ATTINY88-15AZ - 8KB 28-I/O AVR MCU | Microchip Technology
MPN: ATTINY88-15AZ ✓ Hoạt độngATTINY88-15AZ Tóm tắt
An 8-bit microcontroller is a compact embedded-processing IC that executes firmware from embedded Flash memory and reads or writes data through EEPROM and SRAM. The ATTINY88 belongs to the TinyAVR hierarchy: 8-bit AVR microcontroller, reduced instruction computer architecture, and embedded control IC. Its picoPower CMOS design targets efficient automotive control applications where deterministic peripheral operation, low pin count, and integrated nonvolatile memory are valuable.
The device combines 8KB of ISP Flash, 64B of EEPROM, and 512B of SRAM. It provides 28 general-purpose I/O lines, 32 general-purpose working registers, and two flexible timer/counters with compare modes. A 123-instruction instruction set includes most instructions executing in a single clock cycle, supporting responsive control-loop and peripheral-timing tasks while retaining the simple programming model of the AVR architecture.
The ATTINY88-15AZ uses the -15AZ suffix for a 15 MHz device and is identified in automotive documentation as an automotive-quality-grade product. Microchip automotive documentation states that the ATtiny88 family was developed according to ISO-TS-16949 grade 1 requirements. The device is offered in the 32-terminal gull-wing TQFP package, with package code HTQFP.
Typical automotive uses include compact body or climate-control modules, sensor interfaces, actuator controllers, lighting modules, and general vehicle electronics. Its 28 I/O lines can support multiple digital inputs, outputs, and communication peripherals without requiring a larger package, while the timers support timing and compare-based functions.
PCB design should preserve the datasheet's pin multiplexing and programming interface requirements. Provide the specified power, decoupling, reset, and programming connections, and verify external peripheral timing against the 15 MHz operating limit. Automotive production should also apply the manufacturer’s qualification, traceability, and change-control requirements.
This page combines the manufacturer’s ATtiny88 documentation with package, interface, lifecycle, programming, and replacement guidance. It also distinguishes true same-footprint alternatives from merely similar AVR devices, helping engineers assess PCB reuse, memory differences, timing compatibility, and automotive qualification before approving a substitution.
Bộ thay thế dễ dàng lắp đặt cho ATTINY88-15AZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ATTINY88-15AZ (cùng hình factor và footprint) — khác nhau ở Package, SRAM, Product Type, Flash Memory, Architecture.
ATTINY88-15MZ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ATTINY88-AU
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATTINY88-AUR
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →ATTINY48-15AZ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ATTINY48-AU
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →ATTINY88-15AZ Tỷ lệ tối đa & tính chất điện
| Product Type | 8-bit AVR RISC microcontroller |
| Architecture | AVR RISC-based CMOS |
| Maximum Clock Speed | 15 MHz |
| Program Flash Memory | 8KB |
| EEPROM Memory | 64B |
| SRAM | 512B |
| General-Purpose I/O Lines | 28 |
| General-Purpose Working Registers | 32 |
| Timer/Counter Count | 2 |
| Instruction Count | 123 |
| Architecture | Advanced RISC architecture |
| Hộp | 32-pin TQFP |
| Package Code | HTQFP |
| Terminal Count | 32 |
| Package Shape | Square |
| Terminal Form | Gull wing |
| Temperature Grade | Automotive |
| Manufacturing Quality Standard | ISO-TS-16949 grade 1 |
| Programming Interface | In-system programming (ISP) |
Hướng dẫn cấu hình chân ATTINY88-15AZ square
Cấu hình chân cho ATTINY88-15AZ (square gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho ATTINY88-15AZ.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ATTINY88-15AZ phù hợp cho 6 Áp dụngs: Automotive Climate-Control Module, Vehicle Sensor Interface, Automotive Lighting Controller, Compact Actuator Controller, Automotive Body Control Submodule, Standalone Automotive Programming Module.
Automotive Climate-Control Module
The ATTINY88-15AZ fits a compact vehicle climate-control module because its 28 general-purpose I/O lines can support multiple switch inputs, sensor interfaces, actuator outputs, and status indicators without moving to a larger controller package. Its two flexible timer/counters with compare modes support periodic sampling and actuator timing, while 512B of SRAM supports working state and 64B of EEPROM provides limited nonvolatile configuration storage. The 8KB ISP Flash footprint is sufficient for focused control firmware, although the final image must be size-checked. Its automotive-grade designation and 15 MHz operation make it appropriate for a compact electronic control unit that requires deterministic I/O handling and simple field programming.
Được đề xuất
Vehicle Sensor Interface
ATTINY88-15AZ can consolidate several digital and analog-adjacent sensor signals in a vehicle sensor interface because the device provides 28 general-purpose I/O lines and two timer/counters. The timer/counter compare functions can support pulse-width sensing, periodic sampling, timeout management, and sensor-health timing, while the AVR RISC architecture executes most instructions in one clock cycle at the 15 MHz operating rate. Its 8KB Flash stores compact acquisition and filtering code, 512B of SRAM handles active measurements, and 64B of EEPROM can retain limited calibration or configuration values. The automotive grade, 32-pin TQFP package, and ISP programming support fit compact modules requiring controlled production programming.
Được đề xuất
Automotive Lighting Controller
The ATTINY88-15AZ suits a compact automotive lighting controller where multiple lamps, status outputs, buttons, and diagnostic lines must be managed in one package. Its 28 general-purpose I/O lines reduce the need for external logic, and the two timer/counters can establish blink, fade, or timeout intervals without continuous software delays. At 15 MHz, the AVR RISC processor provides responsive execution for sequencing and fault detection, while 8KB of Flash accommodates a focused lighting routine and 512B of SRAM supports state management. The 32-pin TQFP format simplifies dense multilayer PCB layouts, and the automotive-grade ordering code supports use in qualified vehicle electronics programs.
Được đề xuất
Compact Actuator Controller
ATTINY88-15AZ is well matched to a compact actuator controller that coordinates solenoids, relays, motor-control inputs, and end-stop or feedback signals. Its 28 I/O lines allow multiple actuator channels and sensor inputs to remain on the controller, reducing system size and interconnects. The two timer/counters provide timing references for pulse generation, commutation, or actuator travel limits, while the 15 MHz clock allows the firmware to combine those timing tasks with diagnostic and safety-state checks. The 8KB Flash limit favors compact application code, 512B of SRAM supports live control state, and the 32-pin TQFP package provides a defined automotive-style footprint for production assembly.
Được đề xuất
Automotive Body Control Submodule
ATTINY88-15AZ can serve as a body-control submodule for localized functions such as door-zone input consolidation, switch monitoring, lamp sequencing, and diagnostic signaling. The 28 general-purpose I/O lines provide a useful balance between I/O density and package size, while the two timer/counters support repetitive automotive functions without excessive processor loading. Its 8KB ISP Flash permits compact field-updatable logic, and 64B of EEPROM can preserve a limited set of configuration values. Operating at 15 MHz with the AVR RISC architecture supports timely event handling, while the 32-pin TQFP package and automotive-grade designation fit a qualified distributed vehicle electronics architecture.
Được đề xuất
Standalone Automotive Programming Module
ATTINY88-15AZ can be used in a compact vehicle programming or configuration module that coordinates ISP programming, status indication, and nonvolatile parameter storage. Its 8KB of in-system-programmable Flash can hold a focused programming workflow, while 64B of EEPROM provides a small amount of persistent configuration storage. The 28 I/O lines permit communication, mode selection, and diagnostic signaling, and the two timer/counters can manage activity timing or indicator control. At 15 MHz, firmware can validate commands and manage programming sequences efficiently. The 32-pin TQFP package supports compact board construction, while automotive-grade identification makes the device suitable for qualification within vehicle electronics when the complete module meets its applicable environmental requirements.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATTINY88-15AZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ATTINY88-15MZ | ATTINY88-AU | ATTINY88-AUR | ATTINY48-15AZ | ATTINY48-AU |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 32-TQFP | 32-TQFP | 32-TQFP | 32-TQFP | 32-TQFP | 32-TQFP |
| Program Flash Memory | 8KB | 8KB | 8KB | 8KB | 4KB | 4KB |
Bảo phân biệt quan trọng
- Full 8KB Flash capacity preserves the target firmware envelope (vsATTINY48-15AZ)
- Exact 15 MHz operating designation (vsATTINY88-AU)
- Automotive-grade ordering code for vehicle electronics (vsATTINY88-15MZ)
- High I/O density in a defined 32-pin surface-mount package (vsATTINY88-AUR)
Ghi chú thiết kế
Assign every net from the manufacturer’s 32-pin TQFP pin-description table rather than from a generic ATtiny84 or ATtiny85 footprint. The ATTINY88 uses 28 general-purpose I/O lines, but several terminals also have alternate peripheral functions. Preserve the datasheet-defined locations for power, ground, reset, and ISP signals, route the programming interface to a reachable test pad or connector, and maintain the required decoupling-capacitor placement close to the supply pins.
Do not approve an alternative solely because its package drawing matches. For ATTINY48 alternatives, account for the reduction from 8KB to 4KB of Flash, which can break the compiled image even if the PCB footprint is unchanged. For ATTINY88-AU variants, verify the clock rating, temperature grade, automotive qualification, fuse defaults, and active lifecycle status. A replacement should receive firmware, timing, and in-circuit programming validation before production release.
Use the manufacturer datasheet for the exact supply-voltage range and operating-current limits before designing the power tree. Because the ATTINY88-15AZ combines automotive temperature-grade identification with a 15 MHz clock and 28 I/O lines, the power supply must remain within all DC and transient limits during startup, reset, and peripheral activity. Confirm the external crystal or clock arrangement and programming behavior against the selected clock configuration.
Keep the 15 MHz clock path compact and follow the manufacturer layout guidance for decoupling and signal return paths. Treat I/O pins carrying external vehicle signals as potentially noisy or high-energy interfaces, and place input protection close to the connector. Avoid long traces between the programming header and MCU, and maintain a continuous ground reference beneath the 32-pin TQFP footprint to reduce susceptibility to coupling and timing disturbance.
Thông tin tuân thủ
Microchip automotive documentation states that the ATtiny88 family was developed according to ISO-TS-16949 grade 1 requirements. Separate RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not established.