receive status from connected field equipment. The single 5 V supply integrates cleanly with conventional communications hardware, and the 230 kbps rate exceeds the needs of most administrative and service protocols. Because service ports are often exposed during installation, keep ESD protection and external cable protection in the design, route driver traces away from clocked circuitry, and verify shutdown behavior for remote-management workflows.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADM213EARZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADM213EAR | ADM213EARSZ | HIN213EIBZ | MAX213CDW | MAX213CDWR |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Renesas Electronics | Maxim Integrated | Maxim Integrated |
| Package | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC |
Bảo phân biệt quan trọng
- Five receivers extend beyond the four available drivers (vsMAX213CDW)
- Higher documented family data rate (vsHIN213EIBZ)
- Defined ESD protection for interface robustness (vsMAX213CDWR)
- Two receivers remain active in shutdown (vsADM213EAR)
Ghi chú thiết kế
Place the supply bypass capacitor immediately beside the ADM213EARZ power and ground pins, and provide a short return path to the device. Keep RS-232 driver outputs physically separated from receiver inputs and low-level logic traces to reduce coupling. Match connector-side protection components close to the connector so surge or ESD current is diverted before reaching the transceiver pins.
Do not assign a shutdown-state function without checking the ADM213E control logic. Two receivers remain active during shutdown, but the usable channels, active-level polarity, and behavior of the drivers must be verified against the manufacturer pin and timing tables. A pinout copied from a different RS-232 transceiver can produce an apparently functional board with reversed control polarity or incompatible receiver activity.
RS-232 is a single-ended interface whose cable currents can couple into surrounding circuitry. Route driver and receiver nets away from clocks, precision analog signals, and switching-regator power loops. Maintain the required ground relationship between communicating equipment, and consider external protection for user-accessible cables where installation transients or ESD events are likely.
The ADM213EARZ supports operation up to 230 kbps, so conventional board-level interconnects are generally adequate. Nevertheless, use short driver traces, avoid unnecessary stubs, and observe the EIA-232E and CCITT V.28 system requirements. When substituting another transceiver, compare control-pin polarity and shutdown behavior in addition to package, voltage, speed, and channel count.
Thông tin tuân thủ
Analog Devices identifies the ADM213E family as compliant with applicable EU EMC requirements. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statuses are not stated in the cited product information.