BCM5698B0IPBG - 12-Port Gigabit Ethernet Switch | Broadcom
MPN: BCM5698B0IPBG ✓ Hoạt độngBCM5698B0IPBG Tóm tắt
An Ethernet switch is a semiconductor that receives frames on one port, examines addressing information, and forwards traffic to the appropriate destination port. A Layer 2 switch performs this operation at the data-link layer rather than routing packets through the network layer. By integrating 12 Gigabit Ethernet ports into one package, the BCM5698B0IPBG reduces the component count and board complexity required for a multiport Ethernet aggregation point.
The primary documented performance attribute is support for 12 Gigabit Ethernet ports. Gigabit Ethernet corresponds to a nominal 1 Gbit/s network rate per port, allowing the switch fabric to aggregate substantial aggregate traffic when several ports operate simultaneously. The exact forwarding rate, latency, internal memory configuration, host interface, management features, and supported PHY types must be confirmed in the manufacturer datasheet before final system qualification.
The PBG package designation identifies the physical assembly used by this ordering code, but detailed dimensions, pin assignments, thermal limits, and exposed-pad requirements are not stated in the available product records. Engineers should use the BCM5698 datasheet and the package drawing when assigning power, ground, reference-clock, management, and media signals. The B0 revision suffix should also be checked against the latest manufacturer change notices.
Typical deployments include industrial Ethernet switches, factory-floor control networks, access-network aggregation, embedded telecom equipment, and network appliances requiring multiple copper or fiber-facing ports. In these systems, the switch can consolidate several 1 Gbit/s links before forwarding traffic to an uplink, storage system, or controller.
Power delivery, clock quality, thermal management, and signal-integrity layout are critical design considerations. Follow the manufacturer’s recommended decoupling network, provide a stable low-noise reference clock where required, and validate magnetics or PHY integration according to the supported copper-media architecture. Confirm lane ratings, auto-negotiation behavior, and environmental limits on the selected board revision.
This page consolidates the verified port count, Layer 2 function, package designation, sourcing information, replacement constraints, and engineering guidance needed to evaluate the BCM5698B0IPBG for a 12-port Gigabit Ethernet design.
Bộ thay thế dễ dàng lắp đặt cho BCM5698B0IPBG — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
BCM5698B0KPBG
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →BCM5698B0IPBG Tỷ lệ tối đa & tính chất điện
| Product Type | Layer 2 Gigabit Ethernet switch |
| Ethernet Port Count | 12 ports |
| Nominal Ethernet Rate | 1 Gbit/s per port |
| Network Layer | Layer 2 |
| Manufacturer | Broadcom |
| Orderable MPN | BCM5698B0IPBG |
| Revision Code | B0 |
| Package Designation | PBG |
Hướng dẫn cấu hình chân BCM5698B0IPBG pbg
Cấu hình chân cho BCM5698B0IPBG (pbg gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho BCM5698B0IPBG.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
BCM5698B0IPBG phù hợp cho 6 Áp dụngs: Industrial Ethernet Aggregation, Managed Network Appliance, Factory Control Network Gateway, Access Network Uplink Concentrator, Embedded Telecom Equipment, Power and Building Automation.
Industrial Ethernet Aggregation
The Broadcom BCM5698B0IPBG fits an industrial Ethernet aggregation point because it integrates 12 nominal 1 Gbit/s Layer 2 ports in one PBG package. A controller can use the switching fabric to consolidate traffic from machines, sensors, and remote I/O before forwarding it to a plant uplink. The multiport integration reduces the number of discrete switch devices and associated PCB routing. Before design release, confirm the exact temperature grade, copper PHY configuration, clock requirements, power budget, and industrial qualification in the manufacturer documentation.
Được đề xuất
Managed Network Appliance
BCM5698B0IPBG is suitable for a managed network appliance that needs to aggregate twelve Gigabit Ethernet connections while performing Layer 2 forwarding. Its 12-port arrangement provides a practical front-panel scale for access equipment, and the 1 Gbit/s-per-port nominal rate supports common Ethernet endpoints. The system designer must allocate pins and board area for the PBG package, provide the required reference clock and power rails, and validate management, address-table, and traffic-control behavior against the selected firmware and device revision.
Được đề xuất
Factory Control Network Gateway
The BCM5698B0IPBG can serve as the central switching element in a factory control-network gateway, where controllers and machine vision nodes require dedicated Gigabit Ethernet paths. Twelve Layer 2 ports allow local traffic to remain within the switched network while selected traffic reaches a higher-level uplink. Because the product is a switch IC rather than a complete interface module, the enclosure also needs magnetics or supported PHY integration, isolation requirements, clock distribution, thermal provisions, and management software selected for the target system.
Được đề xuất
Access Network Uplink Concentrator
BCM5698B0IPBG is appropriate for an access-network concentrator that combines multiple Gigabit Ethernet service links behind a common uplink. The 12-port Layer 2 architecture gives a compact platform for local subscriber aggregation while maintaining 1 Gbit/s service rates on each nominal port. Implementation requires careful PBG footprint design, specified supply sequencing, low-noise clocking, and a copper-media subsystem compatible with the device’s supported interface configuration. Verify buffering and forwarding performance in the manufacturer datasheet before sizing an uplink beyond individual port rates.
Được đề xuất
Embedded Telecom Equipment
The Broadcom BCM5698B0IPBG can support embedded telecom equipment that requires multiple Layer 2 Ethernet ports for internal routing, service handoff, or test interfaces. Combining twelve Gigabit Ethernet ports in a PBG package simplifies the PCB compared with a design using many single-port devices. Thermal performance and signal integrity remain central because the switch fabric sits close to high-speed PHY, magnetics, and clock circuitry. Validate conducted emissions, isolation, grounding, reference-clock jitter, and startup behavior against the product’s electrical and environmental limits.
Được đề xuất
Power and Building Automation
BCM5698B0IPBG can be evaluated for power and building automation systems that connect controllers, meters, cameras, and access points over separate Gigabit Ethernet links. Twelve Layer 2 ports offer centralized switching in control cabinets or edge gateways and help isolate local traffic from the backbone uplink. The integration must account for the PBG package footprint, the device’s electrical requirements, thermal environment, and supported media interface. Confirm operating-temperature limits and lifecycle commitments before deployment in continuously energized building or utility infrastructure.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho BCM5698B0IPBG — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | BCM5698B0KPBG |
|---|---|---|
| Package | PBG | PBG - same package designation |
| Brand | Broadcom | Broadcom |
| Ethernet Port Count | 12 ports | 12 ports |
| Nominal Port Rate | 1 Gbit/s per port | 1 Gbit/s per port |
| Switching Layer | Layer 2 | Layer 2 |
| Revision Code | B0 | B0 |
| Ordering-Code Difference | I suffix designation | K suffix designation; exact qualification difference requires manufacturer confirmation |
Bảo phân biệt quan trọng
- Documented 12-port integration (vsBCM5698B0KPBG)
- Single-package network aggregation (vsBCM5698B0KPBG)
- B0 revision continuity (vsBCM5698B0KPBG)
Ghi chú thiết kế
Use the manufacturer PBG land pattern and pin-description table as the authority for placement and routing. Keep power and ground connections short, place required bypass capacitors at their designated pins, and preserve the package’s thermal-current path through board copper or other approved heat-spreading features. A high-layer-count PCB may be necessary because a 12-port Gigabit Ethernet design also requires controlled-impedance traces, careful return paths, and separation between sensitive clock or media signals and switching nodes.
Treat the reference clock, management interfaces, and high-speed media connections as separate signal-integrity domains. Follow the manufacturer’s clock topology and impedance guidance, avoid routing the reference clock adjacent to noisy digital nets, and use continuous reference planes where the stackup permits. For copper media, apply the vendor-recommended line geometry, component placement, isolation spacing, and magnetics or PHY interface layout; otherwise nominal 1 Gbit/s compliance may be compromised by reflections, crosstalk, or jitter.
Calculate heat dissipation from the actual input voltage, core current, switching activity, and ambient temperature rather than relying only on nominal port count. Validate the PBG package with the manufacturer’s recommended PCB construction and airflow assumptions, and monitor the hottest locations in a fully populated, worst-case traffic test. Estimated: if the design dissipates 4 W, an assumed 25 C/W junction-to-ambient path would produce about 100 C rise before allowing for copper spreading; this calculation is illustrative and must be replaced with the datasheet thermal model and measured board data.
Do not treat a shared PBG package suffix as sufficient proof of interchangeability. Before substituting BCM5698B0KPBG for BCM5698B0IPBG, compare the ordering table, temperature grade, supply limits, pin functions, clock requirements, PHY configuration, management interfaces, firmware support, and lifecycle notices. After hardware equivalence is established, run traffic, thermal, reset, power-sequencing, and interoperability tests because a package-compatible device can still behave differently at the system level.
Thông tin tuân thủ
Compliance attributes are not stated in the available product records. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status using the current Broadcom product documentation before procurement release.