EFM32G230F128-QFN64 - 32MHz ARM Cortex-M3 MCU | Silicon Labs
MPN: EFM32G230F128-QFN64 ✓ Hoạt độngEFM32G230F128-QFN64 Tóm tắt
A microcontroller is a programmable semiconductor that integrates a processor core, memory, digital interfaces, timers, and analog peripherals onto one device. The EFM32G230 belongs to the 32-bit microcontroller hierarchy and combines ARM Cortex-M3 processing with Silicon Labs’ EFM32 energy-management architecture. This combination makes it suitable for portable instruments, industrial sensors, connected equipment, and other embedded-control systems that require compact software support and low standby consumption.
Three principal specifications define this part: a maximum CPU frequency of 32 MHz, 128 kB of embedded Flash, and 16 kB of SRAM. It also provides 56 digital I/O pins and three 16-bit timers. The EFM32G family can consume as little as 0.6 µA in Stop mode and 180 µA/MHz in Run mode, helping designers reduce average system power when the application spends substantial time asleep.
The EFM32 architecture is intended to keep the processor inactive while peripheral functions continue to operate. Its low-energy techniques, fast wake-up behavior, and autonomous peripherals reduce the time and energy required to service common events such as timers, serial communication, and sensor interrupts. The three 16-bit timers support periodic and timing-intensive embedded tasks, while the 56 GPIO pins provide flexibility for switches, indicators, communications, and control signals.
Typical uses include low-power sensor nodes, industrial monitoring modules, compact energy-harvesting equipment, building-control endpoints, portable measurement devices, and connected battery-powered products. The 32 MHz Cortex-M3 core provides sufficient performance for protocol handling, control loops, and moderate real-time processing, while the 128 kB Flash and 16 kB RAM suit firmware with moderate code and working-memory requirements.
PCB planning should account for the 64-QFN footprint, its exposed thermal pad, and the manufacturer’s pin and land-pattern requirements. Decoupling, a stable supply source, exposed-pad thermal coupling, and correct boot configuration are essential for reliable operation. This page combines manufacturer specifications, drop-in options, application guidance, and design-focused comparisons for engineers evaluating the EFM32G230F128-QFN64.
Bộ thay thế dễ dàng lắp đặt cho EFM32G230F128-QFN64 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với EFM32G230F128-QFN64 (cùng hình factor và footprint) — khác nhau ở Digital I/O Pins, Flash Memory, Package, Run Mode Current, Stop Mode Current.
EFM32G230F128G-E-QFN64R
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
EFM32G230F64-QFN64
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EFM32LG230F128G-E-QFN64R
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
EFM32G230F128-QFN64 Tỷ lệ tối đa & tính chất điện
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 128 kB |
| RAM | 16 kB |
| Digital I/O Pins | 56 pins |
| Timer Count | 3 timers |
| Timer Resolution | 16-bit |
| Điện áp cung cấp | 2.5 V or 3.3 V |
| Stop Mode Current | 0.6 µA minimum |
| Run Mode Current | 180 µA/MHz |
| Processor Core | ARM Cortex-M3 |
| Hộp | 64-QFN (9 x 9 mm), exposed pad |
| Kiểu lắp đặt | Surface mount |
| Product Family | EFM32 Gecko |
Hướng dẫn cấu hình chân EFM32G230F128-QFN64 64-qfn (9 x 9 mm), exposed pad
Cấu hình chân cho EFM32G230F128-QFN64 (64-qfn (9 x 9 mm), exposed pad gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho EFM32G230F128-QFN64.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
EFM32G230F128-QFN64 phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Nodes, Industrial Condition Monitoring, Portable Measurement Instruments, Building Automation Endpoints, Connected Control Modules, Energy-Sensitive Embedded Products.
Battery-Powered Sensor Nodes
The EFM32G230F128-QFN64 fits battery-powered sensor nodes because its 32 MHz Cortex-M3 core can process measurements while its low-power modes reduce active-system demand. The EFM32G family consumes as little as 0.6 µA in Stop mode and 180 µA/MHz in Run mode, according to the Silicon Labs data sheet. Three 16-bit timers can schedule periodic sampling, while 56 GPIO pins can support digital sensors and status indicators. The 128 kB Flash also provides room for protocol and application code, although battery-current measurements should include sensor and radio leakage rather than the MCU alone.
Được đề xuất
Industrial Condition Monitoring
The EFM32G230F128-QFN64 is suitable for industrial condition-monitoring modules that combine periodic sensor sampling with local control. Its 56 GPIO pins can accommodate digital sensors, alarm inputs, and status outputs, while three 16-bit timers support sampling intervals and timeout functions. A 32 MHz Cortex-M3 core provides enough performance for signal conditioning, filtering, and communication framing without requiring a higher-power processor. For factory equipment, review the exact operating-temperature and industrial-qualification requirements before deployment, and account for the 64-QFN exposed pad in the enclosure thermal design.
Được đề xuất
Portable Measurement Instruments
The EFM32G230F128-QFN64 fits portable measurement instruments where a 32 MHz processor, 16 kB RAM, and 128 kB Flash must coexist with low standby demand. Its three 16-bit timers can support measurement timing, while the 56 GPIO pins provide flexible control and communication routing. Low-power operation becomes particularly important when the instrument runs intermittently between readings, allowing the processor to sleep while timer and peripheral activity coordinates a rapid wake-up. Firmware should include tested sleep transitions, analog-peripheral settling procedures, and brownout margin checks for the 2.5 V or 3.3 V supply.
Được đề xuất
Building Automation Endpoints
The EFM32G230F128-QFN64 can serve building-automation endpoints that monitor switches, inputs, and networked controls while minimizing standby energy. The 56 digital I/O pins provide ample connections for room sensors, digital contact inputs, and actuator signaling, and the three 16-bit timers help implement periodic update and debounce functions. Its 128 kB Flash supports a substantial embedded firmware image, while the 16 kB RAM supports protocol buffering and working state. Because endpoints may be installed in enclosed wall boxes, include thermal margins for the exposed pad and verify radio coexistence at the complete-system level.
Được đề xuất
Connected Control Modules
The EFM32G230F128-QFN64 is appropriate for compact connected-control modules that pair a low-power MCU with a separate communications device. Its 32 MHz Cortex-M3 core can handle control logic, timers, and protocol tasks, while 128 kB Flash accommodates application and networking code. The 56 GPIO pins support status LEDs, switches, and peripheral control lines around a wireless or wired companion. Fast wake-up and autonomous peripheral operation can reduce the time the processor remains active, although final power performance depends on the communication module’s radio duty cycle and supply current.
Được đề xuất
Energy-Sensitive Embedded Products
The EFM32G230F128-QFN64 fits energy-sensitive products that alternate between active measurement, brief communication, and long idle periods. Its EFM32G architecture provides fast wake-up, autonomous peripheral operation, Stop-mode consumption as low as 0.6 µA, and Run-mode consumption of 180 µA/MHz. The processor can therefore handle a 32 MHz control workload without requiring continuous full-speed operation. Design the system to disable unused peripherals, isolate analog blocks when appropriate, and use the timer and interrupt architecture to wake only the required functions, since peripheral and communication leakage can otherwise dominate total battery consumption.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho EFM32G230F128-QFN64 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | EFM32G230F128G-E-QFN64R | EFM32G230F64-QFN64 | EFM32LG230F128G-E-QFN64R |
|---|---|---|---|---|
| Package | 64-QFN (9 x 9 mm), exposed pad | 64-QFN (9 x 9 mm), exposed pad | 64-QFN (9 x 9 mm), exposed pad | 64-QFN (9 x 9 mm), exposed pad |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Flash Memory | 128 kB | 128 kB | 64 kB | 128 kB naming class |
| Low-Power Features | Stop mode as low as 0.6 µA; fast wake-up; autonomous peripherals | Same EFM32G low-power platform | Same EFM32G low-power platform | Low Energy Gecko family; exact current values require verification |
Bảo phân biệt quan trọng
- Doubles the Flash capacity of the lower-memory Gecko option (vsEFM32G230F64-QFN64)
- Uses a later documented Gecko silicon revision (vsEFM32G230F128-QFN64)
- Preserves substantial code space for connected-control firmware (vsEFM32LG230F128G-E-QFN64R)
Ghi chú thiết kế
Construct the PCB footprint from the Silicon Labs 64-QFN package drawing, including the exposed thermal pad, its thermal-via pattern, and the manufacturer’s solder-mask and paste recommendations. Preserve short return paths for every supply and ground connection, and place input and output decoupling capacitors close to their associated pins. The exposed pad is not automatically interchangeable with a normal QFN lead; its net assignment must follow the pinout and reference design.
Design the 2.5 V or 3.3 V supply with margin for startup current, peripheral load, and transient response. Confirm the selected operating range against the EFM32G data sheet and device errata, and verify brownout behavior in the complete power tree. For battery-powered products, measure the MCU, sensors, and communications hardware separately because the MCU’s 0.6 µA Stop-mode figure does not represent total module consumption.
Use the exposed pad as a deliberate thermal path by adding the manufacturer-recommended copper area and thermal vias. Avoid placing a keepout beneath the pad unless the land pattern explicitly requires it, and route high-current or high-dissipation circuitry away from the MCU’s thermal region. Junction-temperature qualification depends on the actual board area, copper layers, enclosure, ambient temperature, and switching rate of connected peripherals, so calculate the completed assembly rather than relying on package dimensions alone.
Do not confuse the EFM32G230F128G-E-QFN64R revision form with the target ordering code without checking the product-change notice, errata, boot configuration, and production packing method. Also do not assume the EFM32G230F64-QFN64 is functionally interchangeable at the firmware level: its 64 kB Flash is half the target’s 128 kB. Revalidate reset, debug, programming, and peripheral assignments on any substituted device before releasing a production PCB.
Use the low-power architecture deliberately: configure unused peripherals for minimum consumption, select the slowest acceptable clock when performance permits, and wake the processor through timer or peripheral events. The EFM32G family supports 0.6 µA Stop-mode operation and 180 µA/MHz Run-mode operation. Validate duty-cycle behavior with production firmware because debugger settings, uninitialized peripherals, interrupt activity, and inaccurate clock configuration can increase measured consumption.
Thông tin tuân thủ
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was stated in the device pages included for this MPN. Confirm the current declarations for the exact ordering code and package before regulatory submission.