DG444DY+T - 85Ω Quad SPST Analog Switch | Analog Devices
MPN: DG444DY+T ✓ Hoạt độngDG444DY+T Tóm tắt
An analog switch is a semiconductor device that uses control signals to connect or disconnect an analog signal path. A SPST switch provides one conducting path when enabled and an open circuit when disabled. The DG444 belongs to the analog-switch category within interface ICs and semiconductor devices. Four independent SPST switches packaged together allow one control IC to manage multiple test points, sensor inputs, acquisition channels, or signal-isolation paths without requiring four separate switch packages.
The DG444 family provides specified on-resistance matching of 4Ω maximum between switches and guaranteed on-resistance flatness of 9Ω maximum over the signal range. These characteristics reduce channel-to-channel variation and distortion when the same switch IC performs multiple measurements or routes comparable signal amplitudes. The 85Ω on-resistance identifies the part as suitable for many general-purpose analog-routing tasks where low resistance is not the primary requirement.
The monolithic CMOS implementation combines four independent switches in one package. According to the Renesas DG444/DG445 datasheet, the family uses TTL- and CMOS-compatible digital inputs, allowing direct control from common logic families. The Vishay DG444 documentation also identifies a high-voltage silicon-gate process and an epitaxial layer intended to prevent latchup. These characteristics make controlled signal routing possible while improving robustness in systems where static or transient electrical conditions must be considered.
Typical applications include automated test-equipment routing, data-acquisition systems, industrial measurement interfaces, sample-and-hold circuitry, and communication equipment. Quad SPST architecture is especially useful when a system must select between multiple external lines while keeping control logic compact. The 16-pin SOIC package also suits conventional surface-mount PCB assembly and provides adequate pin density for four control inputs and eight signal terminals.
For layout, route each switched signal with a short and continuous trace to minimize parasitic capacitance and resistance. Place input and output decoupling near the associated supply pins, and keep control traces away from sensitive analog nodes to reduce capacitive coupling. Check the control logic levels, allowable analog signal range, and on-state behavior in the manufacturer datasheet before finalizing the schematic or substituting a different switch implementation.
This product page combines the manufacturer family information with distributor package details, pin-compatible replacement analysis, parameter comparisons, and practical PCB guidance. It is designed to help engineers identify the correct switch function, verify footprint compatibility, and plan signal-routing layouts for new or existing circuit-board designs.
Bộ thay thế dễ dàng lắp đặt cho DG444DY+T — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với DG444DY+T (cùng hình factor và footprint) — khác nhau ở Switch Configuration, On-Resistance Flatness Over Signal Range, On-Resistance Matching Between Switches, Package, Latchup Protection.
DG444CY+
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADG444ABRZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG444DY-T1-E3
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG444DY+
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DG444DY-T
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG444DY+T Tỷ lệ tối đa & tính chất điện
| Number of Switches | 4 circuits |
| Switch Configuration | 1:1 |
| Switch Function | SPST |
| On-Resistance | 85Ω |
| On-Resistance Matching Between Switches | 4Ω maximum |
| On-Resistance Flatness Over Signal Range | 9Ω maximum |
| Logic Compatibility | TTL and CMOS compatible |
| Hộp | 16-pin SOIC |
| Số chân | 16 pins |
| Kiểu lắp đặt | Surface-mount |
| Temperature Grade | Industrial |
| Process Technology | High-voltage silicon-gate CMOS |
| Latchup Protection | Epitaxial layer intended to prevent latchup |
Hướng dẫn cấu hình chân DG444DY+T 16-pin soic
Cấu hình chân cho DG444DY+T (16-pin soic gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho DG444DY+T.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
DG444DY+T phù hợp cho 6 Áp dụngs: Automated Test Equipment Signal Routing, Data Acquisition and Measurement Systems, Industrial Sensor Interface, Communication Signal Switching, Sample-and-Hold Signal Control, Portable Measurement Instruments.
Automated Test Equipment Signal Routing
The DG444DY+T is appropriate for automated test-equipment routing because four independent SPST switches can connect several test paths while the system controls each switch separately. Its specified 4Ω maximum on-resistance matching between switches helps maintain consistency across similar channels, while the 9Ω maximum on-resistance flatness limit controls channel variation over the signal range. The 16-pin SOIC package also allows the routing function to fit compactly beside the instrumentation front end. Before implementation, verify leakage, switching time, charge injection, and allowable signal voltage for the test-node voltages used by the equipment.
Được đề xuất
Data Acquisition and Measurement Systems
In a data-acquisition system, the DG444DY+T can route multiple sensor or test signals into a shared measurement channel without requiring a separate physical switch for every line. Four independently controlled SPST paths simplify multiplexing architecture and reduce the number of packages on the PCB. On-resistance matching of 4Ω maximum is useful when channel consistency affects readings, while the 85Ω nominal on-resistance should be included in the input-impedance and settling calculations. The designer should confirm leakage, switching time, input capacitance, and off-state behavior against the selected amplifier and sensor impedance.
Được đề xuất
Industrial Sensor Interface
The DG444DY+T can isolate and route sensor lines in industrial measurement equipment where multiple inputs share a common analog-processing chain. Its four independent SPST channels support per-signal enable control, and the controlled channel matching helps preserve consistent behavior across comparable sensor paths. The 85Ω on-resistance may be acceptable for relatively high-impedance sensors but can create an input-divider error with lower source impedances. Confirm the exact signal range, leakage, supply voltage, and control thresholds in the manufacturer datasheet, especially for long cable runs and exposed industrial interfaces.
Được đề xuất
Communication Signal Switching
The DG444DY+T can be used in communication equipment to switch among external lines, test loops, or alternative termination paths. Four SPST switches in one 16-pin SOIC reduce component count and provide independent control over each route. The family's TTL- and CMOS-compatible inputs simplify connection with control logic, although the valid supply and input levels must be checked for the operating condition. For high-speed signals, the 85Ω on-resistance and package parasitics require signal-integrity analysis; for lower-rate lines, verify switching time and off-state leakage before finalizing the layout.
Được đề xuất
Sample-and-Hold Signal Control
The DG444DY+T is useful in sample-and-hold and capacitor-selection circuits because four SPST switches can connect distinct signals to a common node under independent control. When switching a sampling capacitor, leakage, charge injection, and switch off-state behavior can directly affect accuracy, so those characteristics must be taken from the family datasheet. The 4Ω maximum matching specification helps when several channels are expected to behave similarly. Keep the switched node compact, provide suitable return paths, and avoid routing the high-impedance node next to fast digital control traces.
Được đề xuất
Portable Measurement Instruments
A portable measurement instrument can use the DG444DY+T to route several external inputs while preserving a compact surface-mount layout. The device's four-channel SPST organization replaces four individual switch packages and centralizes control, while the 16-pin SOIC outline is compatible with conventional PCB assembly methods. Because portable instruments may operate from limited supplies and may expose the switch to user-connected sources, verify the exact supply range, analog signal limits, leakage, and control thresholds. Also consider whether the 85Ω on-resistance is low enough for the selected source impedance.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho DG444DY+T — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | DG444CY+ | ADG444ABRZ | DG444DY-T1-E3 | DG444DY | DG444DY-T |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Vishay Intertechnology | Vishay Intertechnology | Renesas Electronics |
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Number of Switches | 4 circuits | 4 channels | 4 channels | 4 circuits | 4 circuits | 4 channels |
| Switch Function | Quad SPST | Quad SPST | Quad SPST | Quad SPST | Quad SPST | Quad SPST |
| Mounting Type | Surface-mount | Surface-mount | Surface-mount | Surface-mount | Surface-mount | Surface-mount |
Bảo phân biệt quan trọng
- Four independently controlled SPST paths in one package (vsADG444ABRZ)
- Specified channel-to-channel on-resistance matching (vsDG444DY-T1-E3)
- Guaranteed on-resistance flatness (vsDG444DY)
Ghi chú thiết kế
Keep each switched analog path short and use a continuous reference plane beneath it. The 85Ω on-resistance is acceptable for many high-impedance sources, but trace resistance and parasitic capacitance can degrade settling and isolation. Route the four control inputs together where practical, keep them away from the sensitive switched node, and place any input or output filtering close to the switch pins.
Do not assume that every quad-switch IC with a 16-pin SOIC is interchangeable. Confirm that the alternative is SPST rather than SPDT, verify active-high or active-low control polarity, and compare the complete pin assignment. A footprint match does not compensate for incorrect switch behavior. Revalidate supply voltage, analog signal limits, leakage, on-resistance, and timing with the original operating conditions.
For sampled or high-frequency signals, account for switch on-resistance, off-state leakage, charge injection, and switching transient rather than relying only on the 85Ω rating. Use the manufacturer timing and capacitance tables to determine whether settling time is acceptable. If the source impedance is low, include the switch resistance in the gain calculation and place a suitable hold capacitor at the sampling node where the circuit architecture permits.
Place the supply bypass capacitor close to the device and provide a low-impedance return path for all switch currents. Check the datasheet's permitted supply range and control-input thresholds against the logic rail used by the system. Because the four switches may turn on simultaneously, confirm that the surrounding circuitry can tolerate the resulting dynamic current without introducing supply disturbance at the switched nodes.
Thông tin tuân thủ
The available product information identifies the industrial temperature grade and a surface-mount 16-pin SOIC package but does not provide explicit compliance declarations for this exact orderable MPN.