DG411CY+T - Quad SPST Analog Switch | Analog Devices
MPN: DG411CY+T ✓ Hoạt độngDG411CY+T Tóm tắt
An analog switch is an integrated semiconductor that connects or disconnects signal paths under digital control. The DG411 family belongs to the broader switch and multiplexer hierarchy, where multiplexers combine multiple inputs onto an output and demultiplexers distribute one input among several outputs. This particular quad SPST architecture gives each switch an independent path rather than sharing a common internal channel.
Key features include four 1:1 switch channels, 45 ohm nominal on resistance as identified for the DG411CY+T listing, on-resistance matching within 3 ohm maximum between switches, and on-resistance flatness within 4 ohm maximum over the signal range. The family also provides low charge injection, low power consumption, and ESD tolerance of at least 2000 V according to the Analog Devices data sheet.
The DG411CY+T uses independently driven control inputs and is intended for low-voltage signal routing. According to the manufacturer information, the switches conduct equally well in either direction while the device is on. This bidirectional behavior makes the switch suitable for systems where the signal source can move between input and output roles, such as selectable test paths, measurement interfaces, and compact control systems.
Typical uses include sample-and-hold systems, test and measurement equipment, battery-powered instruments, industrial control interfaces, and audio or communication signal routing. Four independently controlled switches can implement four separate point-to-point paths, while the 16-pin SOIC package supports conventional surface-mount assembly and straightforward PCB fanout.
Designers should pay attention to control logic levels, supply voltage, signal amplitude, and switch timing before assigning a signal. Keep routing short, provide a stable ground reference, and avoid exceeding the voltage limits specified for the control inputs and switched terminals. The analog manufacturer data sheet should be used as the authoritative reference for the complete pin assignment and electrical limits.
Bộ thay thế dễ dàng lắp đặt cho DG411CY+T — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với DG411CY+T (cùng hình factor và footprint) — khác nhau ở Number of Switches, Package, Switch Configuration.
DG411DY-E3
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADG411
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG411FEUE+T
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG411DY-E3
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DG411LDY-T1
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG411CY+T Tỷ lệ tối đa & tính chất điện
| Number of Switches | 4 circuits |
| Switch Configuration | 4 x SPST |
| Signal Configuration | 1:1 |
| On Resistance | 45 ohm |
| On-Resistance Matching Between Switches | 3 ohm maximum |
| On-Resistance Flatness Over Signal Range | 4 ohm maximum |
| Supply Voltage Range | 2.7 V to 12 V |
| ESD Tolerance | 2000 V minimum |
| Hộp | 16-pin SOIC |
| Kiểu lắp đặt | Surface Mount |
| Conduction Direction | Bidirectional |
| Control Interface | 4 independent digital control inputs |
Hướng dẫn cấu hình chân DG411CY+T 16-pin soic
Cấu hình chân cho DG411CY+T (16-pin soic gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho DG411CY+T.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
DG411CY+T phù hợp cho 6 Áp dụngs: Test and Measurement Signal Routing, Battery-Powered Instrumentation, Industrial Control Interfaces, Audio Signal Selection, Communication Equipment, Data Acquisition and Sample Paths.
Test and Measurement Signal Routing
The DG411CY+T is well suited to compact test and measurement systems that require several independently controlled analog paths. Each of its 4 SPST channels can connect a source to a measurement instrument without requiring four separate single-switch packages. The 16-SOIC footprint keeps routing compact, while the family’s 3 ohm maximum matching and 4 ohm maximum flatness help maintain similar channel behavior. Because the DG411CY+T is rated at 45 ohm, engineers should include insertion loss, source impedance, and load impedance in the error budget rather than treating it as an ideal closed contact.
Được đề xuất
Battery-Powered Instrumentation
The DG411CY+T can route low-level signals in battery-powered instruments where component count and switching power both matter. Four independently controlled switches are integrated into one 16-pin SOIC package, reducing board space and external control overhead. Its stated 2.7 V to 12 V single-supply range accommodates common portable-system rails. The switch’s low power consumption supports instrumentation designs, while the 45 ohm on resistance must be checked against the source and load impedances to prevent excessive attenuation or measurement error.
Được đề xuất
Industrial Control Interfaces
The DG411CY+T provides a practical way to route control, feedback, or sensor signals in industrial interfaces with multiple branches. Four SPST switches can independently isolate or connect circuits, and the normally closed configuration can support default signal paths when control commands are inactive. Bidirectional conduction allows the same switch arrangement to handle signals traveling in either direction. Industrial implementations should verify logic thresholds, transient levels, operating temperature, and grounding against the manufacturer data sheet before connecting long wiring or noisy equipment to the switched nodes.
Được đề xuất
Audio Signal Selection
The DG411CY+T can implement source selection for low-level audio lines when a resistive signal path is acceptable. Its 4 independently selectable SPST channels support left and right routing, monitoring, mute, or test-point functions in one compact package. The on-resistance matching within 3 ohm maximum and flatness within 4 ohm maximum help preserve channel consistency, although the 45 ohm rating introduces attenuation that depends on the source and load. Confirm the complete audio frequency response and acceptable distortion in the manufacturer data sheet before using the device in precision audio paths.
Được đề xuất
Communication Equipment
The DG411CY+T is useful in communication equipment that needs controlled routing of low-voltage command, monitor, or status signals. The four 1:1 switches provide independent paths for multiplexing functional resources without sharing a common multiplexer channel. Bidirectional operation supports both transmit-monitor and receive-route arrangements. System designers should use the 2.7 V to 12 V operating range as the supply constraint, maintain short high-impedance routing where possible, and confirm that the 45 ohm path resistance is acceptable for the interface being switched.
Được đề xuất
Data Acquisition and Sample Paths
The DG411CY+T can control several acquisition paths when the switched signals are referenced to high source impedances. Its four independent SPST channels make it possible to route a sensor, reference, or test signal under digital supervision. The family’s specified on-resistance matching of 3 ohm maximum and flatness of 4 ohm maximum support consistent behavior across channels. For precision conversion systems, calculate the gain error caused by the 45 ohm switch resistance, use a high-impedance buffer when required, and keep switch transients away from sensitive sampling nodes.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho DG411CY+T — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | DG411DY | ADG411 | DG411FEUE+T | DG411DY-E3 | DG411LDY-T1 |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Vishay Intertechnology |
| Number of Switches | 4 | 4 | 4 | 4 | 4 | 4 |
| Switch Configuration | 4 x SPST | 4 x SPST | 4 x SPST | 4 x SPST | 4 x SPST | 4 x SPST |
Bảo phân biệt quan trọng
- Four independent signal paths in one compact package (vsDG411LDY-T1)
- Lower documented on-resistance for the cross-brand alternative (vsDG411LDY-T1)
- Same-manufacturer family continuity (vsADG411)
- Documented channel consistency (vsDG411DY)
Ghi chú thiết kế
Treat the switch as a 45 ohm series element rather than an ideal connection. For a source resistance Rs and load resistance RL, the inserted path forms a divider with the 45 ohm on resistance. Use the divider ratio to estimate insertion loss, and add the switch resistance to the source impedance when evaluating sensor accuracy. High-impedance buffers can be added when the calculated attenuation exceeds the system error budget.
Route each switched terminal directly to the protected source or destination and keep the loop area small to minimize pickup of switching transients. Place the device ground connection close to the package and provide a low-impedance return path. For long external cables, use protection structures at the connector rather than relying on the switch alone. Confirm the package pin assignment from the Analog Devices DG411 data sheet, Rev. 7, before finalizing artwork.
Do not infer control polarity or normally closed behavior from a generic analog-switch pinout. Verify every control input, supply pin, ground pin, and switched terminal against the exact manufacturer pin table. Also check the maximum terminal voltage, control-input logic levels, and operating temperature. A suffix with the same SOIC-16 outline can still differ in grade, marking, qualification, or ordering conditions.
The device operates from a 2.7 V to 12 V single supply according to the documented DG411 family comparison. Ensure that control levels remain valid at the selected supply voltage and that unused control inputs are tied to a defined state. Decouple the supply close to the device with the capacitance recommended in the manufacturer application guidance, and avoid switching terminal voltages that exceed the absolute maximum ratings.
Thông tin tuân thủ
The DG411CY+T is an industrial and commercial analog switch; no vehicle-specific AEC-Q100 qualification is identified. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer or the relevant declaration.