BCM5762B0KMLG - PCIe GBE MAC/PHY Controller | Broadcom
MPN: BCM5762B0KMLG ✓ Hoạt độngBCM5762B0KMLG Tóm tắt
An Ethernet MAC/PHY controller is a type of interface IC that bridges a computing system and a physical network. The MAC portion manages frame processing and host-facing data transfer, while the PHY handles the electrical signaling required for Gigabit Ethernet. Combining these functions can reduce board-level component count compared with a design that uses separate Ethernet MAC and PHY devices. PCI Express provides the high-speed peripheral link used to exchange data between the controller and the host processor.
The BCM5762B0KMLG is identified as a PCI-E GBE MAC/PHY with DASH 1.0 capability. DASH 1.0 support is significant for systems that need a dedicated hardware-assisted Ethernet path rather than relying only on software-managed networking. Gigabit Ethernet support makes the device applicable to routers, gateways, embedded systems, set-top equipment, and industrial network controllers where a 1 Gb/s network interface is required.
Technical implementation requires careful coordination among the PCIe host interface, Gigabit Ethernet PHY, network magnetics, clocks, and power rails. The device integrates the digital MAC and physical-layer functions, but the external network still requires suitable magnetic coupling, an appropriate Ethernet transformer or PHY interface network, controlled impedance routing, and isolated power as required by the system architecture. Firmware and host drivers must also support the selected controller configuration.
Typical uses include telecommunications access equipment, routers, network appliances, embedded servers, and industrial Ethernet systems. In these applications, the integrated MAC/PHY arrangement can simplify board partitioning while the PCI Express interface provides a conventional host connection. System suitability still depends on the required driver, operating system, network magnetics, thermal environment, and connector implementation.
The main design consideration is verification against the manufacturer datasheet for pin assignments, power sequencing, reference clocks, PHY strap settings, and supported operating modes. Use the datasheet pin-description table when assigning PCB tracks, and preserve the specified high-speed and Ethernet differential-routing geometry to avoid signal-integrity problems.
This page combines the Broadcom device classification, procurement guidance, verified lifecycle information, interface-selection considerations, and engineering notes needed to evaluate the BCM5762B0KMLG for a PCIe Gigabit Ethernet design.
Bộ thay thế dễ dàng lắp đặt cho BCM5762B0KMLG — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếBCM5762B0KMLG Tỷ lệ tối đa & tính chất điện
| Device Type | PCI-E GBE MAC/PHY plus DASH 1.0 |
| Product Category | Telecom interface controller IC |
| Host Interface | PCI Express |
| Ethernet Speed | 1 Gb/s |
| MAC Function | Integrated Gigabit Ethernet MAC |
| PHY Function | Integrated Gigabit Ethernet PHY |
| DASH Support | DASH 1.0 |
| Manufacturer | Broadcom |
Hướng dẫn cấu hình chân BCM5762B0KMLG standard
Cấu hình chân cho BCM5762B0KMLG (standard gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho BCM5762B0KMLG.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
BCM5762B0KMLG phù hợp cho 6 Áp dụngs: Telecommunications Access Equipment, Router and Gateway Interfaces, Industrial Networked Control Systems, Embedded Network Appliances, Network Interface Cards, Security and Video Edge Equipment.
Telecommunications Access Equipment
BCM5762B0KMLG fits access and aggregation equipment that requires a dedicated Gigabit Ethernet path between a host processor and the public or service-provider network. Its integrated PCI-E GBE MAC/PHY reduces the number of separate network-interface devices, while DASH 1.0 provides a hardware-assisted networking option for dedicated traffic processing. The host processor must support the controller through its PCIe interface and appropriate driver, while the board also needs Ethernet magnetics, controlled-impedance routing, and carefully isolated power where required. Design validation should cover throughput, packet handling, thermal behavior, and uninterrupted operation across the intended network load.
Router and Gateway Interfaces
The BCM5762B0KMLG is suitable for a router or gateway that needs multiple high-speed external connections and can allocate a PCIe slot or embedded PCIe lanes to Ethernet traffic. Its 1 Gb/s Gigabit Ethernet capability and integrated MAC/PHY allow the interface to operate without splitting those functions across separate controller devices. DASH 1.0 support can help systems offload selected networking operations from the main processor. Engineering teams should confirm lane availability, device-driver support, interrupt behavior, boot sequencing, and magnetics selection before committing the board layout, because these system-level factors determine whether the controller can deliver predictable routing performance.
Industrial Networked Control Systems
BCM5762B0KMLG can support an industrial controller that must exchange real-time Ethernet traffic with a host processor over PCI Express. Consolidating the Gigabit Ethernet MAC and PHY into one controller simplifies the physical network interface and leaves more board area for sensing, isolation, power conversion, and communications circuitry. For factory equipment, evaluate the controller against the system's operating-temperature range, conducted-noise requirements, network resilience, and availability expectations. The Ethernet magnetics and isolation network must be designed for the intended cable environment, and the controller layout should preserve controlled differential impedance and separation between network and host-side circuitry.
Embedded Network Appliances
BCM5762B0KMLG is appropriate for an embedded appliance that combines compute, storage, or local processing with a Gigabit Ethernet management or service connection. The PCI Express interface fits systems designed around a modern embedded processor, and the integrated MAC/PHY can reduce component count compared with separate controller implementations. DASH 1.0 support may be useful where the system benefits from a dedicated networking path. Before board release, verify processor driver support, PCIe configuration requirements, reference-clock provisioning, boot behavior, thermal margins, and software support for the intended operating system. A production design should also include network-loopback and sustained-throughput testing under realistic packet sizes.
Network Interface Cards
BCM5762B0KMLG can be evaluated for a PCI Express network interface card intended to add a 1 Gb/s Ethernet connection to a host platform. Its combined MAC/PHY architecture suits a compact add-in card, while DASH 1.0 provides a hardware-assisted feature set for systems that need offloaded networking behavior. Realization of the card still depends on the connector, Ethernet transformer or magnetics, isolation, reference clock, power budget, and host-side driver. Mechanical clearance, airflow, and ground-plane continuity also influence reliability. Validate the complete card with sustained traffic, hot-plug requirements if applicable, link negotiation, fault recovery, and electromagnetic-emissions testing before production release.
Security and Video Edge Equipment
BCM5762B0KMLG can serve as the network interface in an edge appliance that moves sensor, camera, or control data toward a centralized service. The 1 Gb/s Ethernet capability supports reliable transfer of typical local traffic, while the integrated MAC/PHY avoids a split controller layout. DASH 1.0 may assist designs that require predictable hardware-assisted networking, although the final benefit depends on host software and system architecture. Security-focused equipment should add appropriate isolation, surge protection, controlled boot behavior, and secure firmware management. Validate sustained transfer rates, latency under congestion, link recovery after cable or peer events, and thermal performance inside the final enclosure rather than relying only on bench-level connectivity tests.
Dữ liệu tham khảo kỹ thuật cho BCM5762B0KMLG — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Manufacturer | Broadcom |
| Device Type | PCI-E GBE MAC/PHY plus DASH 1.0 |
| Host Interface | PCI Express |
| Ethernet Speed | 1 Gb/s |
| MAC Function | Integrated Gigabit Ethernet MAC |
| PHY Function | Integrated Gigabit Ethernet PHY |
| DASH Support | DASH 1.0 |
| Lifecycle Status | Active |
Bảo phân biệt quan trọng
- Integrated Gigabit Ethernet MAC and PHY (vsA standalone MAC and PHY implementation)
- Dedicated PCIe host connectivity (vsA controller using a non-PCIe host interface)
- Hardware-assisted networking feature set (vsA basic Gigabit Ethernet controller without DASH)
Ghi chú thiết kế
Use the Broadcom pin-description table to assign the PCI Express lanes, Gigabit Ethernet differential pairs, reference clocks, reset, power rails, and ground connections. Place the supporting network components and decoupling capacitance according to the manufacturer layout guidance, keeping sensitive traces away from high-current switching paths. Do not infer an equivalent pin assignment from a similar-looking controller because package suffixes can represent different lead maps.
Treat the PCIe and Gigabit Ethernet interfaces as controlled-impedance, high-speed links. Use the stackup and impedance targets specified by the manufacturer and PCB fabricator, avoid unnecessary stubs, provide continuous reference planes, and observe the required pair spacing and routing symmetry. Ethernet magnetic coupling should be placed close to the connector or physical network boundary, with protection components selected to avoid unintended loading of the PHY interface.
Do not treat the Broadcom part number alone as proof of driver or board compatibility. Confirm the host PCIe lane configuration, operating-system support, PHY strap requirements, reference-clock source, reset timing, and power sequence against the datasheet before schematic capture. A controller that enumerates correctly can still show link instability when magnetics, termination, clocking, or thermal conditions are outside the reference design.
Thông tin tuân thủ
Compliance status must be confirmed from the current Broadcom product declaration or product-page documentation for the exact BCM5762B0KMLG ordering code.