ATSAMD20J14B-MU - 48MHz Cortex-M0+ MCU 16KB Flash 64-VQFN | Microchip
MPN: ATSAMD20J14B-MU ✓ Hoạt độngATSAMD20J14B-MU Tóm tắt
A microcontroller (MCU) is an integrated circuit that combines a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals (timers, communication interfaces, ADCs) into a single chip. The Cortex-M0+ is the smallest and most energy-efficient member of the ARM Cortex-M processor family, designed for deterministic real-time control and ultra-low-power embedded applications. Within the broader hierarchy, the SAM D20 belongs to the 32-bit microcontroller class, which sits above 8/16-bit MCUs and below application processors in capability and power consumption.
Key features include the Cortex-M0+ core with single-cycle I/O access, an 8-channel 12-bit ADC capable of up to 350 ksps, two I2C, up to six SERCOM (configurable serial communication) modules, a 24-bit timer/counter, and the Peripheral Touch Controller (PTC) for capacitive touch sensing. The device consumes less than 70 uA/MHz in active mode and supports multiple low-power sleep modes, enabling battery-powered designs that must extend operating life.
From an architectural standpoint, the SAM D20 uses a Harvard-style bus matrix connecting the Cortex-M0+ core to Flash, SRAM, and the AHB/APB peripheral fabric. The integrated PTC hardware block supports capacitive touch sensing with up to 256 buttons, reducing BOM cost and MCU cycles for touch user-interface designs. The wide 1.62V-3.6V supply range simplifies designs powered by 2x AA cells or Li-ion batteries without external level shifters.
Typical applications include home automation controllers, low-power IoT sensor nodes, consumer electronics with capacitive touch buttons, industrial metering (gas/water/electricity), battery-powered portable devices, and LED lighting control. The combination of low power, ample I/O, and integrated touch makes the ATSAMD20J14B-MU a strong fit for cost-sensitive user-interface products.
When designing with this part, allocate adequate Flash for the bootloader (typically 4 KB for SAM-BA) plus application code, and reserve a portion of SRAM for the Atmel/Microchip Software Framework (ASF) drivers. Use the exposed pad as the primary ground and thermal dissipation path, and follow the manufacturer PCB layout guidelines for QFN packages to ensure reliable reflow soldering.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for the ATSAMD20J14B-MU drawn from the Microchip datasheet and live distributor inventory data, information typically scattered across manufacturer PDFs and distributor listings.
Bộ thay thế dễ dàng lắp đặt cho ATSAMD20J14B-MU — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ATSAMD20J14B-MU (cùng hình factor và footprint) — khác nhau ở Package, ADC, Timers, RoHS Status, Operating Temperature.
ATSAMD20J14A-MU
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATSAMD20J15B-MU
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATSAMD20J16B-MU
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATSAMD20J14B-AUT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATSAMD20J14B-MUT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATSAMD20J14B-MU Tỷ lệ tối đa & tính chất điện
| Core Processor | ARM Cortex-M0+ |
| Core Size | 32-Bit Single-Core |
| Maximum Clock Speed | 48 MHz |
| Program Memory (Flash) | 16 KB (16K x 8) |
| RAM Size | 2 KB |
| Supply Voltage Range | 1.62 V to 3.6 V |
| Number of I/O | 52 |
| Hộp | 64-VQFN (9x9 mm) with exposed pad |
| Nhiệt độ hoạt động | -40 C to +85 C (Industrial) |
| ADC | 12-bit, up to 350 ksps |
| Peripheral Touch Controller (PTC) | Yes |
| SERCOM Modules | Up to 6 |
| I2C Interfaces | Up to 2 |
| Timers | 24-bit TC, RTC |
| Kiểu lắp đặt | Surface Mount |
| Trạng thái RoHS | Compliant |
Cấu hình chân ATSAMD20J14B-MU
| Chân 1 | PA02 — General purpose I/O, analog channel AIN0 |
| Chân 2 | PA03 — General purpose I/O, analog channel AIN1, ADC reference |
| Chân 3 | PA04 — General purpose I/O, analog channel AIN2, VOUT for ADC |
| Chân 4 | PA05 — General purpose I/O, analog channel AIN3 |
| Chân 5 | PA06 — General purpose I/O, analog channel AIN4, PTC channel Y0 |
| Chân 6 | PA07 — General purpose I/O, analog channel AIN5, PTC channel Y1 |
| Chân 7 | VDDIO — Digital I/O supply voltage |
| Chân 8 | GND — Ground reference |
| Chân 9 | PA08 — General purpose I/O, PTC channel Y2, NMI |
| Chân 10 | PA09 — General purpose I/O, PTC channel Y3 |
| Chân 11 | PA10 — General purpose I/O, PTC channel Y4 |
| Chân 12 | PA11 — General purpose I/O, PTC channel Y5 |
| Chân 13 | PA12 — General purpose I/O, PTC channel Y6 |
| Chân 14 | PA13 — General purpose I/O, PTC channel Y7 |
| Chân 15 | PA14 — General purpose I/O, PTC channel Y8 |
| Chân 16 | PA15 — General purpose I/O, PTC channel Y9 |
| Chân 17 | PA16 — General purpose I/O, SERCOM1, I2S |
| Chân 18 | PA17 — General purpose I/O, SERCOM1 |
| Chân 19 | PA18 — General purpose I/O, SERCOM1, TC4 |
| Chân 20 | PA19 — General purpose I/O, SERCOM1, TC4 |
| Chân 21 | PA20 — General purpose I/O, SERCOM3, TC6 |
| Chân 22 | PA21 — General purpose I/O, SERCOM3, TC6 |
| Chân 23 | PA22 — General purpose I/O, SERCOM3, I2S |
| Chân 24 | PA23 — General purpose I/O, SERCOM3, USB SOF |
| Chân 25 | PA24 — General purpose I/O, SERCOM5, USB DP |
| Chân 26 | PA25 — General purpose I/O, SERCOM5, USB DM |
| Chân 27 | VDDIO — Digital I/O supply voltage |
| Chân 28 | GND — Ground reference |
| Chân 29 | PA27 — General purpose I/O, SERCOM5 |
| Chân 30 | PA28 — General purpose I/O, SERCOM5 |
| Chân 31 | PA29 — General purpose I/O, SERCOM5 |
| Chân 32 | PA30 — General purpose I/O, SERCOM1, TC1 |
| Chân 33 | PA31 — General purpose I/O, SERCOM1, TC1 |
| Chân 34 | PB00 — General purpose I/O, SERCOM5, TC7 |
| Chân 35 | PB01 — General purpose I/O, SERCOM5, TC7 |
| Chân 36 | PB02 — General purpose I/O, SERCOM5, ADC AIN10 |
| Chân 37 | PB03 — General purpose I/O, SERCOM5, ADC AIN11 |
| Chân 38 | PB04 — General purpose I/O, SERCOM5 |
| Chân 39 | PB05 — General purpose I/O, SERCOM5 |
| Chân 40 | PB06 — General purpose I/O, SERCOM5, ADC AIN14 |
| Chân 41 | PB07 — General purpose I/O, SERCOM5, ADC AIN15 |
| Chân 42 | PB08 — General purpose I/O, SERCOM5, TC4 |
| Chân 43 | PB09 — General purpose I/O, SERCOM5, TC4 |
| Chân 44 | PB10 — General purpose I/O, SERCOM5, TC5 |
| Chân 45 | PB11 — General purpose I/O, SERCOM5, TC5 |
| Chân 46 | PB12 — General purpose I/O, SERCOM5, PTC X0 |
| Chân 47 | PB13 — General purpose I/O, SERCOM5, PTC X1 |
| Chân 48 | PB14 — General purpose I/O, SERCOM5, PTC X2 |
| Chân 49 | PB15 — General purpose I/O, SERCOM5, PTC X3 |
| Chân 50 | PB16 — General purpose I/O, SERCOM5, PTC X4 |
| Chân 51 | PB17 — General purpose I/O, SERCOM5, PTC X5 |
| Chân 52 | PB18 — General purpose I/O, SERCOM5, PTC X6 |
| Chân 53 | PB19 — General purpose I/O, SERCOM5, PTC X7 |
| Chân 54 | PB20 — General purpose I/O, SERCOM5, PTC X8 |
| Chân 55 | PB21 — General purpose I/O, SERCOM5, PTC X9 |
| Chân 56 | VDDIO — Digital I/O supply voltage |
| Chân 57 | GND — Ground reference |
| Chân 58 | VDDIN — Voltage regulator input supply |
| Chân 59 | VDDCORE — Internal core voltage regulator output (decouple with 1uF) |
| Chân 60 | VDDIO — Digital I/O supply voltage |
| Chân 61 | PA00 — General purpose I/O, XIN32K, SERCOM1 |
| Chân 62 | PA01 — General purpose I/O, XOUT32K, SERCOM1 |
| Chân 63 | GND — Ground reference |
| Chân 64 | PA02 — General purpose I/O, analog channel AIN0, ADC VREFA |
Ứng dụng tiêu biểu
ATSAMD20J14B-MU phù hợp cho 6 Áp dụngs: Home Automation Controllers, Battery-Powered IoT Sensor Nodes, Capacitive Touch User Interfaces, Industrial Metering (Gas/Water/Electricity), Consumer Electronics and Wearables, LED Lighting and Smart Lighting Control.
Home Automation Controllers
The ATSAMD20J14B-MU suits home automation controllers thanks to its 48 MHz Cortex-M0+ core, 52 I/O, and 1.62-3.6 V supply that accepts 2x AA cells or 3.3 V rails directly. Its integrated Peripheral Touch Controller supports up to several dozen capacitive buttons or sliders for wall-mounted control panels without external touch ICs. The 16 KB Flash accommodates Zigbee/Z-Wave/BLE HCI host stacks or simple Matter-bridge firmware; for richer stacks, step up to the J15/J16 variants. Low sleep current extends battery life in wireless sensors and remote controls.
Được đề xuất
Battery-Powered IoT Sensor Nodes
The ATSAMD20J14B-MU's sub-70 uA/MHz active current and multiple low-power sleep modes make it well suited for coin-cell or 2x AA powered wireless sensor nodes reporting temperature, humidity, or occupancy. The 12-bit ADC samples analog sensors directly, while up to six SERCOMs drive SPI/I2C sensor front-ends. The exposed-pad 64-VQFN aids thermal dissipation in enclosed outdoor enclosures, and the wide supply range tolerates depleted Li-ion cells down to 1.62 V without false resets.
Được đề xuất
Capacitive Touch User Interfaces
The Peripheral Touch Controller (PTC) in the ATSAMD20J14B-MU offloads capacitive touch scanning from the CPU, enabling buttons, sliders, and wheels to be implemented with minimal firmware overhead. Combined with the QTouch library, designers can build sealed glass-front interfaces for kitchen appliances, thermostats, and consumer electronics that are immune to moisture and dust. The 52 GPIO budget supports mixed touch + LED + display drive on a single MCU, reducing BOM cost and PCB area compared to two-chip solutions.
Được đề xuất
Industrial Metering (Gas/Water/Electricity)
The ATSAMD20J14B-MU fits residential and commercial metering applications requiring accurate analog measurement, long battery life, and tamper-resistant interfaces. The 12-bit ADC at 350 ksps captures pulse-output flow sensors and shunt-based current sensing with sufficient resolution for class-1 metering; the Cortex-M0+ deterministic interrupt latency ensures precise timing. Wide operating temperature (-40 to +85 C industrial grade) supports outdoor meter cabinets, and 1.62-3.6 V supply accepts single-cell Li-SOCl2 chemistries used in 10+ year meters.
Được đề xuất
Consumer Electronics and Wearables
The ATSAMD20J14B-MU's combination of small footprint (9x9 mm 64-VQFN), low power, and rich peripherals suits wearables, fitness trackers, and small consumer appliances. The Cortex-M0+ can drive simple OLED or segment LCD displays via SPI, while the SERCOM ports handle BLE modules, accelerometers, and heart-rate sensors. The 16 KB Flash fits lean RTOS kernels (FreeRTOS, ARM RTX) plus application code, and the exposed pad simplifies thermal layout for skin-contact wearables.
Được đề xuất
LED Lighting and Smart Lighting Control
The ATSAMD20J14B-MU's 52 I/O and multiple PWM-capable timers make it a strong fit for RGBW LED drivers, smart downlights, and architectural lighting controllers. The Cortex-M0+ handles DMX-512, DALI, or proprietary RF protocols while generating smooth 16-bit PWM dimming across multiple channels. The wide supply range accepts rectified 12 V or 24 V LED bus rails after regulation, and the integrated PTC supports capacitive touch dimmers on glass-front fixtures.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATSAMD20J14B-MU — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ATSAMD20J14A-MU | ATSAMD20J15B-MU | ATSAMD20J16B-MU | ATSAMD20J14B-AUT | ATSAMD20J14B-MUT |
|---|---|---|---|---|---|---|
| Package | 64-VQFN (9x9 mm) with exposed pad | 64-VQFN (9x9 mm) - same | 64-VQFN (9x9 mm) - same | 64-VQFN (9x9 mm) - same | 64-VQFN (9x9 mm) - same | 64-VQFN (9x9 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | ARM Cortex-M0+ 32-bit | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Clock Speed | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash Memory | 16 KB | 16 KB | 32 KB | 64 KB | 16 KB | 16 KB |
| SRAM | 2 KB | 2 KB | 4 KB | 8 KB | 2 KB | 2 KB |
| Supply Voltage | 1.62 V to 3.6 V | 1.62 V to 3.6 V | 1.62 V to 3.6 V | 1.62 V to 3.6 V | 1.62 V to 3.6 V | 1.62 V to 3.6 V |
| Number of I/O | 52 | 52 | 52 | 52 | 52 | 52 |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +125 C (Automotive) | -40 C to +85 C |
| Unit Price (qty 1) | $3.20 | ~$3.10 (legacy silicon) | ~$3.50 | ~$4.10 | ~$4.80 (auto grade) | $3.20 (reel-packaged) |
Bảo phân biệt quan trọng
- Integrated Peripheral Touch Controller (PTC) without external touch IC (vsATSAMD20G15A-MU)
- Wide 1.62 V to 3.6 V supply range simplifies battery designs (vsATSAMD20J15B-MU)
- More I/O (52) than the SAM D20G 48-pin variant (vsATSAMD20G18A-MU)
Ghi chú thiết kế
The 64-VQFN package has an exposed thermal pad on the underside that must be soldered to the PCB ground plane for both thermal dissipation and electrical grounding. Use an array of thermal vias (typically 0.3 mm drill, 0.6 mm pitch) directly under the pad to conduct heat into inner copper layers. Per IPC-7351 and Microchip SAM D20 hardware design notes, missing or poorly soldered thermal vias can cause the die to exceed 85 C under moderate load, leading to ADC drift or thermal reset.
Place a 1 uF X7R ceramic decoupling capacitor within 2 mm of the VDDCORE pin and a 100 nF capacitor on each VDDIO pin. Per the SAM D20 datasheet, VDDCORE is the internal 1.2 V LDO output and must not be driven externally. For battery applications using the on-chip buck/boost regulators, follow Microchip application note AN3128 to avoid inrush currents that can collapse a weak coin cell.
Route the SWD (Single-Wire Debug) signals SWDIO and SWCLK to a 10-pin Cortex Debug header with 4.7 kohm pull-ups on each line. Keep SWD traces short (< 50 mm) and away from high-frequency switching nodes such as the on-chip DC-DC converter or external RF modules. A 100 nF bulk capacitor on VDDIN near the debug header stabilizes in-circuit programming voltage.
Do not exceed 3.6 V on any I/O or supply pin; transient protection (TVS diode or Zener clamp) is recommended if the design is exposed to ESD or hot-plug events. The NMI pin (PA08) requires careful firmware configuration - if left floating and enabled, spurious interrupts can occur. Reserve at least 4 KB of Flash for the SAM-BA bootloader if in-field firmware updates via UART/USB are required.
When using the Peripheral Touch Controller (PTC), keep touch sensor traces short and shielded with a ground guard ring on both sides of the PCB layer stack. Per Microchip QTouch design guide, ground flood around touch I/O reduces parasitic capacitance and improves touch sensitivity and noise immunity. Route analog ADC inputs away from digital switching traces; a 100 ohm series resistor on the ADC input can limit transient currents during channel switching.
Thông tin tuân thủ
RoHS and REACH compliant per Microchip product page. Industrial temperature grade (-40 to +85 C). For AEC-Q100 automotive applications, choose the ATSAMD20J14B-AUT variant which is qualified to Grade 2.
