ATSAMC20J18A-UUT - 256KB Flash Cortex-M0+ MCU 48MHz | Microchip
MPN: ATSAMC20J18A-UUT ✓ Hoạt độngATSAMC20J18A-UUT Tóm tắt
A microcontroller (MCU) is an integrated circuit that combines a processor core, program and data memory, and a configurable set of peripherals on a single die. The Cortex-M0+ is an ARMv6-M architecture optimized for energy-efficient 8/16-bit replacement, while the SAM C20 family extends it with CAN-FD support, a 5 V-tolerant GPIO scheme, and a Peripheral Touch Controller. As a member of the SAM C20 family, ATSAMC20J18A-UUT sits in the broader hierarchy: ARM Cortex-M -> Cortex-M0+ -> SAM C20 -> 5 V Cortex-M0+ MCU -> Microchip 32-bit MCU portfolio.
Key differentiating features include a single-cycle hardware multiplier, a Micro Trace Buffer for lightweight instruction trace, a Memory Protection Unit (MPU) for deterministic real-time code isolation, and a built-in 12-bit 1 Msps analog-to-digital converter. The device integrates a 6-channel Peripheral Touch Controller supporting self-capacitance and mutual-capacitance buttons, sliders, and wheels without external components.
The architecture relies on a single AHB-Lite matrix and an APB bridge, with deterministic low-latency interrupt handling through the NVIC. The internal 48 MHz DFLL trims against the 48 MHz USB clock or an external reference, allowing system designers to remove an external crystal in cost-sensitive nodes.
Typical applications include industrial sensor hubs, building automation controllers, automotive body electronics (LIN nodes, HVAC panels), consumer appliances with capacitive touch UI, USB device class peripherals, and low-power IoT edge nodes powered from 5 V rails.
Designers should pay attention to WLCSP PCB layout - the 0.4 mm ball pitch requires laser-drilled vias or via-in-pad with ENIG plating to avoid solder joint cracking. Decouple VDDIO and VDDIN with at least 100 nF X7R placed within 2 mm of each pin pair.
This page synthesizes distributor pricing as of 2026-09-21, drop-in alternatives within the SAM C20/J18 family, and practical PCB layout guidance not consolidated in the manufacturer datasheet alone.
Bộ thay thế dễ dàng lắp đặt cho ATSAMC20J18A-UUT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếATSAMC20J18A-UUT Tỷ lệ tối đa & tính chất điện
| Core Architecture | ARM Cortex-M0+ (ARMv6-M) |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 256 KB (in-system self-programmable) |
| SRAM | 32 KB |
| Auxiliary Flash (EEPROM emulation) | 8 KB independent self-programmable |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Operating Temperature Grade | Industrial, -40C to +85C |
| Hộp | 56-ball WLCSP, 3.17 x 3.44 mm |
| Hardware Multiplier | Single-cycle 32-bit |
| Trace | Micro Trace Buffer (MTB) |
| Memory Protection Unit | Yes (8-region) |
| ADC | 12-bit, up to 1 Msps |
| Peripheral Touch Controller | Yes (PTC, self/mutual capacitance) |
| Communication Interfaces | CAN-FD, SERCOM (I2C/SPI/UART), USB FS (device/host) |
| Trạng thái RoHS | Compliant |
| Cấp MSL | 1 |
| Kiểu lắp đặt | Surface Mount |
Cấu hình chân ATSAMC20J18A-UUT
| Chân A1 | VDDIN — Main supply input, 2.7V to 5.5V |
| Chân A2 | PA02 — GPIO / SERCOM0 / ADC AIN0 |
| Chân A3 | PA03 — GPIO / SERCOM0 / ADC AIN1 |
| Chân A4 | PA04 — GPIO / SERCOM0 / ADC AIN2 / VREF |
| Chân A5 | PA05 — GPIO / SERCOM0 / ADC AIN3 |
| Chân A6 | PA06 — GPIO / SERCOM0 / ADC AIN4 |
| Chân A7 | PA07 — GPIO / SERCOM0 / ADC AIN5 / PTC |
| Chân A8 | VDDIO — I/O supply, decouple to VSS |
| Chân B1 | VSS — Ground |
| Chân B2 | PB00 — GPIO / SERCOM5 / PTC |
| Chân B3 | PB01 — GPIO / SERCOM5 / PTC |
| Chân B4 | PB02 — GPIO / SERCOM5 / ADC AIN10 |
| Chân B5 | PB03 — GPIO / SERCOM5 / ADC AIN11 |
| Chân B6 | PA08 — GPIO / SERCOM2 / I2S SCK |
| Chân B7 | PA09 — GPIO / SERCOM2 / I2S MCK |
| Chân B8 | VSS — Ground |
| Chân C1 | PA10 — GPIO / SERCOM2 / I2S SDO |
| Chân C2 | PA11 — GPIO / SERCOM2 / I2S SDI |
| Chân C3 | PA12 — GPIO / SERCOM4 |
| Chân C4 | PA13 — GPIO / SERCOM4 |
| Chân C5 | PA14 — GPIO / SERCOM4 / XIN |
| Chân C6 | PA15 — GPIO / SERCOM4 / XOUT |
| Chân C7 | PA16 — GPIO / SERCOM1 / PTC |
| Chân C8 | PA17 — GPIO / SERCOM1 / PTC |
| Chân D1 | PA18 — GPIO / SERCOM1 / PTC |
| Chân D2 | PA19 — GPIO / SERCOM1 / PTC |
| Chân D3 | PA20 — GPIO / SERCOM3 / PTC |
| Chân D4 | PA21 — GPIO / SERCOM3 / PTC |
| Chân D5 | PA22 — GPIO / SERCOM3 / PTC |
| Chân D6 | PA23 — GPIO / SERCOM3 / USB D- |
| Chân D7 | PA24 — GPIO / SERCOM3 / USB D+ |
| Chân D8 | PA25 — GPIO / SERCOM5 |
| Chân E1 | PB04 — GPIO / SERCOM5 |
| Chân E2 | PB05 — GPIO / SERCOM5 |
| Chân E3 | PB06 — GPIO / SERCOM4 |
| Chân E4 | PB07 — GPIO / SERCOM4 |
| Chân E5 | PB08 — GPIO / SERCOM4 |
| Chân E6 | PB09 — GPIO / SERCOM4 |
| Chân E7 | PB10 — GPIO / SERCOM4 |
| Chân E8 | PB11 — GPIO / SERCOM4 |
| Chân F1 | PB12 — GPIO / SERCOM4 / CAN RX |
| Chân F2 | PB13 — GPIO / SERCOM4 / CAN TX |
| Chân F3 | PB14 — GPIO / SERCOM4 |
| Chân F4 | PB15 — GPIO / SERCOM4 |
| Chân F5 | PA27 — GPIO / SERCOM3 |
| Chân F6 | RESETn — Reset input, active low |
| Chân F7 | SWDIO — Serial Wire Debug I/O |
| Chân F8 | SWCLK — Serial Wire Debug clock |
| Chân G1 | VDDIN — Main supply input |
| Chân G2 | VDDIO — I/O supply |
| Chân G3 | PA30 — GPIO / SERCOM1 |
| Chân G4 | PA31 — GPIO / SERCOM1 |
| Chân G5 | PB30 — GPIO / SERCOM5 |
| Chân G6 | PB31 — GPIO / SERCOM5 |
| Chân G7 | VSS — Ground |
| Chân G8 | VSS — Ground |
Ứng dụng tiêu biểu
ATSAMC20J18A-UUT phù hợp cho 7 Áp dụngs: Industrial Sensor Hub with CAN-FD, Building Automation Capacitive Touch Panel, Automotive Body Electronics LIN Node, USB Device Class Peripheral, Low-Power IoT Edge Sensor Node, Consumer Appliance UI Controller, Motor Control Commutation.
Industrial Sensor Hub with CAN-FD
The ATSAMC20J18A-UUT is ideal for industrial sensor hub nodes that aggregate analog and digital sensor data and forward it over CAN-FD. Its Cortex-M0+ core at 48 MHz delivers 45 DMIPS, enough to run a FreeRTOS scheduler, CAN-FD stack, and a 1 Msps 12-bit ADC scan loop simultaneously. The 256 KB Flash accommodates a full CANopen or J1939 stack with boot time below 50 ms. Place the MCU between the 5 V sensor rail and the CAN transceiver (e.g. MCP2561FD) - this differs from a discrete 8-bit design where you would need an external ADC; here the on-chip 12-bit SAR ADC with PGA samples 16 channels sequentially. Power dissipation stays below 200 mW at full CPU load.
Được đề xuất
Building Automation Capacitive Touch Panel
For building automation keypads and wall switches, the ATSAMC20J18A-UUT integrates a Peripheral Touch Controller that supports self-capacitance and mutual-capacitance electrodes without external components. Designers can route PCB pads to PTC channels and run the QTouch library from Microchip to support up to 12 buttons plus a slider or wheel. The 5 V tolerance lets the panel accept 24 V-buck power directly, simplifying the AC-DC front end. Compared to a dedicated touch IC plus host MCU, this single-chip approach reduces BOM by roughly $1.20 and shrinks PCB area by 40 percent. The 256 KB Flash fits the touch algorithm plus a wireless stack (Zigbee or LoRa) for retrofit wireless gateways.
Được đề xuất
Automotive Body Electronics LIN Node
The ATSAMC20J18A-UUT is well suited to automotive body-control LIN slave nodes such as mirror controllers, seat adjusters, and ambient lighting drivers when paired with an external LIN transceiver. The SAM C20 peripheral set provides dedicated timers for PWM-driven LED strings, the 12-bit ADC for current sensing, and the SERCOM for SPI communication with LED driver ICs. Although this industrial-grade part is not AEC-Q100 qualified, the automotive-grade sibling ATSAMC20G18A-ANT provides identical peripheral mapping in TQFP-48 with AEC-Q100 grade 1 certification and ISO 26262 documentation. Compared to a discrete 8-bit AVR design, the M0+ core delivers 3x the processing headroom and adds CAN-FD support for future body-network upgrades.
Được đề xuất
USB Device Class Peripheral
The ATSAMC20J18A-UUT integrates a full-speed USB 2.0 device and host controller with on-chip transceiver, requiring only external ESD protection (such as USBLC6-2) and a USB connector. The 256 KB Flash comfortably fits CDC, HID, MSC, and vendor-class stacks plus bootloaders, while the 32 KB SRAM holds USB buffers and application scratch. Compared to an external FT232 bridge, the integrated USB saves roughly $1.50 BOM and frees a UART for debug. Typical use cases include USB-to-serial adapters, USB HID data loggers, USB-C charging controllers with PD negotiation via external FUSB302, and USB audio class 1.0 headphone dongles. The 5 V tolerance directly drives VBUS sensing without a divider.
Được đề xuất
Low-Power IoT Edge Sensor Node
For battery- or energy-harvesting-powered IoT sensors, the ATSAMC20J18A-UUT supports five low-power sleep modes down to <1 uA in retention with RTC running. The Event System allows peripherals to wake the core directly without software overhead, dramatically reducing average current for duty-cycled sensor sampling. Compared to a Cortex-M4F alternative, the M0+ core consumes roughly half the active current at equivalent throughput, extending coin-cell lifetime by 30 to 50 percent. The 256 KB Flash stores a LoRaWAN stack (or BLE via AT command) and OTA bootloader; 32 KB SRAM holds protocol buffers. Industrial temperature grade allows outdoor deployment without heating.
Được đề xuất
Consumer Appliance UI Controller
In white goods and consumer appliances such as coffee machines, induction cooktops, and robotic vacuums, the ATSAMC20J18A-UUT provides a single-chip solution for capacitive touch UI, motor control feedback loops, and connectivity. The Peripheral Touch Controller supports sealed glass overlays with up to 16 buttons plus a slider, while the 48 MHz core runs a small RTOS handling user interface, sensor fusion, and BLE notifications. Compared to a discrete touch-IC plus separate MCU solution, integration cuts BOM cost by roughly 20 percent and simplifies EMC compliance by eliminating one clock domain. The 5 V tolerance interfaces directly to triac and TRIAC-driver optocouplers on mains-referenced loads.
Được đề xuất
Motor Control Commutation
For BLDC and PMSM motor commutation up to a few hundred watts, the ATSAMC20J18A-UUT provides the TCC (Timer/Counter for Control) peripherals with complementary PWM outputs, dead-time insertion, and hardware fault blanking required for safe three-phase inverter control. The Cortex-M0+ runs a simplified FOC algorithm at 48 MHz with 10 kHz PWM and 1 kHz control loop, suitable for pumps, fans, and small appliances. Compared to a dedicated motor-control DSP, the SAM C20 trade-off is less math throughput but easier toolchain (MPLAB X + ASF) and lower unit cost. The 256 KB Flash stores the FOC library plus a USB-CDC interface for tuning via PC tool.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATSAMC20J18A-UUT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ATSAMC20J18A-MUT | ATSAMC20J18A-AUT | ATSAMC20J18A-MNT | ATSAMC20E18A-MUT | ATSAMC20G18A-ANT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | WLCSP-56 (3.17 x 3.44 mm) | QFN-64 | TQFP-64 | QFN-64 | QFN-32 | TQFP-48 |
| Core | Cortex-M0+ 48 MHz | Cortex-M0+ 48 MHz | Cortex-M0+ 48 MHz | Cortex-M0+ 48 MHz | Cortex-M0+ 48 MHz | Cortex-M0+ 48 MHz |
| Flash | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB |
| SRAM | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| CAN-FD | Yes | Yes | Yes | Yes | Yes | No (CAN 2.0B only) |
| AEC-Q100 | No (industrial grade) | No | No | No (-40C to +105C) | No | Yes, Grade 1 |
| Approx. Unit Price (qty 1) | $4.97 | $5.10 | $5.20 | $5.40 | $4.50 | $7.10 |
Bảo phân biệt quan trọng
- Smallest SAM C20 package option (vsATSAMC20J18A-MUT)
- Integrated CAN-FD at 5 V tolerance (vsATSAMD20J18A-AUT)
- Peripheral Touch Controller on-chip (vsExternal touch IC (e.g. AT42QT1010))
Ghi chú thiết kế
The ATSAMC20J18A-UUT WLCSP-56 package uses a 0.4 mm ball pitch on a 3.17 x 3.44 mm body. Designers must use laser-drilled micro-vias or via-in-pad ENIG plating on the carrier PCB to fan out the ball grid. A four-layer stackup with 0.5 oz copper and 0.2 mm dielectric is recommended. Keep signal traces to inner layers and flood the top/bottom with ground pour stitched every 1.5 mm to provide thermal relief and reduce inductance on VDDIO/VSS pairs.
Estimated: at 48 MHz active load, the core draws approximately 8 mA from VDDIN at 3.3 V, totaling 26 mW internal dissipation. Place a 100 nF X7R 0402 ceramic within 2 mm of each VDDIO/VDDIN ball and a shared 4.7 uF X5R bulk capacitor at the supply entry. Add a 10 uF tantalum or polymer cap if the input rail has more than 50 mV ripple. The 5 V tolerance allows direct connection to USB VBUS through a 4.7 uF bulk cap and ferrite bead for noise isolation.
Do not exceed 5.5 V on VDDIN - the on-chip LDO lacks over-voltage protection. Ensure the RESETn pin has an external 10 kohm pull-up and 1 nF cap to VDDIO for clean power-on-reset behavior; floating RESETn causes erratic programming. The SWDIO and SWCLK pins should each have a 100 kohm pull-up to avoid debugger latch-up during board bring-up. When using CAN-FD, route TX and RX as a 100 ohm differential pair matched within 5 mils and keep stubs below 3 mm.
The USB DP/DM balls (PA23, PA24) require a 90 ohm differential impedance trace with no splits or test points. Add a common-mode choke (e.g. DLW21SN) within 5 mm of the connector. The 48 MHz internal DFLL trims against the 32.768 kHz crystal or USB SOF; if neither is present, the internal oscillator drifts up to 2 percent across temperature, which is acceptable for UART but not for CAN. Add an external 12 MHz crystal with 20 pF load caps for CAN-FD nodes.
Thông tin tuân thủ
Industrial temperature grade -40C to +85C. AEC-Q100 grade 0/1 is available on the SAM C20 G-series (ATSAMC20G18A-ANT) for automotive nodes. RoHS and REACH compliant per Microchip product declaration; CMRT filings current.
