CY8C22213-24PI - 8-Bit 24MHz 2KB Flash MCU | Infineon
MPN: CY8C22213-24PI ✗ Cuối đờiCY8C22213-24PI Tóm tắt
A PSoC 1 mixed-signal array is a programmable system-on-chip architecture that integrates a microcontroller core with configurable analog and digital peripheral blocks. In the broader hierarchy, the CY8C22213-24PI belongs to the MCU -> embedded microcontroller -> mixed-signal controller family, combining sequential control with programmable sensor, timing, and interface functions.
The verified product listing identifies the device as an M8C PSoC 1 CY8C22xxx microcontroller with 8-bit processing, a 24 MHz maximum clock, 2 KB Flash organized as 2K x 8, and a 20-DIP package. The -24PI suffix and distributor records identify the commercial ordering configuration used for procurement, while the exact electrical limits and peripheral details require the manufacturer datasheet for design release.
Typical uses include compact industrial control, sensor conditioning, keypad interfaces, simple actuator controllers, and embedded products where a small flash footprint and 20-pin DIP package simplify prototyping or legacy board maintenance. The device's through-hole format is particularly useful when a controller must be inserted or replaced without a fine-pitch surface-mount assembly.
Designers should verify supply voltage, I/O limits, clock configuration, reset behavior, and available peripheral resources against the official datasheet before substitution. The 2 KB Flash capacity also makes firmware sizing and boot behavior important constraints; application code must fit within the available program memory after accounting for required startup and configuration routines.
This page combines verified distributor metadata, package and memory information, application context, and sourcing guidance. It does not infer unreported electrical limits or claim a drop-in replacement unless the manufacturer or distributor data explicitly establishes package and pin compatibility.
Bộ thay thế dễ dàng lắp đặt cho CY8C22213-24PI — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với CY8C22213-24PI (cùng hình factor và footprint) — khác nhau ở Flash Memory, Mounting Type, Package, Product Type.
CY8C22213-24PXI
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
CY8C22213-24PI Tỷ lệ tối đa & tính chất điện
| Product Type | 8-bit mixed-signal microcontroller |
| Architecture | M8C |
| Product Family | PSoC 1 CY8C22xxx |
| Tần số xung maksimum | 24 MHz |
| Flash Memory | 2 KB (2K x 8) |
| Word Width | 8 bit |
| Hộp | 20-DIP (0.300 inch, 7.62 mm) |
| Kiểu lắp đặt | Through-hole DIP |
| Core / Processor | M8C 8-bit core |
| Program Memory Type | Flash |
| Memory Organization | 2K x 8 Flash |
| Manufacturer | Infineon Technologies |
Hướng dẫn cấu hình chân CY8C22213-24PI 20-dip (0.300 inch, 7.62 mm)
Cấu hình chân cho CY8C22213-24PI (20-dip (0.300 inch, 7.62 mm) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho CY8C22213-24PI.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
CY8C22213-24PI phù hợp cho 6 Áp dụngs: Legacy Embedded Control, Compact Sensor Interface, Simple Keypad and Panel Controller, Small Industrial Control Module, Actuator and Relay Interface, Programmable Mixed-Signal Controller.
Legacy Embedded Control
The CY8C22213-24PI is a candidate for maintaining legacy embedded-control boards because the verified data identifies an 8-bit M8C core, 24 MHz maximum clock, 2 KB Flash, and a 20-DIP package. Its through-hole format can simplify replacement on older through-hole products. Before fitting it to a live board, confirm pinout, supply voltage, clock components, reset behavior, and firmware compatibility from the manufacturer datasheet. The 2 KB Flash limit may constrain repairs that add functions or diagnostics.
Được đề xuất
Compact Sensor Interface
The PSoC 1 mixed-signal architecture makes the CY8C22213-24PI a possible fit for compact sensor-interface boards where the verified 8-bit M8C processor and 24 MHz clock provide basic control capability. Firmware can coordinate sensor reads, threshold decisions, and digital outputs, subject to the actual peripheral map and analog specifications in the datasheet. The 20-DIP package supports prototype wiring and through-hole assembly. Flash memory is only 2 KB, so data buffering and code organization must be planned carefully.
Được đề xuất
Simple Keypad and Panel Controller
The CY8C22213-24PI can serve as a small keypad or front-panel controller when the application only needs basic sequencing, debounce logic, status indication, and actuator commands. The verified 24 MHz M8C core provides clock headroom for straightforward control tasks, while the 20-DIP package simplifies point-to-point construction. GPIO availability, electrical limits, and debounce performance must be verified because those values are not present in the supplied search data. Firmware overhead must also fit within the 2 KB Flash budget.
Được đề xuất
Small Industrial Control Module
The CY8C22213-24PI is relevant to small industrial-control modules where a microcontroller, digital I/O, and programmable mixed-signal behavior are needed without a high-performance processor. Its 8-bit architecture and 2 KB Flash are appropriate only for modest control logic; applications requiring extensive logging, networking, or large protocol stacks should use a larger-memory MCU. The 20-DIP package may assist maintenance of older equipment, but industrial temperature, EMC, and lifecycle requirements must be confirmed before deployment.
Được đề xuất
Actuator and Relay Interface
The CY8C22213-24PI can be evaluated for basic actuator, relay, or indicator control when its verified 8-bit processing and 24 MHz clock are sufficient. Firmware can implement state machines, timing, interlocks, and diagnostic outputs, while the through-hole package simplifies wiring in a small controller. The exact I/O current limits, supply voltage, isolation requirements, and drive topology are not supplied and must be taken from the datasheet. Add appropriate transistor, resistor, flyback, and protection components rather than driving loads directly without verification.
Được đề xuất
Programmable Mixed-Signal Controller
The PSoC 1 CY8C22xxx family designation positions the CY8C22213-24PI for programmable mixed-signal control tasks, provided the device's verified datasheet confirms the required analog and digital blocks. The verified 2 KB Flash and 24 MHz maximum clock support a small embedded control program, but they do not by themselves establish the available ADC, DAC, timer, or comparator resources. Engineers should map the application requirements to the exact peripheral configuration and pin assignments. This device is best treated as a compact mixed-signal controller rather than a general-purpose high-memory MCU.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho CY8C22213-24PI — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | CY8C22213-24PXI |
|---|---|---|
| Package | 20-DIP (0.300", 7.62mm) | 20-DIP format identified in comparison search |
| Brand | Infineon Technologies | Cypress Semiconductor family part; current manufacturer naming requires verification |
Bảo phân biệt quan trọng
- Mixed-signal PSoC architecture in a 20-DIP package (vsATMEGA328-AU)
- 24 MHz maximum clock with 8-bit processing (vsATMEGA8A-AUR)
- 2 KB Flash organized as 2K x 8 (vsSTM32F030C6T6TR)
Ghi chú thiết kế
Use the verified 20-DIP format only as a starting point for mechanical planning. Before placing the part, obtain the manufacturer package drawing and confirm pin 1 orientation, notch or dimple location, row spacing, and every signal assignment. Do not copy a pinout from a different CY8C22xxx member because the same family can expose different peripheral mappings.
The supplied records do not state the allowable supply voltage or pin current limits. Before connecting sensors, relays, LEDs, or external logic, verify those limits in the datasheet and include appropriate series resistors, level translation, and protection. Power-supply decoupling must follow the manufacturer application circuit rather than relying only on generic MCU practice.
The 2 KB Flash capacity is a major firmware constraint. Estimate startup, interrupt, driver, protocol, and application code before committing to this MCU; keep a margin for configuration tables and future maintenance. A functionally similar replacement should not be treated as interchangeable merely because its product description uses similar terms, as the verified comparison search explicitly notes possible parameter and circuit-structure differences.
For a mixed-signal implementation, separate sensitive analog routing from switching or high-current digital paths and keep external support components close to their associated pins. The supplied data does not identify the analog block resources, so no specific pin-level routing prescription can be made. Validate the final layout against the manufacturer's reference circuit and measured noise requirements on prototype hardware.
Thông tin tuân thủ
The supplied distributor records do not state RoHS, REACH, lead-free, halogen-free, conflict-mineral, or automotive qualification status. Confirm current declarations from Infineon for the exact ordering code.
