DCR010505U/1K - 1W Isolated DC/DC Converter 5V 200mA | TI
MPN: DCR010505U/1K ✓ Hoạt độngDCR010505U/1K Tóm tắt
An isolated DC/DC converter is a power management module that transfers electrical energy across a galvanic isolation barrier, breaking ground loops and protecting downstream circuitry from upstream voltage transients. Within the power system hierarchy, isolation modules sit between a primary power rail and sensitive analog, communication, or sensor circuitry, combining transformer isolation with on-module regulation - a distinct class from non-isolated buck/boost regulators.
Key features of the DCR01 family include 1000Vrms isolation (1kV operational isolation, 1-second test), a continuous working voltage across the barrier of 60 VDC or 42.5 VAC, and UL1950 component recognition. The module switches at 400 kHz, supports device-to-device synchronization for multi-module systems, and provides thermal protection plus output short-circuit protection. With 53 W/in3 (3.3 W/cm3) power density and a reliability figure of 125 FITS at 55C, the part suits space-constrained isolation designs.
Architecturally, the DCR01 series integrates the power transformer, switching controller, synchronous rectification, and error amplifier into a single molded SOIC package, eliminating the design effort of a discrete isolated flyback supply. Output regulation accuracy is high across line and load, and output ripple noise is very low per the family description.
Typical applications include isolated RS-485/RS-232 transceiver supplies, isolated gate-drive and analog-front-end bias rails in industrial automation, isolated sensor and data-acquisition systems, and ground-loop breaking in medical and test equipment front ends.
A key design consideration: this module is a 5V-in variant, so the primary rail must stay within 4.5V-5.5V; for 12V or 24V rails, use DCR011 or DCR012 family members with the same footprint. Always verify derating versus load and ambient temperature per the datasheet.
This page synthesizes distributor stock status, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Pricing is available on request as of 2026-10-19.
Bộ thay thế dễ dàng lắp đặt cho DCR010505U/1K — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với DCR010505U/1K (cùng hình factor và footprint) — khác nhau ở Input Voltage Range, Isolation Voltage, Package, Protection Features, Reliability.
DCR010503U
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
DCR011505U
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
DCR011503U
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
DCR010505U/1K Tỷ lệ tối đa & tính chất điện
| Cấu trúc | Isolated, regulated DC/DC converter module |
| Số lượng đầu ra | 1 |
| Điện áp đầu ra | 5 V |
| Output Current | 200 mA |
| Output Power | 1 W |
| Phạm vi điện áp đầu vào | 4.5 V to 5.5 V (5 V nominal, +/-10%) |
| Isolation Voltage | 1000 Vrms (1 kV operational, 1-second test) |
| Continuous Barrier Working Voltage | 60 VDC / 42.5 VAC |
| Tần số chuyển đổi | 400 kHz |
| Power Density | 53 W/in3 (3.3 W/cm3) |
| Reliability | 125 FITS at 55 C |
| Protection Features | Thermal shutdown, output short-circuit protection |
| Synchronization | Device-to-device synchronization |
| Safety Recognition | UL1950 recognized component |
| Khoảng nhiệt độ hoạt động | -40 C to +85 C |
| Hộp | SOIC-12 (DVB), surface mount |
Hướng dẫn cấu hình chân DCR010505U/1K soic-12 (dvb), surface mount
Cấu hình chân cho DCR010505U/1K (soic-12 (dvb), surface mount gói). Động cơ điện này có chân cổng, nguồn và đầu ra. Đối với các gói không phân極, tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết hướng dẫn chính xác của chân 1 và chi tiết về vân footprint. Các ứng dụng phổ biến bao gồm thiết kế nguồn cung cấp điện, điều khiển động cơ và chuyển đổi tải.
Không có dữ liệu chân cụ thể sẵn có cho DCR010505U/1K.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
DCR010505U/1K phù hợp cho 6 Áp dụngs: Isolated RS-485 / RS-232 Communication Supplies, Isolated Gate-Drive Bias Rails, Industrial Data Acquisition and Sensor Isolation, Medical and Laboratory Instrument Front Ends, Ground-Loop Breaking in Test and Measurement, 5V-Rail Industrial Embedded Systems.
Isolated RS-485 / RS-232 Communication Supplies
The DCR010505U/1K is a natural fit for powering the isolated side of industrial RS-485 and RS-232 transceivers. Its regulated 5V, 200mA isolated output covers the supply requirement of typical transceiver ICs such as the TI SN65HVD series, while the 1000Vrms isolation barrier breaks the ground loop between remote field nodes and the controller. Very low output noise, a stated feature of the DCR01 family, helps keep receiver threshold margins clean in electrically noisy factory environments. Placed directly adjacent to the transceiver VCC pin with local 10uF and 0.1uF decoupling, the module replaces a discrete flyback converter and its transformer. Device-to-device synchronization prevents beat-frequency interference when multiple isolated channels share one PCB.
Được đề xuất
Isolated Gate-Drive Bias Rails
In motor drives and power converters, low-side and high-side gate drivers each need a clean, isolated bias rail. The DCR010505U/1K supplies a regulated 5V at 200mA across a 1000Vrms barrier, adequate for a single isolated channel of gate-drive logic or an isolated driver front end on the 60 VDC working-voltage barrier. Its 400 kHz switching and internal synchronous regulation deliver stable bias despite bursts of gate-charge load, and integrated short-circuit protection guards against shoot-through faults on the isolated side. Using one module per channel simplifies layout versus a multi-winding bias transformer. Note the working-voltage limit: this module serves functional isolation at up to 60 VDC continuous, not reinforced mains isolation.
Được đề xuất
Industrial Data Acquisition and Sensor Isolation
Analog front ends in PLC analog-input cards and remote I/O benefit from the DCR010505U/1K's isolated, low-noise 5V rail. According to the TI DCR01 family description, the modules combine galvanic isolation with very low output noise and high output accuracy - exactly the combination needed to power isolated ADCs, amplifiers, and 4-20mA transmitter front ends without injecting switching noise into microvolt-level signals. The 200mA output powers a complete isolated front-end channel, and the -40C to +85C operating range covers industrial cabinets. Because the module is regulated, the isolated rail stays accurate as the primary rail varies +/-10%, eliminating post-regulation and reducing BOM count in high-channel-density designs.
Được đề xuất
Medical and Laboratory Instrument Front Ends
Patient-connected and precision laboratory instruments require ground isolation to break leakage-current paths and reject common-mode interference. The DCR010505U/1K's 1000Vrms isolation and UL1950 component recognition provide a compact, pre-certified building block for functional isolation stages in monitoring front ends and bench instrumentation. The 125 FITS reliability figure at 55C supports long-life instrument designs, and the molded 12-pin SOIC keeps the isolated supply smaller than a discrete transformer solution. Its very low output noise, a highlighted DCR01 family feature, preserves signal integrity for biosignal amplifiers. Designers must add any reinforced-isolation barriers required by the applicable medical safety standard at the system level.
Được đề xuất
Ground-Loop Breaking in Test and Measurement
Test equipment, data loggers, and distributed measurement nodes frequently suffer measurement errors from ground potential differences between the acquisition system and the field. Inserting a DCR010505U/1K between the measurement-side supply and the isolated circuitry eliminates the galvanic connection that causes these loops, while its regulated 5V/200mA output runs the isolated electronics directly. The 400 kHz switching frequency keeps the converter's fundamental well above sensitive measurement bands, and synchronization pins allow several modules to lock to a common clock, preventing low-frequency beat products from appearing as measurement artifacts. The compact SOIC-12 (DVB) package fits directly on measurement daughterboards without a custom magnetics design.
Được đề xuất
5V-Rail Industrial Embedded Systems
Embedded controllers, isolated status inputs, and communication mezzanines designed around a 5V industrial backplane can use the DCR010505U/1K without any primary-side regulation, since the module accepts the full 4.5V-5.5V (+/-10%) input range directly. The 1W isolated output powers an isolated microcontroller section, relay-driver logic, or an isolated sensor node, and integrated thermal and short-circuit protection suits unattended industrial operation. The surface-mount SOIC-12 (DVB) package supports standard reflow assembly and a 1000-piece reel format for automated production. For designs migrating to 12V or 24V backplanes, footprint-compatible DCR011 and DCR012 family members allow the same PCB land pattern to be retained.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho DCR010505U/1K — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | DCR010503U | DCR011505U | DCR011503U |
|---|---|---|---|---|
| Package | SOIC-12 (DVB) | SOIC-12 (DVB) - same | SOIC-12 (DVB) - same | SOIC-12 (DVB) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Output Voltage | 5 V | 3.3 V | 5 V | 3.3 V |
| Output Power | 1 W | 1 W | 1 W | 1 W |
| Isolation | 1000 Vrms | 1000 Vrms | 1000 Vrms | 1000 Vrms |
| Switching Frequency | 400 kHz | 400 kHz | 400 kHz | 400 kHz |
| Safety Recognition | UL1950 recognized | UL1950 recognized | UL1950 recognized | UL1950 recognized |
Bảo phân biệt quan trọng
- 5V-input family member - no primary pre-regulation needed (vsDCR011505U)
- 5V output for 5V-native isolated loads (vsDCR010503U)
- UL1950 recognition with defined continuous barrier rating (vsDCR010503U (same feature set))
Ghi chú thiết kế
Place a low-ESR ceramic capacitor (datasheet-recommended value, typically 10uF class) close to the primary-side input pins and local decoupling on the isolated 5V output pin. The 400 kHz switching edges require short, wide traces for the input loop to minimize conducted EMI. Keep the isolation creepage region clear: do not route primary-side traces under the isolated section of the SOIC-12 (DVB) body, and maintain the datasheet's recommended spacing across the barrier on all PCB layers to preserve the 1000Vrms isolation rating.
At the full 1W output load, module internal losses raise the SOIC-12 package temperature; the family is rated -40C to +85C ambient with a thermal-protection trip as a backstop. Estimated: at 85% efficiency (assumed - verify against the datasheet efficiency curve), a 1W load dissipates roughly 0.18W in the module, a modest but non-zero rise in a sealed enclosure. For loads above about 80% of 200mA at elevated ambient, verify the derating curve in the manufacturer datasheet and provide copper area or airflow as indicated.
Three common mistakes with the DCR01 family: (1) applying more than 5.5V input - the DCR010 series is strictly a 5V-input part; use DCR011/DCR012 for 12V/24V rails. (2) Treating the 1000Vrms functional isolation as reinforced mains isolation - the continuous barrier working voltage is only 60 VDC / 42.5 VAC per the datasheet. (3) Ignoring synchronization: when multiple modules run on one board, leave SYNC floating per datasheet guidance or tie them together, since asynchronous modules can generate audible/beat-frequency artifacts.
Thông tin tuân thủ
UL1950 recognized component per TI DCR01 datasheet. RoHS/REACH status not stated in provided data - confirm on the TI product page before ordering.
