Analog Devices

ADM3222ARWZ - 230kbps 3.3V RS-232 Transceiver | Analog Devices

MPN: ADM3222ARWZ ✓ Hoạt động
3.3 V Vdss 18-SOIC, 7.50 mm wide Package
MOQ: 1 |

ADM3222ARWZ Tóm tắt

The Analog Devices ADM3222ARWZ is a two-driver, two-receiver RS-232 transceiver designed for 3.3 V single-supply operation, with data rates up to 230 kbps in an 18-lead SOIC package. Its integrated charge-pump circuitry supports EIA-232E and CCITT V.28 interfaces while reducing the external component count.

An RS-232 transceiver is a semiconductor interface that converts logic-level signals into RS-232 line levels and receives RS-232 signals back into logic-compatible levels. It belongs to the interface IC hierarchy, connecting UART, UART-over-USB, and embedded systems to legacy RS-232 equipment. The ADM3222ARWZ provides bidirectional conversion through two driver channels and two receiver channels.

Principal features include operation from a single 3.3 V supply, low-power shutdown circuitry, four external 0.1 µF charge-pump capacitors, and support for portable instrumentation. The manufacturer product page specifies data rates up to 230 kbps. One distributor specification listing also identifies a 3 V to 5.5 V supply range, allowing the interface to operate across common low-voltage systems.

The charge-pump voltage doubler and inverter generate the bipolar voltage required by RS-232 from one low-voltage supply. Four external capacitors stabilize these rails, while the receiver channels translate the remote line voltage into CMOS-compatible signals. The separate transmit and receive channels permit simultaneous full-duplex operation on two ports.

Typical uses include battery-powered portable instruments, industrial data-acquisition equipment, point-of-sale terminals, service interfaces, and embedded systems that must communicate with RS-232 equipment. The 18-lead SOIC package is suitable for compact surface-mounted assemblies requiring two RS-232 ports.

PCB design must reserve the four charge-pump capacitor connections and place the capacitors close to their associated pins. A solid ground plane, short return paths, and controlled routing of exposed RS-232 cable-side nets help reduce radiated emissions and susceptibility to external interference.

This page combines interface specifications, application guidance, pin-compatible family options, and design notes to support component selection, schematic review, PCB implementation, and sourcing decisions for the ADM3222ARWZ.

Bộ thay thế dễ dàng lắp đặt cho ADM3222ARWZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

ADM3222ARW

✅ Drop-In
📦 18-SOIC (0.295, 7.50 mm width)
Same ADM3222 family and 18-SOIC footprint; ordering suffix indicates a different temperature-grade option, requiring qualification against the target operating range.

📋 Tham chiếu thay thế (không có trong danh mục)

ADM3202ARWZ

✅ Drop-In
Analog Devices
📦 18-SOIC (0.295, 7.50 mm width)
Dual RS-232 line driver and receiver · 2 channels · 2 channels · +3.3 V · Up to 230 kbps · EIA-232E and CCITT V.28 · 4 external 0.1 µF capacitors · Full duplex

Liên hệ để biết giá

Xem tài liệu →

ADM3222ARWZ Thông số kỹ thuật

Number of Drivers 2
Number of Receivers 2
Transceiver Configuration 2/2 full-duplex RS-232
Nominal Supply Voltage 3.3 V
Supply Voltage Range 3 V to 5.5 V
Maximum Data Rate 230 kbps
Listed Feature Data Rate 460 kbps
Interface Standard EIA-232E
Interface Standard CCITT V.28
External Charge-Pump Capacitors 4 x 0.1 µF
Power Supply Architecture Single +3.3 V supply
Shutdown Function Yes
Hộp 18-SOIC, 7.50 mm wide
Kiểu lắp đặt Surface mount
Lead-Free Status Lead-free

Hướng dẫn cấu hình chân ADM3222ARWZ 18-soic, 7.50 mm wide

Cấu hình chân cho ADM3222ARWZ (18-soic, 7.50 mm wide gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.

Bảng cấu hình chân 18-soic, 7.50 mm wide cho ADM3222ARWZ

Không có dữ liệu chân cụ thể sẵn có cho ADM3222ARWZ.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

ADM3222ARWZ phù hợp cho 6 Áp dụngs: Portable Instrument Serial Interface, Industrial Data Acquisition, Point-of-Sale Terminal, Embedded UART-to-RS-232 Bridge, Network Equipment Maintenance Port, Medical and Laboratory Instrument Control.

📱

Portable Instrument Serial Interface

The ADM3222ARWZ fits portable test and measurement instruments that expose a legacy RS-232 service port while operating from a 3.3 V battery-powered rail. Two drivers and two receivers provide full-duplex communication on two channels, while the single-supply charge-pump architecture removes the need for a separate negative voltage rail. Its manufacturer-listed data rate of up to 230 kbps supports service-console and instrument-control traffic. Low-power shutdown is particularly useful during inactive periods, although the system-level sleep budget must include UART activity and charge-pump capacitor behavior.

🏭

Industrial Data Acquisition

The ADM3222ARWZ can connect a 3.3 V controller to two full-duplex RS-232 channels in industrial data-acquisition equipment. The dual 2/2 channel arrangement allows command traffic and measurement data to be handled simultaneously, reducing the need for separate RS-232 interface devices. Operation from one low-voltage supply simplifies system power distribution, and the charge-pump capacitors can be placed close to the device pins for cleaner routing. Engineers should allow adequate RS-232 line protection and verify cable length, grounding, and baud-rate requirements in the target installation.

🔧

Point-of-Sale Terminal

Point-of-sale terminals and service consoles can use the ADM3222ARWZ to bridge modern 3.3 V logic and RS-232 peripherals. Two transmitters and two receivers support more than one legacy device, including a printer, scanner, or service interface. The single 3.3 V supply architecture is useful where negative rail generation would add board area, while the listed rate of up to 230 kbps is more than sufficient for common peripheral traffic. Shutdown control can reduce demand when the terminal is idle, but system firmware should assert the relevant control states only after reviewing the datasheet timing.

🖥️

Embedded UART-to-RS-232 Bridge

The ADM3222ARWZ is suitable for an embedded UART-to-RS-232 bridge because it accepts logic-level signals and supplies the bipolar line levels required by RS-232 equipment. A single 3.3 V supply reduces the power-tree complexity of the bridge, while four external 0.1 µF capacitors support the integrated charge-pump function. The two-channel arrangement can serve two external ports with independent transmit and receive paths. Firmware must keep the UART baud rate within the interface capability, and PCB routing should keep high-voltage line-side nets away from sensitive logic and ground-return paths.

🌐

Network Equipment Maintenance Port

The ADM3222ARWZ can implement a maintenance or diagnostic RS-232 port on network equipment that otherwise uses 3.3 V electronics. Its small 18-SOIC footprint and dual-channel capability make it suitable for providing both a primary console and an auxiliary service connection. The manufacturer lists conformance to EIA-232E and CCITT V.28, supporting interoperability with conventional RS-232 equipment. Because maintenance connectors can be accessible from outside an enclosure, add the appropriate transient-voltage and surge protection required by the installation while keeping protection current away from the transceiver inputs.

💊

Medical and Laboratory Instrument Control

The ADM3222ARWZ can support RS-232 control or service connections in laboratory and medical instruments that use 3.3 V embedded controllers. The dual-driver, dual-receiver arrangement enables full-duplex command links and reduces external interface-component count, while shutdown support can help conserve power between test cycles. The listed 230 kbps capability is appropriate for control traffic rather than high-volume bulk transfer. Confirm medical-system safety requirements separately, preserve appropriate isolation boundaries, and review the complete pin and timing information in the manufacturer datasheet before using this device in a safety-related pathway.

Tóm tắt các sản phẩm được đề xuất

ADM3202ARWZ Analog Devices Được sử dụng trong: Portable Instrument Serial Interface, Industrial Data Acquisition, Point-of-Sale Terminal, Embedded UART-to-RS-232 Bridge, Network Equipment Maintenance Port, Medical and Laboratory Instrument Control ADM1385ARUZ Related low-power RS-232 interface family member Được sử dụng trong: Portable Instrument Serial Interface, Industrial Data Acquisition, Point-of-Sale Terminal, Embedded UART-to-RS-232 Bridge, Network Equipment Maintenance Port, Medical and Laboratory Instrument Control
What is the ADM3222ARWZ?
The ADM3222ARWZ is a two-driver, two-receiver RS-232 transceiver for single-supply operation at 3.3 V. According to the Analog Devices ADM3222 product page, it supports data rates up to 230 kbps, conforms to EIA-232E and CCITT V.28, and uses four external 0.1 µF charge-pump capacitors. It is packaged in an 18-lead SOIC for surface-mounted industrial, portable-instrument, and embedded communication equipment.
What is the operating voltage of ADM3222ARWZ?
The ADM3222ARWZ operates from a nominal 3.3 V supply, with a published supply range of 3 V to 5.5 V. The Analog Devices ADM3222 family is designed to generate the bipolar RS-232 signal levels required by EIA-232E from one low-voltage supply. This makes the device suitable for 3.3 V UART systems, portable instruments, and embedded controllers that cannot accommodate a separate negative power rail.
How fast is the ADM3222ARWZ RS-232 interface?
The Analog Devices ADM3222 product page specifies operation at data rates up to 230 kbps. One distributor specification listing also identifies a 460 kbps feature for the device family. Because the two published rates refer to different feature classifications or test conditions, use 230 kbps as the manufacturer-product-page operating figure and confirm the required channel, slew-rate, and loading conditions against the datasheet before selecting a cable or baud rate.
Where can I download the ADM3222ARWZ datasheet PDF?
The official ADM3222 datasheet and product information are available from Analog Devices at https://www.analog.com/en/products/adm3222.html. The manufacturer page documents the 3.3 V supply architecture, up to 230 kbps operation, EIA-232E and CCITT V.28 conformance, shutdown support, and the four external 0.1 µF charge-pump capacitors. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks.
Where can I find the ADM3222ARWZ pinout?
The ADM3222ARWZ pinout is shown in the pin-description table of the Analog Devices ADM3222 manufacturer datasheet. The device is an 18-lead SOIC, and its interface includes two driver inputs, two driver outputs, two receiver inputs, two receiver outputs, supply connections, charge-pump capacitor connections, and enable or shutdown-related connections. Use that table to confirm every net before fabrication because package and function suffixes identify distinct ordering variants.
What are the key specifications of ADM3222ARWZ that engineers should know?
The ADM3222ARWZ combines two RS-232 drivers, two RS-232 receivers, a single 3.3 V supply architecture, and a maximum listed data rate of 230 kbps in an 18-lead SOIC. The Analog Devices product page also identifies EIA-232E and CCITT V.28 conformance, low-power shutdown, and four external 0.1 µF charge-pump capacitors. Its primary engineering benefit is full-duplex dual-port RS-232 connectivity without a separate negative supply rail.
Can ADM3222ARWZ be used with a 3.3 V UART?
Yes, the ADM3222ARWZ is designed to interface a 3.3 V UART with an RS-232 port. The driver channels accept logic-level transmit signals and generate RS-232 line levels, while the receiver channels convert incoming line voltages into logic-compatible signals. The single 3.3 V supply and integrated charge-pump architecture eliminate the need for a separate negative voltage rail, while UART baud rate must remain compatible with the interface rating of up to 230 kbps.
What is the difference between ADM3222ARWZ and ADM3222ARW?
The ADM3222ARWZ and ADM3222ARW are closely related 18-SOIC members of the same Analog Devices family, but their ordering suffixes identify different temperature or qualification variants. The ARWZ form is the specified target MPN, while ADM3222ARW is the lower-temperature-family option identified in cross-reference results. Verify the temperature rating and production grade in the manufacturer ordering information before treating the alternate suffix as a drop-in replacement.
What is the difference between ADM3222ARWZ and ADM3202ARWZ?
The ADM3222ARWZ includes the enable and shutdown circuitry associated with the ADM3222 family, while the ADM3202 is a related lower-power RS-232 transceiver without the same shutdown feature. Cross-reference sources directly compare the two devices, and both families use 3.3 V operation and charge-pump-based RS-232 level generation. Confirm shutdown-state pin behavior and the complete 18-lead pin map before replacing an existing design.
When should I choose ADM3222ARWZ over ADM3202ARWZ?
Choose the ADM3222ARWZ when the design benefits from controllable low-power shutdown in a portable or battery-operated instrument. The Analog Devices family page identifies shutdown circuitry specifically for the ADM3222 and ADM1385, whereas ADM3202 is the basic low-power member. For a fixed, continuously powered industrial interface, the ADM3202 may be sufficient, but validate its pin configuration and shutdown requirements before selecting it over the ADM3222ARWZ.
Is ADM3222ARWZ suitable for battery-powered portable instruments?
The ADM3222ARWZ is suitable for battery-powered portable instruments because it operates from one 3.3 V supply and includes low-power shutdown functionality. The Analog Devices product page identifies the ADM3222 and ADM1385 as especially appropriate for portable instrumentation where reduced power consumption is important. Its shutdown control can help lower system demand during inactive periods, although the complete battery-life calculation must include the UART and external charge-pump capacitor leakage.
What is the best drop-in replacement for ADM3222ARWZ?
The closest identified drop-in option is the Analog Devices ADM3222ARW in the same 18-SOIC format. It belongs to the same ADM3222 interface family, but the ordering suffix may change the temperature grade, so verify that its electrical limits and qualification status meet the target application's requirements. The ADM3202ARWZ is another same-package family alternative, but it does not provide the ADM3222 family's shutdown feature. No verified cross-brand, pin-compatible replacement was established.
Can ADM3202ARWZ replace ADM3222ARWZ?
ADM3202ARWZ can serve as a close family-level substitute only after checking shutdown and enable behavior. Unlike the ADM3222ARWZ, the ADM3202 family does not include the ADM3222's shutdown circuitry, so an existing control net or power-management sequence may need to change. Both devices use single low-voltage supply and charge-pump techniques, but the complete 18-lead pin map should be compared before treating the substitution as a production drop-in.
What is the best Analog Devices equivalent for ADM3222ARWZ?
The best identified Analog Devices equivalent is ADM3222ARW because it is a direct 18-SOIC family option rather than a different package or function class. The principal decision factor is the ordering suffix and its associated temperature-grade implications. If shutdown capability is not used, ADM3202ARWZ is another possible family option, but it lacks the ADM3222-specific shutdown circuitry. The ADM1385 offers fewer RS-232 channels and is therefore not an equivalent functional replacement.
Where can I buy ADM3222ARWZ and what is its lead time?
Use the Request a Quote form on this page to ask for ADM3222ARWZ pricing, current stock, minimum order quantity, and lead time. The part is offered in 18-SOIC ordering variants, including the reel-associated suffix referenced by the ADM3222ARWZ reel search terms. Confirm the exact ordering code and authorized source before placing a production order so the temperature grade and packing format match the design.

Dữ liệu tham khảo kỹ thuật cho ADM3222ARWZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the ADM3222ARWZ for a 3.3 V RS-232 interface that needs two driver channels, two receiver channels, and controllable low-power shutdown. Its manufacturer-listed 230 kbps rate and single-supply charge-pump architecture suit portable instruments, industrial controllers, and service interfaces. Select ADM3222ARW when its temperature-grade suffix matches the installation and the board can reuse the same 18-SOIC footprint; verify the ordering information before treating it as a production substitute. Consider ADM3202ARWZ for a continuously powered design that does not depend on the ADM3222 shutdown function, but recheck enable-state behavior and firmware sequencing. No verified cross-brand, same-footprint replacement was identified, so a cross-brand redesign should be validated independently rather than assumed to be interchangeable.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này ADM3222ARW ADM3202ARWZ
Brand Analog Devices Analog Devices Analog Devices
Package 18-SOIC (0.295, 7.50 mm width) 18-SOIC (0.295, 7.50 mm width) 18-SOIC (0.295, 7.50 mm width)
Driver and Receiver Count 2 drivers and 2 receivers 2 drivers and 2 receivers 2 drivers and 2 receivers
Interface Full-duplex RS-232 Full-duplex RS-232 Full-duplex RS-232
Nominal Supply Voltage 3.3 V 3.3 V 3.3 V
Shutdown Function Yes Yes No; not identified for the ADM3202 family
Mounting Type Surface mount Surface mount Surface mount

Bảo phân biệt quan trọng

  • Adds controllable low-power shutdown to the basic low-power RS-232 transceiver family (vsADM3202ARWZ)
  • Maintains the same two-channel, full-duplex RS-232 architecture within an 18-SOIC footprint (vsADM3202ARWZ)
  • Uses a single low-voltage supply for RS-232 level generation (vsADM3222ARW)

Ghi chú thiết kế

Place the four required 0.1 µF charge-pump capacitors close to their associated ADM3222ARWZ pins and keep their return paths short. Follow the pin-description and typical-layout sections of the Analog Devices ADM3222 datasheet when assigning the capacitor nets. Avoid inserting long traces or test pads between each capacitor and the device, because additional loop area can increase charge-pump noise and make radiated-emissions performance less predictable.

Keep RS-232 driver-output routing away from UART logic, crystal circuitry, sensitive analog inputs, and other low-level signal paths. The receiver outputs are logic-side signals, while the driver outputs connect to the cable-facing pins, so maintain clear separation between those groups. Use a continuous ground reference, minimize loop area, and place any approved line protection close to the connector so surge current does not flow through the transceiver area.

Decouple the 3.3 V supply near the ADM3222ARVZ power pins with the capacitance recommended by the manufacturer datasheet and maintain a low-impedance connection to the ground plane. Do not substitute the RS-232 charge-pump capacitors for local supply bypassing; they serve a different circuit function. Verify startup, shutdown, and supply sequencing behavior in firmware so the device is not driven by an undefined logic level during power transitions.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Yes
Không halogen
Unknown
Khoáng vật xung đột
Unknown

A distributor specification listing identifies the ADM3222ARWZ as lead-free. RoHS, REACH, halogen-free, and conflict-minerals status were not established from the listed technical data.

Dữ liệu được xác minh vào: 2026-11-19 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

adm3222arwz reel adm3222arwz reel7 ADM3222ARWZ datasheet ADM3222ARWZ pinout ADM3222ARWZ datasheet pdf ADM3222ARWZ equivalent ADM3222ARWZ replacement ADM3222ARWZ cross reference ADM3222ARWZ vs ADM3202ARWZ ADM3222ARWZ 18-SOIC pinout ADM3222ARWZ 230kbps 3.3V Analog Devices ADM3222ARWZ ADM3222ARWZ application circuit ADM3222ARWZ price ADM3222ARWZ stock

Các bộ phận và thuật ngữ liên quan

Analog Devices ADM3222ARWZ ADM3222ARW ADM3202ARWZ ADM1385ARUZ RS-232 RS-232 transceiver line driver line receiver interface IC semiconductor EIA-232E CCITT V.28 3.3 V power supply charge-pump voltage doubler charge-pump voltage inverter UART 230 kbps 460 kbps 18-SOIC SOIC family surface-mount package low-power shutdown portable instrumentation industrial data acquisition
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ