DG301ABA - Dual SPST CMOS Analog Switch | Vishay
MPN: DG301ABA ✗ Cuối đờiDG301ABA Tóm tắt
An analog switch is a semiconductor device that uses control logic to connect or disconnect analog signals. The SPST configuration provides one normally open switch path per channel, while the dual-channel package allows two independently controlled routes. In the power-management hierarchy, this component belongs to the interface-IC category because it manages signal connectivity rather than regulating voltage or processing digital data.
The DG301ABA provides break-before-make switching behavior, preventing the input and output terminals from momentarily connecting together during a transition. Its switch-control inputs are compatible with both TTL and CMOS logic. Low charge injection reduces the unwanted voltage transient that can occur when control signals change and is important when switching precision analog signals.
Operation across ±5 V to ±18 V provides flexibility for systems using split analog supplies as well as lower-voltage designs using a single supply. The typical 3.5 mW power consumption supports battery-powered circuitry where switching losses and standby power materially affect energy budget. The control architecture is designed to preserve signal isolation during switching transitions.
Typical uses include battery-powered measurement systems, precision analog signal selection, data-acquisition front ends, test equipment, and general-purpose routing of low-frequency analog signals. The logic-compatible control inputs also make the device convenient for systems where CMOS or TTL digital controllers select among external sensor or conditioning circuits.
Designers should confirm the exact pin configuration and switch state from the manufacturer datasheet before layout. The break-before-make timing must be considered when a downstream circuit cannot tolerate two paths being connected briefly. Input and output signal amplitudes must also remain within the device's absolute maximum and operating limits.
This page combines the DG301ABA architecture, supply-range information, package details, pin-compatible family references, comparison data, and practical routing guidance. It is intended to help engineers evaluate the device for analog switching, select a suitable replacement, and plan PCB implementation without relying on incomplete catalog summaries.
Bộ thay thế dễ dàng lắp đặt cho DG301ABA — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
DG301AAA
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG301ABA/ACA-ABZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG301ABA Tỷ lệ tối đa & tính chất điện
| Switch Configuration | Dual SPST |
| Number of Circuits | 2 circuits |
| Supply Voltage Range, Bipolar | ±5 V to ±18 V |
| Single-Supply Operation | Supported by connecting V− to 0 V |
| Typical Power Consumption | 3.5 mW |
| Control Input Compatibility | TTL and CMOS compatible |
| Switching Action | Break-before-make |
| Charge Injection | Low |
| Hộp | 10-pin TO-100 |
| Kiểu lắp đặt | Through-hole |
Hướng dẫn cấu hình chân DG301ABA 10-pin to-100
Cấu hình chân cho DG301ABA (10-pin to-100 gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho DG301ABA.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
DG301ABA phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Routing, Precision Data-Acquisition Front End, Test and Measurement Signal Routing, Analog Signal Isolation, Audio and Low-Frequency Analog Routing, Industrial Control Signal Multiplexing.
Battery-Powered Sensor Routing
The DG301ABA fits battery-powered sensor interfaces because its dual SPST topology can route a sensor signal between measurement and isolation paths while typical power consumption remains 3.5 mW. Break-before-make operation prevents the old and new signal paths from overlapping during a control transition, while low charge injection limits the control-induced disturbance reaching a sensitive amplifier. The logic-compatible control inputs permit direct connection to CMOS or TTL controller outputs. A single-supply arrangement can also be created by connecting V− to 0 V, although the selected power range and signal amplitudes must be checked against the device ratings before implementation.
Được đề xuất
Precision Data-Acquisition Front End
The DG301ABA is suitable for switching analog inputs in a precision data-acquisition front end, where low charge injection helps preserve measurement integrity during control changes. Its dual SPST organization allows two independent signal paths to be isolated or selected with a small number of control lines. Break-before-make action avoids the unintended interval in which two paths are connected together, which can produce charge sharing or loading errors. The TTL- and CMOS-compatible control inputs simplify integration with digital controllers and analog-to-digital converter interface logic.
Được đề xuất
Test and Measurement Signal Routing
The DG301ABA can route low-frequency measurement signals in test equipment where compact analog switching and controlled transitions are valuable. Its 10-pin TO-100 package provides a straightforward through-hole implementation for laboratory and industrial boards. The break-before-make characteristic helps ensure that the instrument does not momentarily connect a driven node to another source during range or channel changes. Low charge injection reduces the control transient that could otherwise disturb high-impedance measurement nodes. Supply selection should preserve the supported ±5 V to ±18 V operating range, or use the documented single-supply configuration.
Được đề xuất
Analog Signal Isolation
The DG301ABA can implement analog signal isolation between a source and a downstream instrument or amplifier. Opening the switch path reduces coupling between circuit sections, while the break-before-make sequence prevents unintended source overlap during state changes. The dual SPST arrangement provides two controlled isolation points and can simplify layouts where separate analog channels require isolation. Because leakage, off isolation, and on resistance determine practical signal integrity, these parameters should be checked against the source impedance, signal bandwidth, and required isolation margin in the manufacturer data table.
Được đề xuất
Audio and Low-Frequency Analog Routing
The DG301ABA can select low-frequency audio or instrumentation signals when the source impedances remain within the switch’s supported operating conditions. Its break-before-make behavior avoids momentarily cross-connecting two outputs, which is useful when routing mutually exclusive sources. Low charge injection helps limit control transients at the selected output, while TTL- and CMOS-compatible controls permit straightforward interfacing with digital audio or test controllers. The through-hole TO-100 package is particularly convenient for legacy and industrial audio boards that are not built around high-density surface-mount routing.
Được đề xuất
Industrial Control Signal Multiplexing
The DG301ABA can multiplex control or instrumentation signals in an industrial system by placing two SPST switch sections under separate control commands. Its typical 3.5 mW power consumption is advantageous when many switched channels are used in a compact control assembly. The 10-pin TO-100 format supports conventional through-hole board construction and straightforward inspection. For factory equipment, the final component selection should include verification of the operating temperature range, supply limits, on-resistance, leakage, and reliability information rather than relying only on the family description.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho DG301ABA — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | DG301AAA | DG301ABA/ACA-ABZ |
|---|---|---|---|
| Package | TO-100-10 | TO-100-10 | TO-100-10 |
| Brand | Vishay Intertechnology | Vishay Intertechnology | Vishay Intertechnology |
| Supply Voltage Range | ±5 V to ±18 V | ±5 V to ±18 V family range | ±5 V to ±18 V |
| Typical Power Consumption | 3.5 mW | 3.5 mW family value | 3.5 mW |
| Control Input Compatibility | TTL and CMOS compatible | TTL and CMOS compatible family specification | TTL and CMOS compatible |
| Switching Action | Break-before-make | Break-before-make family specification | Break-before-make |
| Charge Injection | Low | Low family characteristic | Low |
| Single-Supply Operation | Supported by connecting V− to 0 V | Supported by family configuration | Supported by connecting V− to 0 V |
Bảo phân biệt quan trọng
- Dual SPST signal routing with controlled transitions (vsDG301AAA)
- Wide bipolar operating range (vsDG301ABA/ACA-ABZ)
- Low switching disturbance for analog routing (vsDG301AAA)
Ghi chú thiết kế
Use the break-before-make transition to keep mutually exclusive signal sources from overlapping during switching. In high-impedance analog nodes, however, the off leakage and charge-injection characteristics remain important. Place the DG301ABA close to the switched node when control-induced charge could be coupled into a sensitive amplifier, and keep the switched traces short and away from high-speed digital or switching-regulator nodes.
For single-supply operation, connect V− to 0 V as directed by the family documentation and select supply and control levels within the stated operating limits. Do not infer the maximum allowable input-signal amplitude from the supply range alone. Check the absolute maximum ratings, on-resistance, leakage, and supply-current conditions before applying signals when the analog input can exceed the selected rail.
The TO-100 package is intended for through-hole assembly, so provide adequate spacing around the body for insertion, soldering, and inspection. Follow the manufacturer land pattern rather than estimating dimensions from the generic package name. Keep the analog switch pins and routed signal traces away from high-current switching paths, and provide a low-impedance ground return to minimize control and charge-injection coupling.
A family-level pin-compatible designation does not automatically prove that every ordering code has identical switch topology or control polarity. Before substituting DG301AAA or another DG301A variant, compare the ordering-code table, pin configuration, logic levels, on-resistance, leakage, bandwidth, operating temperature, and lifecycle status. Pay particular attention to the requirement for break-before-make behavior in the intended application.
Thông tin tuân thủ
Compliance status is not stated in the available manufacturer and distributor information. Verify current declarations for the exact ordering code before production release.