EP2SGX60EF1152I3 - 60K LEs Stratix II GX FPGA, 1152-BGA, Industrial | Intel
MPN: EP2SGX60EF1152I3 ✗ Cuối đờiEP2SGX60EF1152I3 Tóm tắt
A Stratix II GX FPGA belongs to the high-end FPGA family within the programmable logic device (PLD) hierarchy. Stratix II GX -> FPGA -> Programmable Logic Device -> Logic IC -> Integrated Circuit -> Semiconductor. The "GX" suffix denotes integrated multi-gigabit transceivers supporting protocols such as PCIe, Serial RapidIO, XAUI, CEI-6G, and SONET/SDH, eliminating the need for external PHY chips on many line cards. The "EF" infix indicates Enhanced Configuration (EPC) support, enabling fast parallel configuration via external memory devices for sub-100 ms boot.
Key features include 60,440 equivalent logic elements, approximately 2.5 Mbit of embedded memory, dedicated DSP blocks for high-speed multiplication, up to 12 multi-gigabit transceivers (per Stratix II GX family), and PLL-based clock management. The -I3 speed grade and industrial temperature range (-40C to +100C) make this part suitable for harsh-environment deployment in telecom, military, and industrial systems.
The architecture uses 90 nm CMOS process technology with adaptive logic modules (ALMs) that each contain a fracturable 8-input look-up table (LUT), two dedicated adders, and dedicated register chains, enabling higher effective logic density than 4-input LUT architectures. TriMatrix embedded memory blocks (M512, M4K, M-RAM) support single-port, dual-port, and FIFO configurations with byte-enable parity protection.
Typical applications include 10G Ethernet line cards, PCIe Gen1/Gen2 endpoint and root-complex designs, SONET/SDH framer/mapper ASICs, Radar signal processing front-ends, and high-speed serial protocol bridging. The integrated transceivers save bill-of-materials cost and PCB area versus equivalent LUT-fabric-only FPGAs paired with external PHYs.
When designing with this device, ensure proper power-sequencing of the analog transceiver supply (VCCH) versus the digital core supply (VCCINT) to avoid latch-up, and follow the Stratix II GX pin connection guidelines for unused transceiver pins. PCB layout requires impedance-controlled 100-ohm differential traces for the high-speed serial links, and a minimum 4-layer stackup with continuous ground planes is recommended.
This page synthesizes distributor pricing, drop-in same-package alternatives from the Site MPN list, and practical design notes that complement the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho EP2SGX60EF1152I3 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với EP2SGX60EF1152I3 (cùng hình factor và footprint) — khác nhau ở Package, Mounting Type, Operating Temperature, Series, Speed Grade.
EP2SGX60EF1152I3N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EP2SGX60EF1152I4N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EP2SGX60EF1152C5N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EP2SGX60EF1152C4N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EP2SGX60EF1152C3N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EP2SGX60EF1152I3 Tỷ lệ tối đa & tính chất điện
| Family | Stratix II GX |
| Series | EP2SGX60 |
| Logic Elements (LEs) | 60,440 |
| Adaptive Logic Modules (ALMs) | 30,220 (estimated from LEs) |
| Equivalent Logic Cells (CLBs) | 60,440 |
| Embedded Memory (Bits) | 2,544,192 bits (per DigiKey listing for the I4N variant) |
| Maximum Internal Frequency | 717 MHz |
| Combinational Delay (per CLB) | 2.99 ns |
| Maximum Transceiver Data Rate | 6.375 Gbps (per Stratix II GX family spec) |
| Total RAM Bits | 2,544,192 bits |
| Hộp | 1152-ball FBGA, 35 mm x 35 mm, 1 mm pitch |
| Pin/Ball Count | 1152 |
| Kiểu lắp đặt | Surface Mount (BGA) |
| Nhiệt độ hoạt động | -40C to +100C (Industrial, I3 speed grade) |
| Speed Grade | I3 (Industrial) |
| Configuration Mode | Enhanced (EPC) - fast parallel via external memory |
| Process Technology | 90 nm CMOS |
Hướng dẫn cấu hình chân EP2SGX60EF1152I3 1152-ball fbga, 35 mm x 35 mm, 1 mm pitch
Cấu hình chân cho EP2SGX60EF1152I3 (1152-ball fbga, 35 mm x 35 mm, 1 mm pitch gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho EP2SGX60EF1152I3.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
EP2SGX60EF1152I3 phù hợp cho 6 Áp dụngs: 10 Gigabit Ethernet Line Card, PCI Express Endpoint and Root Complex, SONET/SDH Framer and Mapper, Radar Signal Processing Front-End, High-Speed Protocol Bridge (Serial RapidIO / XAUI / CEI-6G), Industrial Test and Measurement Instrumentation.
10 Gigabit Ethernet Line Card
The EP2SGX60EF1152I3 is well suited to 10 Gigabit Ethernet line cards because its integrated multi-gigabit transceivers support both XAUI (4 x 3.125 Gbps) and 10GBASE-R (10.3125 Gbps) directly, eliminating external PHY chips. The 60,440 logic elements comfortably host a 10G MAC, PCS layer, rate-matching FIFO, and management interfaces, while the embedded TriMatrix memory blocks (2.5 Mbit) provide low-latency packet buffering. Compared to using a Stratix II (non-GX) plus an external PHY, the GX integration saves PCB area and reduces bill-of-materials cost.
Được đề xuất
PCI Express Endpoint and Root Complex
The EP2SGX60EF1152I3 implements PCIe Gen1 (2.5 Gbps) and Gen2 (5.0 Gbps) endpoint and root-complex designs using its hard PCIe intellectual property blocks and integrated transceivers. The device meets the 250 ns maximum latency requirement for Gen1 with deterministic latency through dedicated clock-data-recovery circuits. Per the Stratix II GX PCIe user guide, the IP core supports x1, x4, and x8 link widths and includes configuration space registers, DMA engines, and MSI/MSI-X interrupt handling, ideal for add-in cards and embedded compute modules.
Được đề xuất
SONET/SDH Framer and Mapper
The EP2SGX60EF1152I3 supports SONET OC-48/STM-16 (2.488 Gbps) and OC-192/STM-64 (9.953 Gbps) framer/mapper implementations through its multi-gigabit transceivers and high logic capacity. The DSP blocks accelerate Reed-Solomon forward error correction, while the dedicated serializer/deserializer (SERDES) interfaces maintain the strict jitter budgets required by Telcordia GR-253. Telecom OEMs historically chose this device for legacy transport equipment, and the industrial temperature grade ensures deployment in central office environments.
Được đề xuất
Radar Signal Processing Front-End
The EP2SGX60EF1152I3 serves as a digital front-end in radar signal processing chains, where its transceivers digitize IF signals at gigasample-per-second rates and the logic fabric performs pulse compression, MTI filtering, and CFAR detection. The 60K logic elements enable real-time processing of multiple receiver channels simultaneously, and the embedded memory supports coefficient storage for matched filters. Industrial temperature rating is essential for ground-based and shipboard radar installations in harsh environments.
Được đề xuất
High-Speed Protocol Bridge (Serial RapidIO / XAUI / CEI-6G)
The EP2SGX60EF1152I3 bridges between high-speed serial protocols in heterogeneous backplanes - for example, converting Serial RapidIO to XAUI between a DSP cluster and an Ethernet switch fabric. The transceivers operate up to 6.375 Gbps, covering Serial RapidIO, XAUI, CEI-6G, and proprietary backplane links. The device's logic capacity supports multiple bridge cores in parallel with throughput monitoring and statistics counters, while the configuration memory retains bitstream integrity across power cycles in mission-critical deployments.
Được đề xuất
Industrial Test and Measurement Instrumentation
The EP2SGX60EF1152I3 integrates the FPGA logic and high-speed transceivers needed for digital oscilloscopes, logic analyzers, and protocol analyzers operating in industrial settings. The transceivers capture data from DUTs at multi-gigabit rates, and the logic fabric performs real-time decoding, triggering, and display rendering. Industrial temperature grade (-40C to +100C) allows deployment in factory-floor test racks, while the EPC enhanced configuration enables fast boot under 100 ms - critical for production-line test systems that cycle power frequently.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho EP2SGX60EF1152I3 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | EP2SGX60EF1152I3N | EP2SGX60EF1152I4N | EP2SGX60EF1152C5N | EP2SGX60EF1152C4N | EP2SGX60EF1152C3N |
|---|---|---|---|---|---|---|
| Package | 1152-ball FBGA (35x35 mm, 1.0 mm pitch) | 1152-ball FBGA - same | 1152-ball FBGA - same | 1152-ball FBGA - same | 1152-ball FBGA - same | 1152-ball FBGA - same |
| Brand | Intel (formerly Altera) | Intel | Intel | Intel | Intel | Intel |
| Logic Elements | 60,440 | 60,440 | 60,440 | 60,440 | 60,440 | 60,440 |
| Temperature Grade | Industrial (-40C to +100C) | Industrial | Industrial | Commercial (0C to +85C) | Commercial | Commercial |
| Speed Grade | I3 (mid-speed) | I3 | I4 (faster) | C5 (fastest) | C4 | C3 |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
| Configuration Mode | Enhanced (EPC) | Enhanced (EPC) | Enhanced (EPC) | Enhanced (EPC) | Enhanced (EPC) | Enhanced (EPC) |
Bảo phân biệt quan trọng
- Same-die, lead-free terminal finish variant (vsEP2SGX60EF1152I3N)
- Higher speed grade for tighter timing margins (vsEP2SGX60EF1152I4N)
- Commercial temperature variant for cost-sensitive applications (vsEP2SGX60EF1152C5N)
Ghi chú thiết kế
The EP2SGX60EF1152I3 requires multiple power rails: VCCINT (core), VCCIO (I/O banks), VCCA_PLL (PLL analog), VCCH_GXB (transceiver analog), and VCCR_GXB/V CCT_GXB (transceiver analog). Power-on sequencing must follow Intel's Stratix II GX Power-on Reset Requirements, with VCCINT reaching 90% of nominal before VCCIO and VCCH_GXB. Failure to sequence correctly may cause latch-up or long-term reliability degradation. Use a multi-rail power management IC (PMIC) such as the LTC3566 or LTM4677 to enforce sequencing.
Estimated: at maximum junction temperature 100C (industrial limit) and theta_JA of approximately 8 C/W (with thermal pad and 200 LFM airflow), the device can dissipate up to 11.5 W. Without airflow, theta_JA rises to roughly 14 C/W, limiting dissipation to about 7 W. The 1152-ball FBGA package requires thermal vias in a 1.2 mm pitch grid beneath the package thermal pad, with at least 25 vias connecting to an internal ground plane for adequate heat removal.
High-speed transceiver channels require 100-ohm differential impedance-controlled traces with length matching to within 5 mils intra-pair and 50 mils inter-pair for data rates above 5 Gbps. Use a 6-layer or 8-layer PCB stackup with stripline routing between continuous ground planes. AC-coupling capacitors (100 nF) must be placed close to the receiver pins; do not route DC-coupled. For PCIe Gen2 interfaces, follow the Intel PCIe Reference Design checklist for via stub minimization.
Stratix II GX transceivers use CML (Current-Mode Logic) signaling with internal termination that defaults to enabled. Always enable internal termination in the Quartus II assignment editor to avoid signal reflections. Use IBIS-AMI models (available from Intel) for channel simulation; the Stratix II GX receiver requires a minimum eye-opening of 100 mV at the input pin for reliable operation at 6.375 Gbps.
Do not leave transceiver channels floating when unused; tie each unused TX output through the recommended AC-coupling capacitor to ground, and disable the corresponding PLL and channel in the Quartus II device configuration. Failure to do so increases power consumption by approximately 100 mW per channel and may cause inadvertent emissions. Also, ensure the JTAG chain is correctly terminated with a 4.7 kohm pull-up on TCK and pull-down on TMS per IEEE 1149.1 specifications.
Thông tin tuân thủ
RoHS and lead-free status for the base EP2SGX60EF1152I3 (without N suffix) is recorded as [DATA_NEEDED] because the retrieved snippets do not explicitly state compliance. The N-suffix variants (e.g. EP2SGX60EF1152I3N) are lead-free per Altera ordering information. AEC-Q100 not applicable for FPGAs. Customers should verify RoHS compliance with their distributor for new orders.
