ADS7806PB - 12-Bit 40 kSPS SAR ADC | Texas Instruments
MPN: ADS7806PB ✓ Hoạt độngADS7806PB Tóm tắt
A sampling ADC is a data-acquisition component that samples an analog voltage, converts it into a digital code, and transfers that code to a controller, processor, or display system. The ADS7806 belongs to the ADC hierarchy: analog-to-digital converter → sampling ADC → SAR ADC → data-acquisition IC. Its SAR architecture is useful when moderate resolution, predictable conversion behavior, low power, and flexible output interfaces are more important than the throughput and channel density of a high-speed flash converter.
Key features include 12-bit resolution, a 40 kSPS conversion rate, a single analog input, selectable parallel and serial data outputs, and operation from one +5 V supply. The available input ranges are ±10 V, 0 V to +5 V, and 0 V to +4 V. The product page specifies a minimum signal-to-noise-plus-distortion ratio of 72 dB with a 1 kHz input and an acquisition-plus-conversion time of no more than 25 microseconds. These characteristics suit industrial instrumentation, sensor acquisition, laboratory measurement, and embedded control systems.
The converter can use an internal or external reference, while offset and gain adjustments support external trimming with a single supply. Its parallel interface supports direct connection to common microprocessor and microcontroller buses, while the serial interface reduces the number of signal connections and can simplify board routing. The exact interface mode, polarity, timing, and conversion control should be selected from the manufacturer datasheet when integrating the device.
Typical applications include multichannel measurement systems using analog multiplexing, closed-loop industrial controls, laboratory data loggers, instrumentation amplifiers, and sensor-interface modules. In each case, the input network must keep voltages within the selected range, the reference and conversion timing must meet system accuracy requirements, and the digital interface must match the host processor. The 35 mW maximum power specification supports low-power acquisition without requiring a high-output-capability analog reference.
Design with the complete signal chain in mind. Select the input range, reference voltage, and interface mode before assigning PCB signals, then verify acquisition timing against the required sampling rate. Account for the PDIP footprint, analog trace isolation, reference bypass capacitance, and digital-interface levels in the schematic and layout. Request current availability, lifecycle status, and lead time through the Request a Quote form on this page.
This page combines the Texas Instruments device description, package and performance characteristics, sourcing guidance, and application-oriented engineering context. It also identifies the closest documented same-family replacement candidates while preserving the distinction between a true same-package substitution and a device that merely offers similar ADC functionality.
Bộ thay thế dễ dàng lắp đặt cho ADS7806PB — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADS7806PB (cùng hình factor và footprint) — khác nhau ở Package, Architecture, Resolution, Supply Voltage, Data Interface.
ADS7807UBE4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADS7806P
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →ADS7806PB Tỷ lệ tối đa & tính chất điện
| Converter Type | Successive-approximation-register ADC |
| Độ phân giải | 12 bit |
| Tỷ lệ lấy mẫu | 40 kSPS |
| Number of Inputs | 1 analog input |
| Architecture | Sampling CMOS ADC |
| Data Output | Parallel and serial |
| Điện áp cung cấp | +5 V single supply |
| Input Ranges | ±10 V, 0 V to +5 V, and 0 V to +4 V |
| Acquisition and Conversion Time | 25 µs max |
| Maximum Power Dissipation | 35 mW max |
| Power-Down Mode Current | 50 µA |
| SNAD | 72 dB min with 1 kHz input |
| Maximum Integral Nonlinearity | ±1/2 LSB |
| Maximum Differential Nonlinearity | ±1/2 LSB |
| Reference | Internal or external |
| Hộp | 28-pin PDIP |
| Packaging | Tube |
| Kiểu lắp đặt | Through-hole |
Hướng dẫn cấu hình chân ADS7806PB 28-pin pdip
Cấu hình chân cho ADS7806PB (28-pin pdip gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho ADS7806PB.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ADS7806PB phù hợp cho 6 Áp dụngs: Industrial Sensor Acquisition, Laboratory Instrumentation, Process Control Systems, Battery-Powered Data Logging, Embedded Control Systems, Audio and Communications Monitoring.
Industrial Sensor Acquisition
The ADS7806PB is suited to acquiring slowly changing sensor signals in industrial measurement systems because it combines a 12-bit SAR converter with a 40 kSPS sampling rate. Its selectable ±10 V, 0 V to +5 V, and 0 V to +4 V ranges allow conditioning of common industrial inputs through an external network. The 25-microsecond maximum acquisition-and-conversion time supports periodic readings, while parallel output can connect to a controller with sufficient bus capability. Reference quality, input settling, and analog-ground isolation remain critical to maintaining useful accuracy.
Được đề xuất
Laboratory Instrumentation
Laboratory instruments can use the ADS7806PB for digitizing measured voltages when 12-bit resolution and 40 kSPS are adequate. Its three documented input ranges support ±10 V measurement channels as well as unipolar 0–5 V and 0–4 V systems. The single +5 V architecture simplifies supply planning, and the 72 dB minimum SNAD provides a defined conversion-performance baseline for a 1 kHz input. For precision instruments, use a stable reference, calibrated input scaling, and shielded routing to preserve that performance.
Được đề xuất
Process Control Systems
The ADS7806PB fits process-control loops that monitor pressure, temperature, position, or level through slower analog channels. A 40 kSPS conversion rate provides ample margin for typical control-loop bandwidth, while the 25-microsecond acquisition-and-conversion limit defines the minimum converter timing budget. The 35 mW maximum device dissipation is useful in distributed control hardware with limited thermal capacity. Select the interface mode and update rate together, then verify propagation through the controller and actuator path.
Được đề xuất
Battery-Powered Data Logging
Battery-powered data loggers can benefit from the ADS7806PB because it operates from one +5 V supply, dissipates no more than 35 mW during operation, and draws only 50 microamperes in power-down mode. Its 40 kSPS capability is more than adequate for many temperature, pressure, and environmental sensors sampled at low rates. Duty-cycling the converter can reduce average consumption, although regulator quiescent current, input leakage, and external-sensor power must also be included in the energy budget.
Được đề xuất
Embedded Control Systems
The ADS7806PB provides a practical bridge between analog sensors and embedded controllers because it supports both parallel and serial data output. Parallel mode can reduce firmware complexity when the host bus timing is compatible, while serial mode can reduce wiring on a compact control board. With one analog input, multiple channels are normally implemented using an external multiplexer, adding acquisition time that must be included in the sampling schedule. The 12-bit code width and 40 kSPS rate fit many embedded control and monitoring loops.
Được đề xuất
Audio and Communications Monitoring
The ADS7806PB can be used for supervisory level monitoring in audio or communications equipment where a control loop samples a slow control voltage rather than a full-bandwidth waveform. Its input ranges cover unipolar 0–5 V signals used by many monitoring circuits, and the documented 72 dB minimum SNAD applies with a 1 kHz input. Because 40 kSPS is unsuitable for high-fidelity audio capture, the converter should be reserved for gain, supply, temperature, or status monitoring rather than the primary audio path.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADS7806PB — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADS7807UB | ADS7806P |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 28-pin PDIP | 28-pin PDIP | 28-pin PDIP |
| Resolution | 12 bit | 16 bit | 12 bit |
| Converter Architecture | SAR ADC | SAR ADC | SAR ADC |
| Data Output | Parallel and serial | Parallel and serial | Parallel and serial |
| Supply | Single +5 V | Single +5 V | Single +5 V |
| Reference | Internal or external | Internal or external | Internal or external |
Bảo phân biệt quan trọng
- Direct 12-bit conversion for control and measurement channels (vsADS7807UB)
- Documented 40 kSPS throughput (vsADS7806P)
- Single-supply operation with flexible input ranges (vsADS7807UB)
- Parallel and serial output in one converter (vsADS7807UB)
Ghi chú thiết kế
Use the complete 28-pin PDIP footprint from the manufacturer pinout and route the analog input, reference, and ground network away from digital output and control traces. Place the reference bypass capacitor close to its associated pins and keep the analog ground return compact. The published 72 dB minimum SNAD applies to specified test conditions, so real board noise, reference impedance, and grounding must be evaluated rather than assuming the converter rating alone determines measurement accuracy.
Power the converter from a clean +5 V rail and include the input, output, and reference bypass capacitors specified by the manufacturer. The device can dissipate no more than 35 mW, but external circuitry, regulators, and digital-interface loading contribute additional system consumption. For duty-cycled logging, account for converter startup behavior, reference settling, and the 50-microampere power-down current when calculating battery life.
Do not assume that a 40 kSPS headline rate is the end-to-end sampling rate of a multichannel system. An external multiplexer adds acquisition time, and the input must settle to the required accuracy before conversion. Likewise, do not route a signal outside the selected ±10 V, 0–5 V, or 0–4 V range. Confirm reference selection, conversion timing, output coding, and calibration behavior using the manufacturer datasheet.
Choose between the parallel and serial interface after considering processor bus timing, PCB area, cable length, and firmware complexity. Parallel output may expose more high-speed edges, while serial output can reduce connection count but require correct clocking and data setup. Preserve a continuous return path beneath the device and analog traces where practical, and keep switching regulators and digital clocks spatially separated from the reference and input nodes.
Thông tin tuân thủ
The verified manufacturer and distributor descriptions identify the ADS7806PB as a low-power 12-bit CMOS ADC but do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to this industrial/commercial converter.