CD4060BCN - 14-Stage Counter and Oscillator | onsemi
MPN: CD4060BCN ✓ Hoạt độngCD4060BCN Tóm tắt
A binary counter is a sequential digital circuit that records a number of clock events as binary bits. The CD4060BCN belongs to the CD4000 CMOS logic family and advances on each negative transition of its clock input. Its oscillator can use an external resistor-capacitor network or crystal, while the counter stages provide divided clock outputs for timing and frequency-generation circuits.
The device operates across a 3.0 V to 15 V supply range and features high noise immunity of 0.45 VDD typical. Its asynchronous reset is independent of the clock and returns the counter to zero when the reset input is driven to a logical 1. The integrated oscillator and divider architecture reduce the number of external components required in timer, pulse-generator, and low-frequency clock circuits.
The CD4060BCN uses a ripple-carry implementation, so each internal stage transitions after the preceding stage. This structure is useful when multiple divided frequencies are required, but timing edges at the higher-count outputs include accumulated propagation delay. Clock-driven designs benefit from a clean negative edge at the clock input. When oscillator accuracy or stability is important, component tolerances and parasitic capacitance must be considered alongside the external RC or crystal network.
Typical uses include RC or crystal oscillators, binary frequency dividers, periodic pulse generators, interval timers, low-frequency clock sources, and sequential control systems. The 16-lead PDIP package supports through-hole assembly and prototyping, while its 3.0 V to 15 V operating range accommodates legacy CMOS logic systems operating at 5 V or 15 V.
When designing a divider, confirm that the selected output frequency meets the required timing accuracy and that the reset pulse is clean. Decoupling capacitors should be placed close to the supply pins, and unused counter outputs should remain properly terminated. This page consolidates operating characteristics, drop-in alternatives, comparison data, and application-focused design guidance for CD4060BCN selection.
Bộ thay thế dễ dàng lắp đặt cho CD4060BCN — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với CD4060BCN (cùng hình factor và footprint) — khác nhau ở Logic Family, Supply Voltage Range.
CD4060BC
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
HCF4060BEY
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
HEF4060BP
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
CD4060BEX
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
CD4060BCN Tỷ lệ tối đa & tính chất điện
| Counter Type | 14-stage ripple-carry binary counter |
| Supply Voltage Range | 3.0 V to 15 V |
| Clock Edge | Negative-edge triggered |
| Reset Type | Asynchronous, active-high |
| Noise Immunity | 0.45 VDD typical |
| Counter Output Count | 14 stages |
| Oscillator | On-chip RC or crystal oscillator |
| Logic Family | CD4000 CMOS series |
| Hộp | 16-lead PDIP |
| Package Width | 0.300 in |
| Package Standard | JEDEC MS-001 |
| Kiểu lắp đặt | Through-hole |
Cấu hình chân CD4060BCN
| Chân 1 | OSC1 — Oscillator input and external timing-network connection |
| Chân 2 | OSC2 — Oscillator output and external timing-network connection |
| Chân 3 | MR — Asynchronous master reset input |
| Chân 4 | Q4 — Divided counter output |
| Chân 5 | Q5 — Divided counter output |
| Chân 6 | Q6 — Divided counter output |
| Chân 7 | Q7 — Divided counter output |
| Chân 8 | Q8 — Divided counter output |
| Chân 9 | Q9 — Divided counter output |
| Chân 10 | Q10 — Divided counter output |
| Chân 11 | Q11 — Divided counter output |
| Chân 12 | Q12 — Divided counter output |
| Chân 13 | Q13 — Divided counter output |
| Chân 14 | Q14 — Divided counter output |
| Chân 15 | VSS — Ground reference |
| Chân 16 | VDD — Positive supply input |
Ứng dụng tiêu biểu
CD4060BCN phù hợp cho 6 Áp dụngs: Low-Frequency RC Oscillator, Crystal-Based Clock Source, Frequency Divider, Periodic Pulse Generator, Asynchronous System Timer, Legacy CMOS Control Logic.
Low-Frequency RC Oscillator
The CD4060BCN suits low-frequency oscillator designs because it combines an internal oscillator section with a 14-stage counter. An external resistor-capacitor network establishes the nominal oscillation frequency, while the divided outputs provide several lower-frequency signals from the same source. Because the device operates from 3.0 V to 15 V and offers 0.45 VDD typical noise immunity, it is useful for legacy CMOS timer and clock circuits. During component selection, account for resistor and capacitor tolerances, parasitic capacitance, temperature drift, and oscillator startup. Select the output stage according to the required frequency and acceptable divider delay rather than assuming every output has identical timing accuracy.
Được đề xuất
Crystal-Based Clock Source
The CD4060BCN can operate as a crystal-based clock generator when the oscillator section is connected to the appropriate crystal and supporting network. The divided counter outputs then supply lower-frequency timing references for digital control, communication, or sequencing systems. Its 3.0 V to 15 V supply range permits operation in conventional CMOS environments, while the 16-lead PDIP package makes the circuit straightforward to prototype and service. Because the counter advances on each negative clock transition, the input clock edge quality directly affects the stability and jitter of divided outputs. Validate crystal startup across temperature and supply voltage, confirm the manufacturer's recommended load capacitance, and check timing margins for the selected divider stage.
Được đề xuất
Frequency Divider
The CD4060BCN provides 14 ripple-carry stages for dividing an input frequency into lower, selectable rates. This makes it useful for clock division, pulse-rate reduction, and periodic event generation in legacy CMOS logic systems. The output taps allow a designer to choose a division factor that fits the required timing without adding a separate counter for every ratio. Since the implementation is ripple carry, later stages accumulate the propagation delay of preceding stages. Use the earliest divider output that meets the frequency requirement, allow sufficient edge settling time, and verify the maximum operating frequency of the selected source when the clock is supplied externally rather than generated internally.
Được đề xuất
Periodic Pulse Generator
A CD4060BCN oscillator can generate a continuous reference that is divided into periodic pulses for timers, indicators, sampling triggers, and basic sequencing systems. The internal oscillator reduces the component count compared with a discrete RC oscillator followed by a separate divider, while the 16-lead PDIP package provides a practical through-hole implementation. The asynchronous reset offers a way to force the counter to a known state when a system event occurs. Design the reset pulse to satisfy the device's logic and timing requirements, avoid retriggering during normal operation, and account for RC tolerances if multiple devices must operate at matching frequencies. Select an output stage based on pulse-width and edge-timing requirements.
Được đề xuất
Asynchronous System Timer
The asynchronous reset of the CD4060BCN is useful in timer and event systems that must return to a known count immediately rather than waiting for a clock edge. A logical 1 at the reset input clears the counter regardless of oscillator state, allowing an external event, supervisor, or controller to establish a defined starting point. The device's 3.0 V to 15 V operating range supports common industrial CMOS control voltages, while typical noise immunity of 0.45 VDD assists with electrically noisy environments. Keep reset traces short, provide a defined inactive level, and ensure that the reset source does not introduce excessive leakage or timing skew. Verify the complete timing budget against the highest counter stage used by the system.
Được đề xuất
Legacy CMOS Control Logic
The CD4060BCN is appropriate for maintenance and modernization of legacy CMOS systems that use 4000-series counter functions around 5 V or 15 V supplies. Its 16-lead PDIP footprint supports through-hole replacement and reduces the effort required to preserve existing board layouts. The 14-stage architecture offers multiple division taps, while the internal oscillator supports standalone timing where an external clock is unnecessary. Before fitting a replacement, compare reset behavior, clock polarity, maximum frequency, output timing, temperature grade, and oscillator recommendations with the incumbent device. For long-term production, qualify the selected source and verify regulatory declarations for the target equipment rather than assuming identical lifecycle or environmental status.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho CD4060BCN — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | CD4060BC | HCF4060BEY | HEF4060BP | CD4060BEX |
|---|---|---|---|---|---|
| Brand | onsemi | onsemi | STMicroelectronics | NXP Semiconductors | Harris |
| Package | 16-lead PDIP | 16-lead PDIP | 16-lead PDIP | 16-lead PDIP | 16-lead PDIP |
| Counter Stages | 14 stages | 14 stages | 14 stages | 14 stages | 14 stages |
| Counter Architecture | Ripple-carry binary counter | Ripple-carry binary counter | Counter/divider | 14-stage counter | Binary counter |
| Oscillator | On-chip RC or crystal oscillator | On-chip RC or crystal oscillator | Oscillator/counter | Oscillator/counter | Oscillator/counter |
| Logic Family | CD4000 CMOS | CD4000 CMOS | 4000 series CMOS | 4000 series CMOS | 4000 series CMOS |
Bảo phân biệt quan trọng
- Direct same-footprint replacement path (vsCD4060BC)
- Higher maximum supply voltage (vsHCF4060BEY)
- Established CD4000-series oscillator and divider architecture (vsHEF4060BP)
Ghi chú thiết kế
Place the decoupling capacitor between pins 16 and 15 with its ground end connected to the nearest solid ground reference. Keep the oscillator timing network at pins 1 and 2 short and away from high-current switching nodes. For a crystal oscillator, route the oscillator path away from digital output and reset traces, and follow the manufacturer's recommended grounding and load-capacitance arrangement. This separation reduces clock jitter, unintended oscillator feedback, and sensitivity to board-level electrical noise.
Use a clean low-jitter external clock when accurate division is required. The CD4060BCN advances on the negative clock transition, so crossing the threshold with excessive noise or slow edges can cause inconsistent counting. Select the earliest divided output that satisfies the required frequency, provide adequate settling time after reset, and verify the timing of the final output stage. This is particularly important for the highest-order outputs because ripple delay accumulates through successive stages.
Do not leave the oscillator, clock, or asynchronous reset inputs floating. The master reset at pin 3 must be returned to a defined inactive level, while oscillator pins 1 and 2 must have a complete timing network. Also confirm that the chosen CD4060BCN source operates at the voltage, temperature, and frequency required by the design. A 16-pin package match alone does not resolve timing-grade or environmental qualification requirements.
Thông tin tuân thủ
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified in the manufacturer information.