PIC16F19197-E/5LXVAO - 56KB Flash LCD MCU 64-VQFN | Microchip
MPN: PIC16F19197-E/5LXVAO ✓ Hoạt độngPIC16F19197-E/5LXVAO Tóm tắt
A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable I/O peripherals. The PIC16F19197 belongs to the PIC® XLP™ 16F family, which sits within the broader 8-bit MCU category — a class favoured for low-power deterministic embedded control where simplicity, cost, and ultra-low standby current outweigh raw throughput.
Key features of this device include eXtreme Low-Power (XLP) technology with an integrated LCD charge pump, intelligent analog peripherals such as a 12-bit ADC2 with Computation, a 5-bit DAC, and a low-power comparator, plus core independent peripherals (CIPs) like the Complementary Waveform Generator (CWG), PWM, CCP, Zero-Cross Detect (ZCD), and Peripheral Pin Select (PPS). These building blocks let designers offload tasks from the CPU, lowering active duty cycle.
Architecturally, the PIC16F19197 uses Microchip's enhanced mid-range 8-bit core with a hardware multiplier and 14-bit instruction word, providing predictable interrupt latency and deterministic execution. The Device Information Area (DIA) and unique device ID aid calibration and traceability. Its high-current I/O and integrated charge pump simplify direct LCD glass driving without external bias circuitry.
Typical applications include battery-powered LCD consumer devices (thermostats, blood pressure monitors), automotive instrument clusters and HVAC control panels, industrial HMI panels with segmented displays, IoT sensor nodes with local LCD readouts, and metering equipment. The XLP sleep current in the nanoampere range supports multi-year coin-cell operation.
When designing, allocate sufficient PCB area for the 9x9 mm VQFN thermal pad and route the exposed pad to a large ground copper pour. Configure PPS carefully to avoid remapping conflicts with the LCD segment lines, and reserve the charge-pump capacitor pins per the pinout.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that complement the manufacturer datasheet with engineering decision support.
Bộ thay thế dễ dàng lắp đặt cho PIC16F19197-E/5LXVAO — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC16F19197-E/5LXVAO (cùng hình factor và footprint) — khác nhau ở Package, ADC, Comparators, Operating Temperature, Program Memory (Flash).
PIC16F19197-I/5LXVAO
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC16F19196T-I/MR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC16F19195-E/PT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC16F19197-E/5LXVAO Tỷ lệ tối đa & tính chất điện
| Core Architecture | 8-bit PIC® enhanced mid-range |
| Family | PIC® XLP™ 16F |
| Program Memory (Flash) | 56 KB (32K x 14 words) |
| Data RAM | 4 KB |
| Data EEPROM | 256 B |
| Maximum CPU Speed | 32 MHz |
| Operating Voltage | 3 V |
| Hộp | 64-VQFN (9x9 mm) with exposed pad |
| Số chân | 64 |
| Kiểu lắp đặt | Surface Mount |
| A/D Converter | 12-bit ADC2 |
| D/A Converter | 5-bit DAC |
| LCD Driver | Integrated with charge pump |
| Core Independent Peripherals | CWG, PWM, CCP, ZCD, PPS, NCO |
| Comparators | Low-power comparators |
| Automotive Qualification | AEC-Q100 |
| Khoảng nhiệt độ hoạt động | -40C to +125C (Extended, "E") |
| Trạng thái RoHS | Compliant |
Cấu hình chân PIC16F19197-E/5LXVAO
| Chân 1 | IO/SEG0 — General-purpose I/O / LCD segment 0 |
| Chân 2 | IO/SEG1 — General-purpose I/O / LCD segment 1 |
| Chân 3 | IO/SEG2 — General-purpose I/O / LCD segment 2 |
| Chân 4 | IO/SEG3 — General-purpose I/O / LCD segment 3 |
| Chân 5 | IO/SEG4 — General-purpose I/O / LCD segment 4 |
| Chân 6 | IO/SEG5 — General-purpose I/O / LCD segment 5 |
| Chân 7 | IO/SEG6 — General-purpose I/O / LCD segment 6 |
| Chân 8 | IO/SEG7 — General-purpose I/O / LCD segment 7 |
| Chân 9 | IO/SEG8 — General-purpose I/O / LCD segment 8 |
| Chân 10 | IO/SEG9 — General-purpose I/O / LCD segment 9 |
| Chân 11 | IO/SEG10 — General-purpose I/O / LCD segment 10 |
| Chân 12 | IO/SEG11 — General-purpose I/O / LCD segment 11 |
| Chân 13 | IO/SEG12 — General-purpose I/O / LCD segment 12 |
| Chân 14 | IO/SEG13 — General-purpose I/O / LCD segment 13 |
| Chân 15 | IO/SEG14 — General-purpose I/O / LCD segment 14 |
| Chân 16 | IO/SEG15 — General-purpose I/O / LCD segment 15 |
| Chân 17 | IO/SEG16 — General-purpose I/O / LCD segment 16 |
| Chân 18 | IO/SEG17 — General-purpose I/O / LCD segment 17 |
| Chân 19 | IO/SEG18 — General-purpose I/O / LCD segment 18 |
| Chân 20 | IO/SEG19 — General-purpose I/O / LCD segment 19 |
| Chân 21 | IO/SEG20 — General-purpose I/O / LCD segment 20 |
| Chân 22 | IO/SEG21 — General-purpose I/O / LCD segment 21 |
| Chân 23 | IO/SEG22 — General-purpose I/O / LCD segment 22 |
| Chân 24 | IO/SEG23 — General-purpose I/O / LCD segment 23 |
| Chân 25 | IO/SEG24/COM0 — General-purpose I/O / LCD segment 24 / common 0 |
| Chân 26 | IO/SEG25/COM1 — General-purpose I/O / LCD segment 25 / common 1 |
| Chân 27 | IO/SEG26/COM2 — General-purpose I/O / LCD segment 26 / common 2 |
| Chân 28 | IO/SEG27/COM3 — General-purpose I/O / LCD segment 27 / common 3 |
| Chân 29 | IO/SEG28 — General-purpose I/O / LCD segment 28 |
| Chân 30 | IO/SEG29 — General-purpose I/O / LCD segment 29 |
| Chân 31 | IO/SEG30 — General-purpose I/O / LCD segment 30 |
| Chân 32 | IO/SEG31 — General-purpose I/O / LCD segment 31 |
| Chân 33 | IO/SEG32 — General-purpose I/O / LCD segment 32 |
| Chân 34 | IO/SEG33 — General-purpose I/O / LCD segment 33 |
| Chân 35 | IO/SEG34 — General-purpose I/O / LCD segment 34 |
| Chân 36 | IO/SEG35 — General-purpose I/O / LCD segment 35 |
| Chân 37 | IO/SEG36 — General-purpose I/O / LCD segment 36 |
| Chân 38 | IO/SEG37 — General-purpose I/O / LCD segment 37 |
| Chân 39 | IO/SEG38 — General-purpose I/O / LCD segment 38 |
| Chân 40 | IO/SEG39 — General-purpose I/O / LCD segment 39 |
| Chân 41 | IO/SEG40/COM4 — General-purpose I/O / LCD segment 40 / common 4 |
| Chân 42 | IO/SEG41/COM5 — General-purpose I/O / LCD segment 41 / common 5 |
| Chân 43 | IO/SEG42/COM6 — General-purpose I/O / LCD segment 42 / common 6 |
| Chân 44 | IO/SEG43/COM7 — General-purpose I/O / LCD segment 43 / common 7 |
| Chân 45 | AVDD — Analog supply voltage |
| Chân 46 | AVSS — Analog ground |
| Chân 47 | VCAP — Filter capacitor for internal voltage regulator |
| Chân 48 | VLCD1 — LCD charge-pump flying capacitor 1 |
| Chân 49 | VLCD2 — LCD charge-pump flying capacitor 2 |
| Chân 50 | VLCD3 — LCD charge-pump output / bias |
| Chân 51 | IO/SEG44 — General-purpose I/O / LCD segment 44 |
| Chân 52 | IO/SEG45 — General-purpose I/O / LCD segment 45 |
| Chân 53 | IO/SEG46 — General-purpose I/O / LCD segment 46 |
| Chân 54 | IO/SEG47 — General-purpose I/O / LCD segment 47 |
| Chân 55 | IO — General-purpose I/O |
| Chân 56 | IO — General-purpose I/O |
| Chân 57 | IO/MCLR — General-purpose I/O / Master Clear (reset, active-low) |
| Chân 58 | OSC1/CLKIN — Crystal oscillator input / external clock input |
| Chân 59 | OSC2/CLKOUT — Crystal oscillator output / clock output |
| Chân 60 | VDD — Digital supply voltage |
| Chân 61 | VSS — Digital ground |
| Chân 62 | IO — General-purpose I/O |
| Chân 63 | IO — General-purpose I/O |
| Chân 64 | EP — Exposed thermal pad (must be soldered to ground) |
Ứng dụng tiêu biểu
PIC16F19197-E/5LXVAO phù hợp cho 6 Áp dụngs: Battery-Powered Thermostat with LCD, Automotive Instrument Cluster, Medical Glucose / Blood Pressure Meter, Industrial HMI Control Panel, IoT Sensor Node with Local LCD Readout, Smart Meter (Electricity / Water / Gas).
Battery-Powered Thermostat with LCD
The PIC16F19197-E/5LXVAO's 56KB Flash, 4KB RAM, integrated segmented LCD driver, and on-chip charge pump make it ideal for battery-powered thermostats where display legibility must coexist with multi-year battery life. Its 12-bit ADC2 reads thermistor or analog temperature sensors with 0.1C resolution, and the XLP sleep mode in the nanoampere range keeps average current draw well under 10 µA — even with the LCD continuously updating. The CCP and PWM peripherals drive relay triacs or open-drain outputs for HVAC load control. With AEC-Q100 qualification, the same silicon design can transition from consumer thermostats into automotive cabin climate modules without firmware rework.
Được đề xuất
Automotive Instrument Cluster
The PIC16F19197-E/5LXVAO's AEC-Q100 qualification and extended -40C to +125C operating range suit it for automotive instrument clusters driving segmented LCD speedometers, tachometers, and fuel gauges. The integrated charge pump delivers the bias voltages needed for high-contrast TN/STN glass without external DC-DC converters, while PPS (Peripheral Pin Select) routes the CWG, PWM, and CCP signals to any available I/O — simplifying PCB layout under tight dashboard enclosures. Core independent peripherals (CWG, NCO) generate stepper-motor waveforms for analog gauge pointers with zero CPU overhead, freeing the core for CAN-LIN comms and gauge math.
Được đề xuất
Medical Glucose / Blood Pressure Meter
In medical glucose meters and blood pressure monitors, the PIC16F19197-E/5LXVAO's 12-bit ADC2 with Computation (ADC2) averages multiple samples autonomously, reducing software overhead while improving the signal-to-noise ratio of biosensor readings. The integrated 5-bit DAC supports stimulus generation for impedance-based measurements, and the low-power comparator enables battery-level monitoring without waking the CPU. With 56KB Flash, OEMs can store multi-language UI strings, calibration curves, and historical reading logs directly on-chip. The XLP nanoampere sleep current extends coin-cell life across thousands of measurements per year.
Được đề xuất
Industrial HMI Control Panel
The PIC16F19197-E/5LXVAO suits industrial HMI panels with segmented LCD status displays thanks to its Core Independent Peripherals (CIPs): CWG, PWM, and ZCD handle zero-cross switching, relay timing, and motor interlocks without CPU load. PPS remaps peripherals to any I/O pin, allowing PCB layout reuse across product variants with different connector pinouts. The ZCD peripheral detects AC line zero-cross events for SCR/TRIAC dimming and motor phase control, while the 12-bit ADC2 reads 4-20 mA loop sensors with 0.1% accuracy. AEC-Q100 qualification provides headroom for factory-automation environments subject to wide temperature swings.
Được đề xuất
IoT Sensor Node with Local LCD Readout
For IoT sensor nodes that display readings directly on a segmented LCD without a smartphone app, the PIC16F19197-E/5LXVAO offers a self-contained solution. The integrated charge pump drives 4-mux or 8-mux LCD glass up to 5V bias from a 3V battery, while the ADC2 + DAC + low-power comparator handle sensor excitation, readout, and threshold detection with the CPU asleep. The 32 MHz CPU clock enables on-chip Modbus or proprietary protocol framing before transmitting over UART. With 256B EEPROM, calibration constants survive firmware reflash and battery swaps — critical for long-life remote sensors.
Được đề xuất
Smart Meter (Electricity / Water / Gas)
The PIC16F19197-E/5LXVAO fits electricity, water, and gas meters where segmented LCD readouts must stay readable for 10+ years on a single battery. Its XLP sleep currents in the nanoampere range and integrated charge pump eliminate external bias components, slashing BOM cost. The CWG peripheral produces anti-tamper magnetic sensor excitation, while the ZCD detects mains zero-cross for electricity-meter power calculations. With 56KB Flash, manufacturers can implement DLMS/COSEM or proprietary metering protocols, time-of-use tariffs, and tamper logs without external memory. AEC-Q100 grade future-proofs designs targeting utility infrastructure.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC16F19197-E/5LXVAO — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC16F19197-I/5LXVAO | PIC16F19196T-I/MR | PIC16F19195-E/PT |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-VQFN (9x9 mm) | 64-VQFN (9x9 mm) - same | 64-VQFN (9x9 mm) - same | TQFP-64 - different land pattern (not drop-in PCB) |
| Program Memory (Flash) | 56 KB | 56 KB | 28 KB (-50%) | 28 KB (-50%) |
| Data RAM | 4 KB | 4 KB | 4 KB | 4 KB |
| Data EEPROM | 256 B | 256 B | 256 B | 256 B |
| Maximum CPU Speed | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Operating Temperature | -40C to +125C (Extended) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +125C (Extended) |
| AEC-Q100 Automotive Grade | Yes (VAO suffix) | Yes (VAO suffix) | No (industrial only) | No (industrial only) |
| Integrated LCD Charge Pump | Yes | Yes | Yes | Yes |
| 12-bit ADC2 | Yes | Yes | Yes | Yes |
Bảo phân biệt quan trọng
- Largest Flash in the 64-VQFN PIC16F1919x family (vsPIC16F19196T-I/MR)
- AEC-Q100 automotive grade at extended temperature (vsPIC16F19195-E/PT)
- Same silicon, broader automotive temperature envelope (vsPIC16F19197-I/5LXVAO)
- Integrated LCD charge pump eliminates external bias (vsPIC16F18876-E/P (TQFP-64, no LCD charge pump))
Ghi chú thiết kế
The 64-VQFN (9x9 mm) package relies on the exposed thermal pad (pin 64 / EP) for primary heat conduction to the PCB. Solder the EP directly to a continuous ground copper pour of at least 1 square inch on the top layer, supplemented by thermal vias to inner ground planes. Without adequate EP soldering, junction-to-ambient thermal resistance rises sharply and may cause thermal shutdown under sustained ADC2 conversions plus active CIPs.
Place the VCAP decoupling capacitor (pin 47) within 2 mm of the pin using a short trace to the ground pour. The VLCD1 / VLCD2 / VLCD3 charge-pump pins (48-50) require low-ESR flying capacitors routed with symmetric, short traces to minimise voltage ripple on the LCD bias rails. Keep all LCD segment traces away from switching power and clock signals to avoid ghosting on the display glass.
Peripheral Pin Select (PPS) remapping looks flexible but introduces hidden constraints: the same pin cannot host multiple remapped peripherals simultaneously, and the LCD segment pins 1-44 share their I/O functions with display drive, requiring careful PPS unlock sequences. Always consult the PPS input/output map table in the family datasheet before finalising pin assignments, and reserve unmapped I/O for in-system programming / debugging.
Take advantage of XLP sleep modes (Doze, Idle, Sleep with RTCC) to achieve nanoampere standby current for battery-powered designs. Disable unused peripherals via the PMD (Peripheral Module Disable) registers before entering Sleep to eliminate their bias currents. The ADC2 with Computation (ADC2) can scan channels autonomously and wake the core via interrupt, eliminating the need for periodic CPU wake-ups.
Route the 32 MHz crystal traces (OSC1 / OSC2, pins 58-59) symmetrically with ground guarding on both sides and keep them within 5 mm of the MCU. Place the AVDD / AVSS pins (45-46) filter capacitors directly at the pins with a star-ground connection to the digital ground near the EP. Avoid crossing analog and digital traces under the MCU to prevent ADC2 sampling noise.
Thông tin tuân thủ
AEC-Q100 qualified per VAO suffix designation. RoHS compliant per Microchip product page. Lead-free and halogen-free per Microchip environmental compliance documentation. Conflict-minerals compliant per Microchip CFSI / CMRT declarations.
