BCM54640B0KFB Ethernet Interface IC | Broadcom
MPN: BCM54640B0KFB ✗ Cuối đờiBCM54640B0KFB Tóm tắt
An Ethernet interface IC is a semiconductor that integrates the physical-layer transceiver and digital interface functions needed to connect processor, switch, or communications equipment to Ethernet networks. Depending on its exact configuration, this device can support combinations of copper and fiber-facing ports, serial GMII/SGMII links, media-independent interfaces, clocks, and control signals. The BCM54640 family therefore sits within the hierarchy Ethernet interface IC, Ethernet transceiver, network interface controller, interface IC, and integrated circuit.
The main engineering benefit of integrating these functions is reduced component count and a compact connection between a digital Ethernet subsystem and physical media. A system designer can connect the serial interface to a network processor or switch fabric while using the transceiver portion for Ethernet line signaling. This integration can shorten board routing, reduce exposed connector and magnetics complexity, and provide a more standardized interface boundary than a collection of separate PHY and digital-interface components.
The BCM54640B0KFB is identified by Broadcom and is associated with SGMII-based Ethernet connectivity. SGMII is a serial gigabit Ethernet interface commonly used between MAC and PHY devices. Its use allows high-speed data to travel over a compact differential or single-ended implementation depending on the electrical standard, reducing pin count relative to parallel GMII. Engineers must still follow the exact voltage, timing, termination, and layout requirements for the specific Broadcom interface.
Typical uses include access-network equipment, Ethernet switches, routers, network interface cards, industrial Ethernet systems, and communications infrastructure where an integrated multi-port transceiver can simplify board design. The device may also be evaluated in designs requiring a standard SGMII connection between a switching ASIC or packet processor and physical-layer circuitry. Interface voltage levels and pin-level functions must be checked against the host ASIC before layout begins.
A key design consideration is that Ethernet signal integrity depends on controlled impedance, short differential routes, solid return paths, and proper separation from noisy power and digital circuitry. Decoupling, clock cleanliness, magnetics or optical-interface integration, reset behavior, and thermal performance also require verification against the manufacturer documentation. Use the Broadcom BCM54640B0KFB datasheet and its reference design when assigning pins and selecting passive components.
This page combines the available manufacturer and distributor product records, identifies the confirmed same-family BCM54640 naming options, and provides a structured engineering comparison and application guide. It is intended to accelerate initial component screening while directing final footprint, timing, electrical, and lifecycle decisions to the authoritative Broadcom documentation.
Bộ thay thế dễ dàng lắp đặt cho BCM54640B0KFB — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
BCM54640B0KFBG
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
BCM54640B0IFBG
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
BCM54640B0KFB Tỷ lệ tối đa & tính chất điện
| Product Type | Ethernet interface IC |
| Manufacturer | Broadcom |
| Series | BCM54640 |
| Serial Interface | SGMII |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân BCM54640B0KFB standard
Cấu hình chân cho BCM54640B0KFB (standard gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho BCM54640B0KFB.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
BCM54640B0KFB phù hợp cho 6 Áp dụngs: Ethernet Switch Line Cards, Router Network Interfaces, Access Network Equipment, Industrial Ethernet Gateways, Network Interface Cards, Communications Infrastructure Equipment.
Ethernet Switch Line Cards
BCM54640B0KFB is a candidate for an Ethernet switch line card where a switching ASIC requires a compact SGMII link to physical-layer circuitry. Integrating the Ethernet interface into the BCM54640 family can reduce the number of discrete interface devices and shorten sensitive signal paths between the MAC and transceiver sections. Before schematic capture, engineers must confirm the supported port count, copper and fiber media, maximum data rate, and electrical levels against the host ASIC. The PCB should follow the manufacturer reference layout for controlled-impedance SGMII routing, clock distribution, decoupling, and return-path continuity. Thermal and power analysis must also use the exact datasheet operating conditions.
Được đề xuất
Router Network Interfaces
The BCM54640B0KFB can be evaluated for router and communications equipment that connects a network processor to Ethernet physical media through SGMII. The integrated interface approach may reduce board area and component count compared with separate PHY and controller solutions, while preserving a defined serial boundary between high-speed digital logic and Ethernet circuitry. The key selection criteria are supported line rate, media configuration, clock architecture, reset sequencing, and management-register behavior. Use the exact Broadcom documentation to establish timing margins and power requirements, and validate conducted, radiated, and thermal performance before production.
Được đề xuất
Access Network Equipment
BCM54640B0KFB is suitable for initial screening in access-network terminals and aggregation equipment where multiple Ethernet connections and SGMII-based host integration are required. Consolidation of Ethernet interface functions can lower board complexity and simplify firmware control when the selected configuration matches the system's port mix. The design review should verify whether copper, fiber, or both media are required, confirm the supported PHY features, and check startup and reset behavior. Regulatory and deployment targets can make long-term availability important, so lifecycle confirmation and an approved alternate should be obtained before the design reaches production.
Được đề xuất
Industrial Ethernet Gateways
BCM54640B0KFB can support an industrial Ethernet gateway when its SGMII host interface and available transceiver ports align with the gateway's wired communications architecture. A serial high-speed link can simplify connections between an embedded processor and Ethernet hardware, while integrated interface functions can reduce the component count on space-constrained control boards. Industrial designs must confirm the device's operating-temperature grade, isolation requirements, surge and ESD strategy, and long-term supply status. The layout should preserve uninterrupted ground planes beneath SGMII routes and isolate switching power stages and connectors from sensitive interface signals.
Được đề xuất
Network Interface Cards
BCM54640B0KFB is applicable to a network interface card when the host controller exposes the required SGMII clocks and data signals and the card needs a consolidated Ethernet interface solution. The device family can simplify routing relative to parallel legacy interfaces and provide a standardized serial connection to the network processor. Designers must verify lane polarity, reference-clock source, I/O voltage, timing, and supported media against the host ASIC. PCB stack-up and component placement should be treated as part of the signal-integrity design, especially when the card also contains connectors, magnetics, clock sources, and nonisolated power converters.
Được đề xuất
Communications Infrastructure Equipment
BCM54640B0KFB can be assessed for communications infrastructure equipment requiring deterministic Ethernet connectivity between a packet-processing ASIC and physical media. The BCM54640 family's SGMII association makes it relevant to compact, high-speed line-card implementations, provided the exact port and grade configuration is supported. Validation should include interface timing over all voltage and temperature corners, reference-clock jitter tolerance, reset behavior, electromagnetic performance, and fault recovery. For field-deployed equipment, confirm lifecycle status, traceability, date-code controls, and a qualified alternate before freezing the production BOM.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho BCM54640B0KFB — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | BCM54640B0KFBG | BCM54640B0IFBG |
|---|---|---|---|
| Brand | Broadcom | Broadcom | Broadcom |
| Product Family | BCM54640 | BCM54640 | BCM54640 |
Bảo phân biệt quan trọng
- Original Broadcom ordering option (vsBCM54640B0KFBG)
- Alternative BCM54640 family ordering option (vsBCM54640B0IFBG)
- SGMII-focused Ethernet integration (vsBCM54640B0KFBG)
Ghi chú thiết kế
Route SGMII and reference-clock signals on a controlled-impedance board stack-up that matches the Broadcom reference design. Use a continuous reference plane, minimize vias and stubs, and avoid splitting return current beneath high-speed pairs. Keep the clock source and traces away from switching regulators, Ethernet magnetics, and connector-return paths. Confirm trace geometry, spacing, and length behavior from the manufacturer layout because the exact package and interface timing are not stated in the available product records.
Implement the BCM54640B0KFB supply network with the manufacturer-recommended topology, including local high-frequency decoupling, adequate bulk capacitance, and separate filtering paths for noisy and sensitive rails. Place the smallest effective bypass capacitors directly beside the relevant power terminals and provide a low-impedance ground connection. Confirm capacitor voltage ratings, DC-bias effects, startup sequencing, and the device's maximum supply tolerances in the datasheet before finalizing the power tree.
Use the exact Broadcom land pattern and assembly information associated with the BCM54640B0KFB ordering code. Check the pin-one orientation, exposed thermal features, solder-mask and paste details, and any keep-out or via requirements against the package drawing. Do not copy the footprint from BCM54640B0KFBG or BCM54640B0IFBG unless Broadcom confirms that the package suffix is identical. Program the part identifier after placement and verify orientation during electrical inspection.
Avoid assuming that same-family ordering codes are automatically interchangeable. The available records do not quantify the differences between BCM54640B0KFB, BCM54640B0KFBG, and BCM54640B0IFBG, and those differences could involve grade, packing, configuration, or availability. Before substitution, compare the manufacturer ordering tables, pin descriptions, electrical characteristics, package drawings, and lifecycle information. Also verify the reset polarity and clock requirements against the host system.
Thông tin tuân thủ
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations appear in the available product records. Confirm these attributes with Broadcom using the exact ordering code.