Texas Instruments

ADS7806PB - 12-Bit 40 kSPS SAR ADC | Texas Instruments

料号: ADS7806PB ✓ 量产中
+5 V single supply Vdss 50 µA Id 28-pin PDIP Package
最小起订量: 1 |

ADS7806PB 概述

Texas Instruments ADS7806PB is a low-power, 12-bit, single-channel sampling analog-to-digital converter using a successive-approximation-register architecture. It converts one analog input at up to 40 kSPS, supports parallel or serial data output, operates from a single +5 V supply, and is packaged in a 28-pin PDIP. The converter accepts bipolar ±10 V input ranges as well as unipolar 0 V to +5 V and 0 V to +4 V ranges through external circuitry. According to the Texas Instruments product page, acquisition and conversion take no more than 25 microseconds and power dissipation is no more than 35 mW.

A sampling ADC is a data-acquisition component that samples an analog voltage, converts it into a digital code, and transfers that code to a controller, processor, or display system. The ADS7806 belongs to the ADC hierarchy: analog-to-digital converter → sampling ADC → SAR ADC → data-acquisition IC. Its SAR architecture is useful when moderate resolution, predictable conversion behavior, low power, and flexible output interfaces are more important than the throughput and channel density of a high-speed flash converter.

Key features include 12-bit resolution, a 40 kSPS conversion rate, a single analog input, selectable parallel and serial data outputs, and operation from one +5 V supply. The available input ranges are ±10 V, 0 V to +5 V, and 0 V to +4 V. The product page specifies a minimum signal-to-noise-plus-distortion ratio of 72 dB with a 1 kHz input and an acquisition-plus-conversion time of no more than 25 microseconds. These characteristics suit industrial instrumentation, sensor acquisition, laboratory measurement, and embedded control systems.

The converter can use an internal or external reference, while offset and gain adjustments support external trimming with a single supply. Its parallel interface supports direct connection to common microprocessor and microcontroller buses, while the serial interface reduces the number of signal connections and can simplify board routing. The exact interface mode, polarity, timing, and conversion control should be selected from the manufacturer datasheet when integrating the device.

Typical applications include multichannel measurement systems using analog multiplexing, closed-loop industrial controls, laboratory data loggers, instrumentation amplifiers, and sensor-interface modules. In each case, the input network must keep voltages within the selected range, the reference and conversion timing must meet system accuracy requirements, and the digital interface must match the host processor. The 35 mW maximum power specification supports low-power acquisition without requiring a high-output-capability analog reference.

Design with the complete signal chain in mind. Select the input range, reference voltage, and interface mode before assigning PCB signals, then verify acquisition timing against the required sampling rate. Account for the PDIP footprint, analog trace isolation, reference bypass capacitance, and digital-interface levels in the schematic and layout. Request current availability, lifecycle status, and lead time through the Request a Quote form on this page.

This page combines the Texas Instruments device description, package and performance characteristics, sourcing guidance, and application-oriented engineering context. It also identifies the closest documented same-family replacement candidates while preserving the distinction between a true same-package substitution and a device that merely offers similar ADC functionality.

直接替换替代料: ADS7806PB ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: ADS7806PB (相同外形与封装尺寸) ——差异在于 Package, Architecture, Resolution, Supply Voltage, Data Interface.

Texas Instruments
Architecture: SAR (Successive Approximation Register)
Resolution: 12 bits
对比 ADS7806PB →
Texas Instruments
Package: 28-SOIC (0.295 inch, 7.50 mm width)
Architecture: Successive Approximation Register (SAR)
Resolution: 12 bits
Texas Instruments
Package: 28-SOIC (DW)
Architecture: SAR (Successive Approximation Register)
Supply Voltage: 4.75 V to 5.25 V (single +5V)
对比 ADS7806PB →
Texas Instruments
Package: 28-SOIC (DW), 0.295" (7.50 mm) body width
Architecture: SAR (Successive Approximation Register)
Resolution: 16 bits
对比 ADS7806PB →

ADS7807UBE4

✅ 直接替换
Texas Instruments
📦 28-pin PDIP
16 bits · SAR (Successive Approximation Register) · 1 single-ended · 40 kSPS (max) · 25 us (max) · +/-10 V, 0 V to +5 V, 0 V to +4 V · +5 V single supply · 7 mA (typ) / 35 mW (max dissipation)

联系询价

查看数据手册 →

ADS7806P

✅ 直接替换 ⚠️ 规格未核验
Texas Instruments
📦 28-pin PDIP
12 bits · SAR (Successive Approximation Register) · 40 kSPS · 1 · ±10 V, 0 V to +5 V, 0 V to +4 V · +5 V single supply · 35 mW (max) · 50 μW

联系询价

查看数据手册 →

ADS7806PB 最大额定值与电气特性

Converter Type Successive-approximation-register ADC
分辨率 12 bit
采样率 40 kSPS
Number of Inputs 1 analog input
Architecture Sampling CMOS ADC
Data Output Parallel and serial
电源电压 +5 V single supply
Input Ranges ±10 V, 0 V to +5 V, and 0 V to +4 V
Acquisition and Conversion Time 25 µs max
Maximum Power Dissipation 35 mW max
Power-Down Mode Current 50 µA
SNAD 72 dB min with 1 kHz input
Maximum Integral Nonlinearity ±1/2 LSB
Maximum Differential Nonlinearity ±1/2 LSB
Reference Internal or external
封装 28-pin PDIP
Packaging Tube
安装类型 Through-hole

ADS7806PB 28-pin pdip 引脚配置指南

ADS7806PB(28-pin pdip 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。

ADS7806PB 的 28-pin pdip 封装引脚图

暂无详细引脚数据: ADS7806PB.

请参阅 数据手册 以查看完整引脚配置。

典型应用

ADS7806PB 适用于 6 应用s: Industrial Sensor Acquisition, Laboratory Instrumentation, Process Control Systems, Battery-Powered Data Logging, Embedded Control Systems, Audio and Communications Monitoring.

🏭

Industrial Sensor Acquisition

The ADS7806PB is suited to acquiring slowly changing sensor signals in industrial measurement systems because it combines a 12-bit SAR converter with a 40 kSPS sampling rate. Its selectable ±10 V, 0 V to +5 V, and 0 V to +4 V ranges allow conditioning of common industrial inputs through an external network. The 25-microsecond maximum acquisition-and-conversion time supports periodic readings, while parallel output can connect to a controller with sufficient bus capability. Reference quality, input settling, and analog-ground isolation remain critical to maintaining useful accuracy.

🔧

Laboratory Instrumentation

Laboratory instruments can use the ADS7806PB for digitizing measured voltages when 12-bit resolution and 40 kSPS are adequate. Its three documented input ranges support ±10 V measurement channels as well as unipolar 0–5 V and 0–4 V systems. The single +5 V architecture simplifies supply planning, and the 72 dB minimum SNAD provides a defined conversion-performance baseline for a 1 kHz input. For precision instruments, use a stable reference, calibrated input scaling, and shielded routing to preserve that performance.

⚙️

Process Control Systems

The ADS7806PB fits process-control loops that monitor pressure, temperature, position, or level through slower analog channels. A 40 kSPS conversion rate provides ample margin for typical control-loop bandwidth, while the 25-microsecond acquisition-and-conversion limit defines the minimum converter timing budget. The 35 mW maximum device dissipation is useful in distributed control hardware with limited thermal capacity. Select the interface mode and update rate together, then verify propagation through the controller and actuator path.

🔋

Battery-Powered Data Logging

Battery-powered data loggers can benefit from the ADS7806PB because it operates from one +5 V supply, dissipates no more than 35 mW during operation, and draws only 50 microamperes in power-down mode. Its 40 kSPS capability is more than adequate for many temperature, pressure, and environmental sensors sampled at low rates. Duty-cycling the converter can reduce average consumption, although regulator quiescent current, input leakage, and external-sensor power must also be included in the energy budget.

🖥️

Embedded Control Systems

The ADS7806PB provides a practical bridge between analog sensors and embedded controllers because it supports both parallel and serial data output. Parallel mode can reduce firmware complexity when the host bus timing is compatible, while serial mode can reduce wiring on a compact control board. With one analog input, multiple channels are normally implemented using an external multiplexer, adding acquisition time that must be included in the sampling schedule. The 12-bit code width and 40 kSPS rate fit many embedded control and monitoring loops.

🎧

Audio and Communications Monitoring

The ADS7806PB can be used for supervisory level monitoring in audio or communications equipment where a control loop samples a slow control voltage rather than a full-bandwidth waveform. Its input ranges cover unipolar 0–5 V signals used by many monitoring circuits, and the documented 72 dB minimum SNAD applies with a 1 kHz input. Because 40 kSPS is unsuitable for high-fidelity audio capture, the converter should be reserved for gain, supply, temperature, or status monitoring rather than the primary audio path.

推荐产品汇总

ADS7806P Texas Instruments 用于: Industrial Sensor Acquisition, Laboratory Instrumentation, Process Control Systems, Battery-Powered Data Logging, Embedded Control Systems, Audio and Communications Monitoring ADS7807UB Pin-compatible family option with higher resolution 用于: Industrial Sensor Acquisition, Laboratory Instrumentation, Process Control Systems, Battery-Powered Data Logging, Embedded Control Systems, Audio and Communications Monitoring
What is the ADS7806PB?
The ADS7806PB is a Texas Instruments low-power, 12-bit, single-channel SAR analog-to-digital converter rated for 40 kSPS and housed in a 28-pin PDIP. According to the Texas Instruments product page, it supports parallel and serial data outputs, internal or external references, ±10 V, 0 V to +5 V, and 0 V to +4 V input ranges, and operates from one +5 V supply. It is intended for measurement and control systems that require predictable sampling speed without a high-power flash-converter architecture.
What are the key specifications of ADS7806PB that engineers should know?
The ADS7806PB combines 12-bit resolution, a 40 kSPS sampling rate, one analog input, and parallel or serial output in a 28-pin PDIP. According to the Texas Instruments product page, acquisition and conversion require no more than 25 microseconds, maximum power dissipation is 35 mW, and power-down mode consumes 50 microamperes. The converter also supports internal or external references and input ranges of ±10 V, 0 V to +5 V, and 0 V to +4 V, making it suitable for precision acquisition and embedded measurement.
What is the conversion speed of ADS7806PB?
The ADS7806PB performs conversions at up to 40 kSPS, with acquisition and conversion completed in no more than 25 microseconds. According to the Texas Instruments product page, this timing makes the device appropriate for low-bandwidth instrumentation, sensor acquisition, and process-control measurements. System timing should still include external reference settling, input-conditioning, and host-processor handling, so use the manufacturer timing diagrams when calculating end-to-end sample latency.
What input voltage ranges does ADS7806PB support?
The ADS7806PB supports ±10 V, 0 V to +5 V, and 0 V to +4 V input ranges while operating from a single +5 V supply. According to the Texas Instruments product page, the appropriate external input network determines which range is implemented. The range, input impedance, reference arrangement, and allowable source impedance must be evaluated together because incorrect front-end scaling can cause clipping, overload, or conversion errors even when the ADC itself is operating properly.
Does ADS7806PB support parallel and serial interfaces?
Yes, the ADS7806PB supports both parallel and serial data output. According to the Texas Instruments product page, parallel output suits direct connection to processors with compatible bus timing, while serial output can reduce connection count and simplify routing on compact boards. The selected interface mode determines which device pins carry conversion results and control signals, so configure the host interface and board routing from the manufacturer datasheet rather than treating the two modes as electrically interchangeable.
Where can I download the ADS7806PB datasheet PDF?
The ADS7806PB datasheet is available through the official Texas Instruments ADS7806 product page at https://www.ti.com/product/ADS7806 and the manufacturer datasheet link at https://www.ti.com/lit/gpn/ADS7806. The datasheet is the authoritative source for the complete pin configuration, electrical characteristics, input circuit, timing diagrams, reference options, and interface timing. Use the package-specific ordering information to confirm that the PDIP variant matches the PCB footprint before releasing a design.
Where is the ADS7806PB pinout?
The ADS7806PB pinout is found in the pin-configuration section of the official Texas Instruments ADS7806 datasheet at https://www.ti.com/lit/gpn/ADS7806. The part uses a 28-pin PDIP package, and the datasheet identifies analog, reference, control, and digital-output connections. Assign PCB nets directly from that table, including exact signal names, power connections, and any reserved or control pins; do not infer the complete 28-pin map from a generic ADC symbol.
What power does ADS7806PB consume?
The ADS7806PB dissipates no more than 35 mW during operation according to the Texas Instruments product page, and its power-down mode current is 50 microamperes. These values make the converter suitable for low-power measurement systems and portable test equipment. Actual board power depends on the supply voltage, interface activity, reference circuit, and external components, so calculate the complete analog and digital power budget rather than relying only on the converter maximum.
What accuracy does ADS7806PB provide?
The ADS7806PB provides a minimum signal-to-noise-plus-distortion ratio of 72 dB with a 1 kHz input and maximum integral and differential nonlinearities of ±1/2 LSB. According to the Texas Instruments product page, these figures characterize 12-bit conversion performance. Overall measurement accuracy also depends on reference accuracy, input-network scaling, noise, grounding, and calibration, so use the manufacturer error and calibration sections when setting the system error budget.
Is ADS7806PB suitable for sensor and instrumentation applications?
Yes, the ADS7806PB is suitable for low-bandwidth sensor and instrumentation acquisition because it combines a 12-bit SAR ADC, 40 kSPS sampling, selectable input ranges, and a single +5 V supply. According to the Texas Instruments product page, acquisition and conversion take no more than 25 microseconds and maximum device dissipation is 35 mW. Its parallel or serial output supports connection to either a conventional processor interface or a lower-pin-count embedded control system.
ADS7806PB vs ADS7807UB: which is the better drop-in choice?
The ADS7807UB is the closest documented alternative because the ADS7806 family is described as pin-compatible with the 16-bit ADS7807 and the comparison material identifies consistent terminals and packages. The key difference is resolution: ADS7806PB provides 12-bit conversion, whereas ADS7807UB provides 16-bit conversion. Confirm the exact suffix, package, timing, reference configuration, and interface behavior in the manufacturer documentation before replacing an existing design.
What can replace ADS7806PB?
ADS7807UB is the principal same-family replacement candidate identified by the manufacturer’s statement that ADS7806 is pin-compatible with the 16-bit ADS7807. It can suit designs needing greater resolution, but its 16-bit performance differs from the ADS7806PB’s 12-bit conversion. The available cross-reference information does not establish five or more same-package alternatives, so request manufacturer cross-reference support or use the TI cross-reference search for additional qualified candidates.
When should I choose ADS7806PB over ADS7807UB?
Choose ADS7806PB when 12-bit resolution and 40 kSPS sampling are sufficient and the design benefits from the lower-resolution device’s established 12-bit interface behavior. Choose ADS7807UB when the system needs the family’s 16-bit resolution and the associated acquisition and conversion characteristics meet the accuracy requirement. Both decisions should follow a review of input range, reference source, timing, digital protocol, and the exact package suffix rather than relying on resolution alone.
Is ADS7806PB pin-compatible with ADS7807UB?
The ADS7806 family is described as pin-compatible with the ADS7807, and comparison information identifies consistent terminals and packages for the relevant PDIP variants. The primary engineering difference is resolution: ADS7806PB is a 12-bit converter, while ADS7807UB is a 16-bit converter. Treat compatibility as a starting point for review, then verify power sequencing, conversion timing, reference behavior, digital output coding, and calibration requirements in the datasheets before production use.
Where can I buy ADS7806PB and check price and lead time?
Use the Request a Quote form on this page to request the current price, stock status, lead time, and tube quantity for ADS7806PB. Commercial availability can change by package suffix and market conditions, so request the exact ordering code ADS7806PB rather than a related ADS7806 variant. The form also allows buyers to confirm production volume, lifecycle status, and any required traceability or delivery documentation.
What is the price of ADS7806PB?
The current commercial terms for ADS7806PB should be requested through the Request a Quote form on this page. The structured price fields on this page update separately from technical content, while the Request a Quote form confirms the unit price, quantity breaks, stock status, and expected lead time for the exact 28-pin PDIP tube ordering code. Request quantity information for prototype, production, and scheduled-build requirements.
What is the lead time and stock status for ADS7806PB?
Current stock status and lead time for ADS7806PB should be confirmed through the Request a Quote form on this page. Include the required order quantity, target delivery date, and whether the order requires a tube-packaged or otherwise specified presentation of the 28-pin PDIP device. Because inventory and manufacturing schedules fluctuate, treat any historical market indication as non-binding until a quotation is issued.

工程参考数据: ADS7806PB ——对比、设计指导和合规信息。

选型指南

Choose the ADS7806PB when a system needs a low-power, 12-bit, 40 kSPS SAR ADC with one +5 V supply, selectable ±10 V, 0–5 V, or 0–4 V input ranges, and flexible parallel or serial output. Its 25-microsecond maximum conversion time and 35 mW maximum dissipation suit instrumentation, process control, and battery-powered logging where higher throughput is unnecessary. Choose ADS7807UB when the board can use the same family footprint but the measurement chain benefits from 16-bit rather than 12-bit resolution; verify conversion timing, reference behavior, output coding, and calibration before substitution. ADS7806P may be considered for the same 12-bit family when its exact ordering suffix and packing arrangement match the design, but the ordering table must be used to prevent suffix errors. Because the verified cross-reference results do not establish five qualified same-package alternatives, avoid substituting an SOIC or different-pin-count ADC without a PCB redesign and timing review.

与替代料对比

参数 本产品 ADS7807UB ADS7806P
Brand Texas Instruments Texas Instruments Texas Instruments
Package 28-pin PDIP 28-pin PDIP 28-pin PDIP
Resolution 12 bit 16 bit 12 bit
Converter Architecture SAR ADC SAR ADC SAR ADC
Data Output Parallel and serial Parallel and serial Parallel and serial
Supply Single +5 V Single +5 V Single +5 V
Reference Internal or external Internal or external Internal or external

关键差异点

  • Direct 12-bit conversion for control and measurement channels (对比 ADS7807UB)
  • Documented 40 kSPS throughput (对比 ADS7806P)
  • Single-supply operation with flexible input ranges (对比 ADS7807UB)
  • Parallel and serial output in one converter (对比 ADS7807UB)

设计说明

Use the complete 28-pin PDIP footprint from the manufacturer pinout and route the analog input, reference, and ground network away from digital output and control traces. Place the reference bypass capacitor close to its associated pins and keep the analog ground return compact. The published 72 dB minimum SNAD applies to specified test conditions, so real board noise, reference impedance, and grounding must be evaluated rather than assuming the converter rating alone determines measurement accuracy.

Power the converter from a clean +5 V rail and include the input, output, and reference bypass capacitors specified by the manufacturer. The device can dissipate no more than 35 mW, but external circuitry, regulators, and digital-interface loading contribute additional system consumption. For duty-cycled logging, account for converter startup behavior, reference settling, and the 50-microampere power-down current when calculating battery life.

Do not assume that a 40 kSPS headline rate is the end-to-end sampling rate of a multichannel system. An external multiplexer adds acquisition time, and the input must settle to the required accuracy before conversion. Likewise, do not route a signal outside the selected ±10 V, 0–5 V, or 0–4 V range. Confirm reference selection, conversion timing, output coding, and calibration behavior using the manufacturer datasheet.

Choose between the parallel and serial interface after considering processor bus timing, PCB area, cable length, and firmware complexity. Parallel output may expose more high-speed edges, while serial output can reduce connection count but require correct clocking and data setup. Preserve a continuous return path beneath the device and analog traces where practical, and keep switching regulators and digital clocks spatially separated from the reference and input nodes.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The verified manufacturer and distributor descriptions identify the ADS7806PB as a low-power 12-bit CMOS ADC but do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to this industrial/commercial converter.

数据核验日期: 2026-11-14 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

ADS7806PB datasheet ADS7806PB pinout ADS7806PB datasheet pdf ADS7806PB specifications Texas Instruments ADS7806PB ADS7806PB 12 bit ADC ADS7806PB 40 kSPS ADS7806PB 28-PDIP ADS7806PB replacement ADS7806PB vs ADS7807UB ADS7806PB application circuit ADS7806PB price

相关元器件 & 术语

Texas Instruments ADS7806PB ADS7806 ADS7806P ADS7807UB analog-to-digital converter ADC sampling ADC successive-approximation register SAR ADC data-acquisition IC single-channel ADC 12-bit resolution 40 kSPS conversion rate parallel data output serial data output single +5 V supply ±10 V input range 0 V to +5 V input range 0 V to +4 V input range internal reference external reference signal-to-noise-plus-distortion ratio SNAD 28-pin PDIP PDIP package through-hole package power dissipation power-down mode industrial instrumentation process control sensor acquisition battery-powered data logging
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情