DSPIC33FJ32GS606T-50I/MR - 16-bit 50 MIPS DSC 32KB | Microchip
MPN: DSPIC33FJ32GS606T-50I/MR ✓ Hoạt độngDSPIC33FJ32GS606T-50I/MR Tóm tắt
A digital signal controller combines the computational throughput of a DSP engine with the control peripherals and ease of use of a microcontroller. Within the power-management hierarchy, a DSC such as the dsPIC33F family member sits above a basic MCU: it executes closed-loop control algorithms for switching power supplies, digital lighting, and motor drives at switching frequencies in the hundreds of kilohertz while retaining general-purpose I/O and communication peripherals.
Key differentiating features include the dedicated SMPS PWM module with high-resolution PWM outputs, a high-speed 12-bit ADC with simultaneous multi-channel sampling, four analog comparators, two quadrature encoder interfaces (QEI), and on-chip DAC channels. These peripherals eliminate external analog control circuitry in switched-mode power conversion designs.
Architecturally, the dsPIC33FJ32GS606 integrates a 16-bit modified Harvard core with DSP multiply-accumulate instructions, operating up to 50 MIPS from an internal PLL. The GS (SMPS) variant of the dsPIC33F family is purpose-built for digital power: its PWM module supports complementary outputs, dead-time insertion, and current-limit trip inputs for cycle-by-cycle current limiting in half-bridge and full-bridge converters.
Typical applications include AC-DC and DC-DC digital power supplies, power factor correction (PFC) stages - Microchip provides an interleaved PFC reference design for this controller - digital ballasts, uninterruptible power supplies, and battery chargers.
Design consideration: the industrial temperature variant (-40C to +85C, suffix I) requires attention to VQFN exposed-pad thermal grounding; the exposed pad must be soldered to a ground plane for both thermal dissipation and signal integrity of the analog peripherals.
This page synthesizes distributor pricing, drop-in family alternatives, and practical design guidance not found in the manufacturer datasheet, with pricing verified against LCSC, DigiKey, and Octopart as of 2026-09-27.
Bộ thay thế dễ dàng lắp đặt cho DSPIC33FJ32GS606T-50I/MR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với DSPIC33FJ32GS606T-50I/MR (cùng hình factor và footprint) — khác nhau ở Package, Operating Temperature, Supply Voltage, Core Architecture, Factory Pack Quantity.
DSPIC33FJ32GS606-50I/MR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DSPIC33FJ64GS606T-50I/MR
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
DSPIC33FJ16GS606T-50I/MR
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
DSPIC33FJ64GS606-I/MR
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →DSPIC33FJ16GS606-I/MR
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
DSPIC33FJ32GS606T-50I/MR Tỷ lệ tối đa & tính chất điện
| Core Architecture | 16-bit dsPIC DSC |
| Max CPU Speed | 50 MIPS |
| Program Memory (Flash) | 32 KB (32K x 8) |
| RAM | 4 KB |
| Điện áp cung cấp | 3.3 V |
| Hộp | 64-VQFN (9x9 mm), exposed pad |
| Nhiệt độ hoạt động | -40C to +85C (Industrial) |
| SMPS PWM Channels | Yes (dedicated SMPS PWM module) |
| Comparators | 4 |
| Quadrature Encoder Interfaces | 2 |
| DAC | Yes (on-chip) |
| Kiểu lắp đặt | Surface Mount |
| Product Series | dsPIC33FJ32GS (SMPS DSC) |
| Product Type | Digital Signal Controller (DSC) |
| Factory Pack Quantity | 40 (Tube) |
| Trạng thái RoHS | Compliant |
Hướng dẫn cấu hình chân DSPIC33FJ32GS606T-50I/MR 64-vqfn (9x9 mm), exposed pad
Cấu hình chân cho DSPIC33FJ32GS606T-50I/MR (64-vqfn (9x9 mm), exposed pad gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho DSPIC33FJ32GS606T-50I/MR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
DSPIC33FJ32GS606T-50I/MR phù hợp cho 6 Áp dụngs: Digital Switch-Mode Power Supplies, Interleaved Power Factor Correction (PFC), Digital Lighting and Ballast Control, Motor Drives and Servo Control, Uninterruptible Power Supplies (UPS), Battery Chargers and DC-DC Converters.
Digital Switch-Mode Power Supplies
The DSPIC33FJ32GS606T-50I/MR is purpose-built for digital SMPS control: its dedicated SMPS PWM module provides complementary outputs with programmable dead-time and high-resolution duty-cycle control, while the high-speed ADC samples output voltage and inductor current synchronously with the PWM period. Running at 50 MIPS, the DSC executes voltage-mode or current-mode control loops with digital compensators at switching frequencies in the 100-500 kHz range. Four on-chip comparators support cycle-by-cycle overcurrent protection with hardware trip inputs, achieving protection latency independent of software. The 32KB Flash accommodates full PFC plus downstream DC-DC control with communication stacks in a single 64-VQFN device, eliminating dedicated analog control ICs.
Được đề xuất
Interleaved Power Factor Correction (PFC)
Microchip provides a dedicated reference design for interleaved PFC built on this SMPS dsPIC DSC family, and the DSPIC33FJ32GS606T-50I/MR fits this role directly. The SMPS PWM module generates multiple phase-shifted PWM channels for interleaved boost stages, while the high-speed ADC samples input current and bus voltage each switching cycle for average-current-mode control. The 50 MIPS DSP core implements harmonic-injection and notch-filter compensators achieving power factors above 0.99. Four comparators provide fast hardware overcurrent trips per phase. The 32KB Flash holds the PFC algorithm plus housekeeping and telemetry code, and the industrial -40C to +85C rating suits server and telecom front-end environments.
Được đề xuất
Digital Lighting and Ballast Control
For digital ballasts and LED drivers, the DSPIC33FJ32GS606T-50I/MR combines the SMPS PWM module's resonant-mode and phase-shift capabilities with the on-chip DAC for programmable reference generation, enabling dimming control without external DACs. The high-speed ADC monitors lamp current and bus voltage at PWM-synchronized intervals, and the four analog comparators implement fast lamp-fault and overcurrent protection in hardware. At 50 MIPS, the controller manages half-bridge or full-bridge resonant topologies common in fluorescent and HID ballasts. The 3.3V supply and 64-pin VQFN allow compact two-layer control boards, while 32KB Flash stores ignition, warm-up, run, and fault state machines with communication interfaces.
Được đề xuất
Motor Drives and Servo Control
The DSPIC33FJ32GS606T-50I/MR includes two quadrature encoder interfaces, making it well suited to servo and BLDC motor control with positional feedback. The SMPS PWM module drives three-phase inverters with complementary outputs and dead-time insertion, while the high-speed ADC performs simultaneous sampling of two phase currents for field-oriented control (FOC) at the 50 MIPS core's full rate. Hardware comparator trips provide shoot-through and overcurrent protection independent of software latency. The 4KB RAM supports FOC state variables, compensation filters, and a communication stack. Industrial temperature rating and 64-pin VQFN with exposed pad enable thermally robust drive boards for factory automation and robotics.
Được đề xuất
Uninterruptible Power Supplies (UPS)
In line-interactive and double-conversion UPS designs, the DSPIC33FJ32GS606T-50I/MR controls the AC-DC rectifier, DC-AC inverter, and battery charger stages with one device. The SMPS PWM module provides the multiple independent PWM channels needed for inverter bridges and buck charger stages, and the high-speed ADC samples AC input, inverter output, and battery current in synchronized slots. Four comparators give hardware-level fault detection for overload and short-circuit events, critical for transfer-time guarantees. The DSP engine executes waveform generation and distortion cancellation at 50 MIPS. The 32KB Flash and 4KB RAM leave headroom for battery-management state machines and PMBus-style host communication.
Được đề xuất
Battery Chargers and DC-DC Converters
The DSPIC33FJ32GS606T-50I/MR implements multi-stage charging algorithms (CC, CV, float, and termination) with full telemetry. The high-resolution SMPS PWM controls buck, boost, or synchronous buck-boost power stages at hundreds of kilohertz, and the high-speed ADC monitors battery voltage and current with PWM-synchronized sampling that avoids switching noise. The on-chip DAC provides programmable current/voltage references, and comparators implement hardware termination and fault cutoffs. At 50 MIPS, the core runs coulomb counting, temperature-compensated charge curves, and CAN or UART communication simultaneously. The 3.3V, 64-VQFN industrial-grade device suits telecom rectifiers, e-bike chargers, and embedded DC-DC bricks.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho DSPIC33FJ32GS606T-50I/MR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | DSPIC33FJ32GS606-50I/MR | DSPIC33FJ64GS606T-50I/MR | DSPIC33FJ16GS606T-50I/MR | DSPIC33FJ64GS606-I/MR | DSPIC33FJ16GS606-I/MR |
|---|---|---|---|---|---|---|
| Package | 64-VQFN (9x9 mm), exposed pad | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| CPU Speed | 50 MIPS | 50 MIPS | 50 MIPS | 50 MIPS | 50 MIPS | 50 MIPS |
| Flash Memory | 32 KB | 32 KB | 64 KB | 16 KB | 64 KB | 16 KB |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Packaging / Delivery | Tape & Reel (T suffix) | Tube (factory pack 40) | Tape & Reel | Tape & Reel | Tube | Tube |
Bảo phân biệt quan trọng
- 32KB Flash balances code space and cost within the GS606 pinout (vsDSPIC33FJ64GS606T-50I/MR)
- Tape & Reel delivery for automated production (vsDSPIC33FJ32GS606-50I/MR)
- More code headroom than the 16GB-tier family member (vsDSPIC33FJ16GS606T-50I/MR)
- Dedicated SMPS PWM peripherals not found on generic dsPIC33F GP parts (vsDSPIC33FJ32GP304-I/ML)
Ghi chú thiết kế
The 64-VQFN (9x9 mm) exposed pad is the primary ground return for the dsPIC33FJ32GS606's high-speed ADC and SMPS PWM module. Solder the exposed pad to a solid ground plane via a 3x3 or larger via array - a solder-mask-defined paste pattern with ~60-70% pad coverage avoids excessive solder squeeze-out. Place 0.1 uF decoupling capacitors within 2-3 mm of each VDD/VSS pin pair, plus one bulk 10 uF ceramic near the supply entry. Analog AVDD should be filtered from DVDD with an ferrite bead or RC network to preserve ADC accuracy in power-conversion designs.
The controller operates from a single 3.3V rail; estimated power dissipation at 50 MIPS with typical activity is on the order of 100-200 mA core+I/O (consult the datasheet electrical characteristics table for exact ICC curves), yielding roughly 0.3-0.7W worst case. The exposed pad with a good ground plane typically keeps junction rise below 20-30C at 85C ambient, but verify with theta-JA from the datasheet package section for your board stack-up. Never float the exposed pad - it is electrically VSS.
In SMPS applications, configure PWM fault/current-limit trip inputs in hardware (comparator-to-PWM direct paths) rather than relying on software interrupts - software latency at 50 MIPS can be too slow for cycle-by-cycle current limiting at 300+ kHz switching frequencies. Also, when migrating from 16KB (GS502/GS504) to this 32KB part or upward to 64KB (GS606 64K variant), verify the linker scripts and programming files target the correct memory map; the family shares peripherals but not identical configuration-word settings across all members.
Keep the SMPS PWM output traces short and route them away from the ADC input pins and the analog ground region. Because the ADC is PWM-synchronized in typical digital-power designs, switching-noise coupling into sample-and-hold circuits appears as sampling artifacts; a dedicated analog ground island connected to the main plane at a single point under the exposed pad, plus RC filtering on current-sense inputs, preserves the 12-bit ADC's effective resolution in half-bridge and full-bridge converters.
Thông tin tuân thủ
RoHS compliance indicated in distributor specification data (DigChip listing). For REACH, lead-free, and conflict-minerals declarations, consult official Microchip environmental compliance documentation for this orderable part number.
