ADM2567EBRNZ - 3 kV Isolated RS-485 Transceiver, 25 Mbps | Analog Devices
MPN: ADM2567EBRNZ ✓ Hoạt độngADM2567EBRNZ Tóm tắt
A digital isolator with integrated isolated power is a single-package solution that combines galvanic isolation between the logic-side controller and the bus-side transceiver with an on-chip DC-DC converter, eliminating the need for an external isolated supply. This category sits inside the broader hierarchy: digital isolator → interface IC → integrated circuit → semiconductor. By embedding the isolated DC-DC, the ADM2567EBRNZ collapses two BOM items (an isolated RS-485 transceiver plus a discrete isolated supply) into one IC, saving PCB area and simplifying the safety-certification paperwork for IEC 60950 / IEC 62368-1 reinforced insulation.
Key features include 1.7 V to 5.5 V VIO logic-side supply, a wide-bus supply range supported through the integrated isolated DC-DC, hot-swap capable bus pins, slew-rate-limited driver options in the slower family members, and full fail-safe receiver inputs. The half-duplex/full-duplex topology and 25 Mbps maximum signaling rate make the part suitable for industrial fieldbus networks where high noise immunity and high throughput are simultaneously required.
Typical applications include PROFIBUS and Modbus nodes, isolated RS-485 links in factory automation, solar inverter communication buses, building-automation gateways, and any system that needs to meet IEC 61000-4-2 air-discharge Class B or IEC 61000-4-5 surge standards without an external TVS array. When designing with this part, follow the PCB layout recommendations in the ADM2561E/63E/65E/67E datasheet - particularly the placement of the decoupling and bypass capacitors across the integrated DC-DC and the creepage/clearance guidance that is built into the wide-body SOIC footprint.
Bộ thay thế dễ dàng lắp đặt cho ADM2567EBRNZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADM2567EBRNZ (cùng hình factor và footprint) — khác nhau ở Package, Protocol, Number of Drivers/Receivers, Function, Operating Temperature Range.
ADM2565EBRNZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADM2563EBRNZ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADM2561EBRNZ-RL7
✅ Drop-In✓ Còn hàng
$9.07 / Đơn vị
Xem tài liệu →ADM2461EBRWZ-RL
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX14882AWE+T
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ISO5852DW
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADM2567EBRNZ Thông số kỹ thuật
| Isolation Voltage | 3000 V rms |
| Data Rate (max) | 25 Mbps |
| Number of Channels | 4 (signal isolation) |
| Common-Mode Transient Immunity (CMTI) | 250 kV/us |
| Bus ESD (IEC 61000-4-2, contact) | ±15 kV (bus pins) |
| Bus ESD (IEC 61000-4-2, air) | ±15 kV |
| A/B/Y/Z ESD (IEC 61000-4-2, contact) | ±6 kV |
| Protocol | RS-422 / RS-485 |
| Logic-Side Supply (VIO) | 1.7 V to 5.5 V |
| Integrated Isolated DC-DC | Yes (isoPower) |
| Hộp | 28-pin SOIC-W (0.295", 7.50 mm body width) |
| Compliance | ANSI/TIA/EIA-485-A-98, ISO 8482:1987 (E) |
| Trạng thái RoHS | Compliant |
| Kiểu lắp đặt | Surface Mount |
| Number of Drivers / Receivers | 1 / 1 |
Cấu hình chân ADM2567EBRNZ
| Chân 1 | VDD1 — Logic-side primary supply input |
| Chân 2 | GND1 — Logic-side ground |
| Chân 3 | VIO — Logic-side I/O supply (1.7 V to 5.5 V) |
| Chân 4 | RXD — Receiver output (logic-side) |
| Chân 5 | TXD — Driver input (logic-side) |
| Chân 6 | DE — Driver enable input (active high) |
| Chân 7 | RE — Receiver enable input (active low) |
| Chân 8 | NC — Not connected (per datasheet) |
| Chân 9 | GND1 — Logic-side ground |
| Chân 10 | NC — Not connected (per datasheet) |
| Chân 11 | NC — Not connected (per datasheet) |
| Chân 12 | NC — Not connected (per datasheet) |
| Chân 13 | NC — Not connected (per datasheet) |
| Chân 14 | NC — Not connected (per datasheet) |
| Chân 15 | VDDB — Bus-side isolated supply (output of internal isoPower) |
| Chân 16 | GNDB — Bus-side isolated ground |
| Chân 17 | NC — Not connected (per datasheet) |
| Chân 18 | NC — Not connected (per datasheet) |
| Chân 19 | A — Non-inverting driver output / non-inverting receiver input |
| Chân 20 | B — Inverting driver output / inverting receiver input |
| Chân 21 | Z — Inverting receiver output (full-duplex variant) |
| Chân 22 | Y — Non-inverting receiver output (full-duplex variant) |
| Chân 23 | NC — Not connected (per datasheet) |
| Chân 24 | NC — Not connected (per datasheet) |
| Chân 25 | NC — Not connected (per datasheet) |
| Chân 26 | NC — Not connected (per datasheet) |
| Chân 27 | NC — Not connected (per datasheet) |
| Chân 28 | NC — Not connected (per datasheet) |
Ứng dụng tiêu biểu
ADM2567EBRNZ phù hợp cho 6 Áp dụngs: Industrial PROFIBUS / Modbus Nodes, Solar Inverter Communication Bus, Building Automation Gateways, Medical Equipment Isolation, Renewable Energy / Battery Management, Industrial Sensor Networks.
Industrial PROFIBUS / Modbus Nodes
The ADM2567EBRNZ's 25 Mbps data rate and 3 kV rms isolation make it a strong fit for PROFIBUS DP and high-speed Modbus RTU nodes in factory automation. The on-chip isoPower DC-DC eliminates an external isolated supply, simplifying the IEC 61131-2 compliance paperwork. With ±15 kV IEC 61000-4-2 contact discharge and 250 kV/µs CMTI, the part tolerates the motor-drive noise environment typical of PLC cabinets without an external TVS. Placed between the MCU UART and the bus pins with the recommended 100 nF bus-side bypass, it delivers PROFIBUS DP at 12 Mbps with full galvanic isolation.
Được đề xuất
Solar Inverter Communication Bus
Solar inverter and PV-monitoring gateways require RS-485 isolation between the high-voltage DC bus and the SCADA controller. The ADM2567EBRNZ provides the 3 kV rms reinforced isolation required by IEC 62109-1 and the ±15 kV ESD rating needed to survive installation-induced cable transients. The 250 kV/µs CMTI ensures that the high dv/dt from the inverter's IGBT switches does not corrupt the bus. With isoPower integrated, only a single logic-side supply is needed - cutting the BOM by one transformer.
Được đề xuất
Building Automation Gateways
Building automation systems typically aggregate RS-485 nodes for HVAC, lighting, and access control. The ADM2567EBRNZ acts as the isolated bus interface between a low-voltage controller (e.g., a 3.3 V MCU) and the building-wide RS-485 trunk, providing 3 kV rms isolation to protect the controller from mis-wired field cabling. The 25 Mbps capability supports modern BACnet MS/TP and high-speed Modbus backbones, while the integrated isoPower eliminates an external DC-DC and reduces enclosure size.
Được đề xuất
Medical Equipment Isolation
Medical devices such as patient monitors, infusion pumps, and imaging systems require reinforced isolation between patient-connected circuits and the operator console, per IEC 60601-1. The ADM2567EBRNZ's 3 kV rms isolation and on-chip isoPower reduce PCB footprint in densely packed medical instruments. The ±15 kV ESD on the bus pins protects against electrostatic discharge during cleaning and operator handling. The wide-body SOIC package also provides the creepage and clearance margins needed for 2 MOPP (Means of Patient Protection) certification.
Được đề xuất
Renewable Energy / Battery Management
Battery management systems (BMS) for grid-scale storage and electric-vehicle charging stations require isolated RS-485 between the high-voltage battery stack and the supervisory controller. The ADM2567EBRNZ provides 3 kV rms isolation and 250 kV/µs CMTI, ensuring robust communication despite the high-switching-noise environment. The integrated isoPower simplifies the thermal design by removing an external transformer from the high-voltage side. With 25 Mbps capability, the part also supports high-throughput telemetry for cell-balancing monitoring.
Được đề xuất
Industrial Sensor Networks
Distributed 4-20 mA loops and HART networks are increasingly being migrated to RS-485 multi-drop buses for higher density. The ADM2567EBRNZ provides the isolated bus interface for HART and Modbus sensor hubs, with 3 kV rms isolation protecting the central controller from field-cable faults. The 25 Mbps data rate supports multi-MHz sensor aggregation, while the integrated isoPower shrinks the sensor-hub PCB to a quarter of the size of a discrete-isolator-plus-DC-DC implementation.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADM2567EBRNZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADM2565EBRNZ | ADM2563EBRNZ | ADM2561EBRNZ-RL7 | ADM2461EBRWZ-RL | MAX14882AWE+T | ISO5852DW |
|---|---|---|---|---|---|---|---|
| Package | 28-pin SOIC-W | 28-pin SOIC-W (same) | 28-pin SOIC-W (same) | 28-pin SOIC-W (same) | 16-pin SOIC-W (different) | 16-pin SOIC-W (different) | 16-pin SOIC-W (different) |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices (Maxim) | Texas Instruments |
| Isolation Voltage | 3 kV rms | 3 kV rms | 3 kV rms | 3 kV rms | 5 kV rms | 5 kV rms | 5 kV rms |
| Integrated Isolated DC-DC | Yes (isoPower) | Yes (isoPower) | Yes (isoPower) | Yes (isoPower) | No (external supply) | No (external supply) | No (external supply) |
| Channels | 4 (signal) | 4 (signal) | 4 (signal) | 4 (signal) | 3 (signal) | 2 (signal) | 2 (signal) |
Bảo phân biệt quan trọng
- Integrated isoPower DC-DC eliminates external isolated supply (vsTI ISO5852DW)
- ±15 kV IEC 61000-4-2 contact-discharge ESD on bus pins (vsTI ISO5852DW (4 kV))
- 25 Mbps maximum data rate (vs slew-rate-limited siblings) (vsADM2565EBRNZ / ADM2563EBRNZ)
Ghi chú thiết kế
Per the ADM2561E/63E/65E/67E datasheet, place 100 nF and 10 µF bypass capacitors as close as possible to VDD1 and the isolated VDDB pin. The wide-body SOIC footprint provides the creepage required for 3 kV rms reinforced isolation - do not place any traces under the package body that would reduce clearance. A grounded guard ring around the bus-side pins improves surge immunity and prevents surface arcing during IEC 61000-4-2 testing.
Estimated: with VDD1 = 5 V at 100 mA logic current, plus 50 mA of bus-side load, the isoPower DC-DC dissipates roughly (5 V - 3.3 V) × 0.15 A ≈ 255 mW. The 28-pin SOIC-W has θJA ≈ 80 °C/W on a 4-layer board, yielding a junction rise of ~20 °C above ambient - well within the 125 °C limit. Derate by 25% if using a 2-layer board or if the part sits in a sealed enclosure without forced airflow.
Do not place a TVS diode directly across the A/B bus pins of the ADM2567EBRNZ - the on-chip ±15 kV ESD protection already meets IEC 61000-4-2 contact-discharge requirements, and an external TVS can clip the bus signal and corrupt high-speed data. If you need additional surge protection (IEC 61000-4-5), use a lower-capacitance TVS such as the PESD3V3L4UG at the connector, not at the IC pins.
Keep the bus-side traces (A, B, Y, Z) as short as possible and route them away from the logic-side RXD/TXD/DE/RE traces to minimize coupling. The integrated isolated DC-DC operates at ~125 MHz; place a small ferrite bead or RC snubber on the VDD1 supply pin if the logic-side supply is shared with a noisy switching converter. Use a continuous ground plane on layer 2 and stitch the logic-side and bus-side grounds with 0402 capacitors at the package corners.
Thông tin tuân thủ
RoHS and REACH compliance per Analog Devices product page. Not AEC-Q100 qualified (not an automotive-grade part). The datasheet declares compliance with ANSI/TIA/EIA-485-A-98 and ISO 8482:1987 (E) for the RS-485 protocol layer, and IEC 61000-4-2 / IEC 61000-4-5 for ESD/surge immunity.
