DSPIC33EP64GP504T-E/ML - 16-bit 60 MIPs DSC 64KB Flash | Microchip
MPN: DSPIC33EP64GP504T-E/ML ✓ Hoạt độngDSPIC33EP64GP504T-E/ML Tóm tắt
A digital signal controller combines the deterministic control of a microcontroller with the math throughput of a DSP. In the power-management hierarchy, the dsPIC33EP family sits above basic MCUs by adding a DSP engine, high-speed ADC, and motor-control peripherals, making the category the standard choice for embedded control systems that require real-time loop execution such as digital power conversion and precision motor drives.
Key features include the 16-bit dsPIC33E core running at 60 MIPs, on-chip CAN 2.0B communication, three op amps and four comparators for analog signal conditioning, a Charge Time Measurement Unit (CTMU) for touch sensing and time measurement, and a Peripheral Trigger Generator (PTG) for autonomous peripheral sequencing. The device provides 35 I/O pins, five 16-bit timers, four DMA channels, and four external interrupt sources.
Architecturally, the dsPIC33EP core uses a modified Harvard pipeline with a barrel shifter and DSP multiply-accumulate instructions, enabling single-cycle MAC operations critical for control-law computation. The integrated analog front-end reduces external component count in closed-loop power and motor systems, while the E-grade silicon and QFN thermal pad support harsh automotive ambient environments.
Typical applications include automotive body and powertrain auxiliaries, BLDC/PMSM motor control, digital power supplies (PFC, LLC), and industrial sensing nodes that exploit the CTMU and on-chip op amps. The CAN interface makes it a natural fit for in-vehicle networking nodes.
Design consideration: the E suffix denotes the extended -40C to +150C range; the -40C to +85C industrial I-grade alternative costs less if your ambient does not exceed 85C. Route the exposed thermal pad to ground plane for best thermal and noise performance.
This page synthesizes distributor availability, drop-in temperature-grade alternatives, and practical design notes not found in the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho DSPIC33EP64GP504T-E/ML — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với DSPIC33EP64GP504T-E/ML (cùng hình factor và footprint) — khác nhau ở Operating Temperature, Package, Core, Program Memory, RAM.
DSPIC33EP64GP504T-I/ML
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DSPIC33EP64GP504T-H/ML
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DSPIC33EP64GP504-I/ML
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DSPIC33EP64GP504T-E/ML Tỷ lệ tối đa & tính chất điện
| Core | dsPIC33E, 16-bit |
| Core Speed | 60 MIPs (60 MHz clock) |
| Program Memory | 64 KB (22K x 24) FLASH |
| RAM | 8 KB (4K x 16) |
| I/O Pins | 35 |
| Hộp | 44-QFN (8x8 mm), exposed pad, 0.65 mm pitch |
| Nhiệt độ hoạt động | -40C to +150C (E grade) |
| Automotive Qualification | AEC-Q100 qualified |
| Communication Interfaces | CAN 2.0B, UART, SPI, I2C |
| Timers | 5 x 16-bit |
| DMA Channels | 4 |
| External Interrupts | 4 |
| Analog Peripherals | 3 op amps, 4 comparators, CTMU |
| Peripheral Trigger Generator | Yes (PTG) |
| Special Features | Barrel shifter, boundary scan, low-power modes |
| Kiểu lắp đặt | Surface Mount |
| Packaging | Tape and Reel (T suffix) |
Hướng dẫn cấu hình chân DSPIC33EP64GP504T-E/ML 44-qfn (8x8 mm), exposed pad, 0.65 mm pitch
Cấu hình chân cho DSPIC33EP64GP504T-E/ML (44-qfn (8x8 mm), exposed pad, 0.65 mm pitch gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho DSPIC33EP64GP504T-E/ML.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
DSPIC33EP64GP504T-E/ML phù hợp cho 6 Áp dụngs: Automotive Body and Auxiliary Control, BLDC/PMSM Motor Control, Digital Power Supplies (PFC/LLC), Industrial Sensing and Condition Monitoring, Capacitive Touch HMI Panels, Embedded Networked Control Nodes.
Automotive Body and Auxiliary Control
The DSPIC33EP64GP504T-E/ML fits automotive auxiliary nodes because its AEC-Q100 qualification and -40C to +150C E-grade rating survive under-hood and near-engine ambient conditions where standard industrial MCUs fail. The on-chip CAN 2.0B module connects the node directly to the vehicle network without an external CAN controller, while 35 I/O lines drive relays, lamps, and sensors. Three integrated op amps and four comparators condition analog feedback locally, and the CTMU supports capacitive touch interfaces for human-machine controls. Deployed between the vehicle 12V rail (via a regulator) and the actuator drivers, the 60 MIPs core executes control loops and diagnostics deterministically; the trade-off versus a simpler MCU is slightly higher quiescent consumption, acceptable in body modules powered from the main battery.
Được đề xuất
BLDC/PMSM Motor Control
The DSPIC33EP64GP504T-E/ML is a strong fit for Brushless DC and permanent-magnet synchronous motor drives because its dsPIC33E core executes single-cycle DSP multiply-accumulate instructions at 60 MIPs, sufficient for field-oriented control loops at typical 10-20 kHz PWM frequencies. The three on-chip op amps buffer shunt-resistor phase-current signals directly, and four comparators implement hardware overcurrent trip and zero-crossing detection without external analog parts. The Peripheral Trigger Generator sequences ADC sampling to PWM edges autonomously, minimizing loop jitter. Placed between the gate-driver front end and the current-sense shunts, the DSC closes the current and speed loops; the exposed-pad 44-QFN package must be grounded to the power-board ground plane to keep the analog front end quiet relative to switching noise.
Được đề xuất
Digital Power Supplies (PFC/LLC)
In digital power conversion, the DSPIC33EP64GP504T-E/ML supplies the fast, deterministic control needed for PFC and LLC converter loops. The 60 MIPs core with DSP MAC instructions computes compensator updates between PWM cycles, while the PTG and DMA move ADC results into the control loop with minimal CPU overhead, keeping loop latency low and jitter small. Four comparators provide cycle-by-cycle current limiting in hardware, independent of firmware, which is essential for fault survival. The DSC sits between the voltage/current sense dividers and the PWM gate-driver inputs; unlike analog control ICs it allows firmware-defined nonlinear compensation and soft-start profiles, at the cost of requiring careful firmware watchdog design so a code fault cannot leave the power stage uncontrolled.
Được đề xuất
Industrial Sensing and Condition Monitoring
For industrial sensing nodes, the DSPIC33EP64GP504T-E/ML leverages its Charge Time Measurement Unit (CTMU) for precise capacitance and time-interval measurement, enabling level, proximity, and humidity sensing without a dedicated analog front end. Three op amps and four comparators amplify and threshold sensor signals on-chip, and the 12-bit ADC (dsPIC33EP family ADC) samples them under PTG-triggered deterministic timing. SPI and I2C interfaces connect external precision converters or memory, while UART links the node to PLC or SCADA gateways. Operating from a 24V industrial bus through a step-down regulator, the DSC's -40C to +150C rating tolerates panel-mounted environments near heat sources; the trade-off is that on-chip op amps are adequate for conditioning but precision metrology still benefits from an external ADC.
Được đề xuất
Capacitive Touch HMI Panels
The DSPIC33EP64GP504T-E/ML serves touch-based human-machine interfaces because the CTMU peripheral measures charge time on touch pads with resolution fine enough to detect finger capacitance changes, and Microchip provides mTouch sensing libraries for the dsPIC33EP family. With 35 I/O pins, the same DSC drives LEDs, buzzers, and small segment LCD backlights directly, consolidating HMI logic into one chip. The four comparators can implement wake-on-touch thresholds that let the core sleep in low-power mode, cutting average current in battery-adjacent installations. Mounted behind a dielectric overlay, the 44-QFN's exposed pad grounds the analog domain for stable CTMU measurements; keep touch traces short and guard them with ground to prevent false triggers from switching supplies nearby.
Được đề xuất
Embedded Networked Control Nodes
As a general embedded control node, the DSPIC33EP64GP504T-E/ML combines CAN, dual UART, SPI, and I2C on one chip, letting one 60 MIPs core bridge a vehicle or industrial CAN backbone to local sensors and actuators. Four DMA channels offload serial transfers from the CPU, and five 16-bit timers generate the timebases for scheduling, measurement, and pulse-width tasks. The 64KB FLASH accommodates application code plus communication stacks (e.g., CANopen-style layers) without external memory, and the E-grade rating plus AEC-Q100 qualification allows deployment in both industrial and automotive enclosures. Designers should budget the 8KB RAM carefully - large buffers for network stacking are the main constraint - and use the exposed thermal pad tied to ground for EMC robustness on the CAN edge rates.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho DSPIC33EP64GP504T-E/ML — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | DSPIC33EP64GP504T-I/ML | DSPIC33EP64GP504T-H/ML | DSPIC33EP64GP504-I/ML |
|---|---|---|---|---|
| Package | 44-QFN (8x8 mm), 0.65 mm pitch | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Speed | 60 MIPs (60 MHz) | 60 MIPs | 60 MIPs | 60 MIPs |
| Program Memory | 64 KB (22K x 24) FLASH | 64 KB (22K x 24) FLASH | 64 KB (22K x 24) FLASH | 64 KB (22K x 24) FLASH |
| RAM | 8 KB (4K x 16) | 8 KB (4K x 16) | 8 KB (4K x 16) | 8 KB (4K x 16) |
| Operating Temperature | -40C to +150C (E grade) | -40C to +85C (I grade) | -40C to +150C | -40C to +85C (I grade) |
| Packaging Format | Tape and Reel | Tape and Reel | Tape and Reel | Tube |
| I/O Pins | 35 | 35 | 35 | 35 |
Bảo phân biệt quan trọng
- Extended -40C to +150C automotive temperature range (vsDSPIC33EP64GP504T-I/ML)
- Integrated analog front end reduces BOM cost (vsDSPIC33EP64GP504T-I/ML)
- Honest trade-off: 8KB RAM limits buffering (vsDSPIC33EP64GP504T-H/ML)
Ghi chú thiết kế
The E-grade rating extends to +150C ambient, which leaves limited junction-temperature headroom in the 44-QFN 8x8 package. Solder the exposed thermal pad to a minimum 4x4 grid of thermal vias into the ground plane; estimate: at roughly 60-80 mA typical core+I/O supply current from 3.3V, internal dissipation is only ~0.2-0.3 W, but I/O pin drive current (up to 4 mA nominal per pin, more in parallel) adds locally. Verify junction temperature against the datasheet theta-JA with your actual copper area before committing to the +150C corner.
Place a 0.1 uF ceramic decoupling capacitor at each VDD/VDDCORE pin pair within 2 mm of the pin, plus one bulk 10 uF per supply domain. dsPIC33EP devices use an internal core regulator - follow the datasheet-recommended VDDCORE capacitor exactly, as incorrect core decoupling is the most common cause of erratic reset and brown-out behavior on this family. Keep VSS returns from the exposed pad low-impedance.
Do not substitute the /ML footprint part with the /MV (48-pin) variant - it uses a different land pattern and will not mount on a 44-QFN board. Also remember E-grade (to +150C) and I-grade (to +85C) parts are binning variants of the same die: firmware is binary compatible, so a single firmware image can serve both, but never qualify an automotive build on I-grade silicon. Use MPLAB ICD 3/4 or REAL ICE for programming and boundary-scan debug.
For the CAN interface, route CANTX/CANRX as a short pair to the transceiver and keep the CTMU touch/charge-measurement traces away from PWM and CAN lines. The integrated op amps are shared with fixed pins - check the pin-mapping table before allocating analog channels so sensor inputs land on op-amp-capable pins rather than plain ADC pins.
Thông tin tuân thủ
AEC-Q100 qualified and classified Automotive per Microchip USA and DigiKey product data. RoHS/REACH/lead-free status not stated in the provided verified data.
