DG413CY+T - Quad SPST Analog Switch | Analog Devices
MPN: DG413CY+T ✓ Hoạt độngDG413CY+T Tóm tắt
An analog switch is an integrated semiconductor device that connects or disconnects an electrical signal under digital control. The DG413 belongs to the analog switch and multiplexer hierarchy within interface ICs. Its four SPST sections can operate independently, making it suitable for signal-path routing, test systems, measurement circuits, and analog signal-conditioning equipment.
Key features include four switch circuits, 1:1 signal routing, a 45 ohm maximum on-resistance specification, on-resistance matching between switches of 3 ohm maximum, and guaranteed on-resistance flatness of 4 ohm maximum over the signal range. The redesigned switch family also supports bidirectional signal conduction, allowing each switch path to conduct equally well in either direction.
The device operates across positive and negative analog signal ranges identified for the DG413 family. Its low on-resistance matching improves consistency when several switch sections are used in parallel or when signal attenuation must remain predictable across channels. Because it is an analog switch rather than a mechanical relay, the part provides compact, solid-state signal routing and is controlled by digital logic levels.
Typical applications include four-channel analog signal routing, bidirectional test-point multiplexing, sample-and-hold interfaces, instrumentation signal paths, and control systems that require independent normally-open or normally-closed contacts. Each circuit can be controlled separately when the host system requires four distinct routing decisions.
PCB design should preserve the manufacturer's recommended pin arrangement and provide adequate clearance around the 16-pin NSOIC body. Because the switch handles analog signals, trace resistance, connector leakage, off-state behavior, and control-logic timing can influence overall system accuracy. Review the DG413 datasheet pin description and electrical characteristics before finalizing signal paths.
This product page combines manufacturer specifications, package information, verified sourcing references, and practical design guidance. It also identifies the directly comparable 16-SOIC alternatives that can be evaluated when designing a new board or replacing an existing DG413-family device.
Bộ thay thế dễ dàng lắp đặt cho DG413CY+T — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với DG413CY+T (cùng hình factor và footprint) — khác nhau ở Package, Number of Channels, Number of Circuits.
DG413DY+
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DG413DY-E3
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DG413CY+T Tỷ lệ tối đa & tính chất điện
| Number of Circuits | 4 circuits |
| Switch Configuration | 1:1 SPST |
| On-Resistance | 45 ohm maximum |
| On-Resistance Matching | 3 ohm maximum between switches |
| On-Resistance Flatness | 4 ohm maximum over signal range |
| Signal Conduction Direction | Bidirectional |
| Positive Analog Signal Range | 10 V to 30 V |
| Negative Analog Signal Range | -4.5 V to -20 V |
| Hộp | 16-pin NSOIC |
| Số lượng chân | 16 pins |
| Kiểu lắp đặt | Surface mount |
| Temperature Grade | Commercial |
Hướng dẫn cấu hình chân DG413CY+T 16-pin nsoic
Cấu hình chân cho DG413CY+T (16-pin nsoic gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho DG413CY+T.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
DG413CY+T phù hợp cho 6 Áp dụngs: Bidirectional Analog Signal Routing, Automated Test and Measurement Systems, Sample-and-Hold Signal Interfaces, Industrial Control Signal Conditioning, Audio and Communication Path Switching, Portable and Embedded Analog Routing.
Bidirectional Analog Signal Routing
The DG413CY+T fits four-channel bidirectional analog routing because it provides four independent 1:1 SPST circuits that conduct equally well in either direction. Its 45 ohm maximum on-resistance defines the worst-case path resistance, while the 3 ohm maximum matching specification helps maintain consistent behavior between channels. A four-way analog multiplexer, dual-source selector, or programmable signal router can use the switch sections independently. Engineers should calculate the resulting signal attenuation against the source impedance and acquisition circuitry, and confirm control timing from the manufacturer datasheet.
Được đề xuất
Automated Test and Measurement Systems
The DG413CY+T can route a measurement path among multiple analog sources, instrument inputs, or test nodes because its four SPST sections support independent control. The 45 ohm maximum on-resistance and 4 ohm maximum flatness are important when interpreting measured voltage errors and attenuation. For automated test equipment, place the switch close to the DUT or measurement interface to limit additional trace resistance and improve routing repeatability. Validate leakage, switching time, and control levels against the complete Analog Devices DG413 datasheet before defining the test timing budget.
Được đề xuất
Sample-and-Hold Signal Interfaces
The DG413CY+T is appropriate for sample-and-hold front ends that require controlled connections between a sampled signal and one of several circuit nodes. Its four independently operated SPST paths allow a compact implementation of a multi-input or multi-stage analog sampler. The 45 ohm maximum on-resistance should be included in the settling-time calculation, while the 3 ohm maximum channel matching supports predictable comparisons between sampled paths. Use short, low-impedance traces and keep the switched node away from high-impedance leakage-sensitive inputs to preserve measurement accuracy.
Được đề xuất
Industrial Control Signal Conditioning
The DG413CY+T can select and route control or feedback signals in industrial equipment where a compact, electronically controlled analog switch is needed. Its 1:1 SPST configuration supports direct signal-path isolation rather than multiplexer-style sharing of multiple inputs into one output. Four channels allow a controller to manage distinct sensor, actuator, or feedback paths while retaining independent state control. Confirm the control voltage levels, supply requirements, and absolute maximum ratings against the manufacturer datasheet, and ensure the selected signal range remains compatible with both positive and negative operating conditions.
Được đề xuất
Audio and Communication Path Switching
The DG413CY+T can switch low-frequency audio or communication-related analog paths when the design accepts a 45 ohm maximum series resistance. The 3 ohm maximum matching between switches is useful when several channels must have similar insertion loss, and the flatness specification limits resistance variation across the signal range. Four SPST sections make it practical to create source selectors, mute paths, or feedback-routing networks. Avoid using the switch for high-impedance microphone inputs without accounting for its on-resistance, leakage, and any downstream loading.
Được đề xuất
Portable and Embedded Analog Routing
The DG413CY+T supports compact analog routing in portable instruments and embedded controller systems that need four solid-state switch channels. Its 16-pin NSOIC surface-mount package simplifies board integration compared with mechanical relays, while independent control allows unused channels to remain isolated. In a portable design, account for the switch resistance when sizing input and output networks, and keep control traces away from sensitive analog nets to reduce coupling. Confirm operating temperature, supply voltage, and lifecycle requirements in the family documentation before releasing a production design.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho DG413CY+T — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | DG413DY+ | DG413DY-E3 |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Vishay Intertechnology |
| Package | 16-SOIC | 16-SOIC | 16-SOIC |
| Number of Circuits | 4 circuits | 4 circuits | 4 circuits |
| Switch Configuration | 1:1 SPST | 1:1 SPST | 1:1 SPST |
| Maximum On-Resistance | 45 ohm | 45 ohm | 35 ohm |
Bảo phân biệt quan trọng
- Identical four-channel 1:1 SPST architecture (vsDG413DY+)
- Lower published maximum on-resistance (vsDG413DY-E3)
- Defined channel matching and flatness for the Analog Devices family (vsDG413DY-E3)
Ghi chú thiết kế
Include the 45 ohm maximum on-resistance when calculating attenuation and settling behavior. For a source resistance of 1 kohm, the switch resistance contributes approximately 4.3 percent divider loss before connector, trace, and load effects are included. The 3 ohm maximum channel matching can also produce several millivolts of differential error at higher signal levels, so use matched channels for precision comparisons.
Place the DG413CY+T close to the switched node and keep analog traces short to minimize parasitic resistance, capacitance, and injected noise. Route each signal to the correct switch terminal shown in the manufacturer pin-description table, and maintain adequate clearance between the NSOIC body and surrounding copper. Avoid placing high-current or fast-switching traces beneath sensitive analog pins.
Do not substitute a 16-SOIC device solely because its package dimensions look similar. Confirm the terminal-level pin assignment, control polarity, supply range, absolute maximum ratings, leakage, and switching time in the manufacturer datasheet. The DG413DY-E3 has a 35 ohm maximum on-resistance rating, so even though that value is lower than the DG413CY+T rating, other functional limits must still be reviewed before substitution.
Review the control-pin input currents and supply requirements in the Analog Devices DG413 datasheet before adding digital control levels. Series resistors can limit control-pin transients, but their value should be selected after checking the permitted input voltage and current. Ensure that every control signal remains within the device limits during reset, power sequencing, and connector fault conditions.
Thông tin tuân thủ
The DG413CY+T is a commercial-grade analog switch. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the cited product information and therefore remain unknown.