EPM7160SQC160-10N - 160 Macrocells MAX 7000S CPLD, 10ns, PQFP-160
MPN: EPM7160SQC160-10N ✗ Cuối đờiEPM7160SQC160-10N Tóm tắt
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that combines multiple PAL-like macrocell arrays on a single chip with a programmable interconnect matrix. Positioned in the taxonomy as programmable logic -> PLD -> CPLD -> MAX 7000S family, the EPM7160SQC160-10N sits between simple PAL/GAL devices and larger FPGAs, offering instant-on EEPROM technology, deterministic timing, and 5V tolerant I/O. The MAX 7000S series uses Altera's second-generation MAX architecture with the Classic IEEE Std 1149.1 JTAG interface for in-system programming (ISP).
Key features include 3,200 usable gates, 160 macrocells, 10 ns tPD (pin-to-pin delay), 167 MHz maximum internal frequency, 5.0V VCCINT, in-system programmability via JTAG, and open-drain / programmable I/O standards. The architecture provides four dedicated inputs per macrocell, a global clock network, and a programmable power-saving mode that reduces standby current by up to 50 percent when the device is idle.
Typical applications include bus decoding and address mapping in 5V legacy systems, glue-logic replacement for multiple discrete TTL/CMOS gates, peripheral controllers (UART, FIFO, DMA), state machines for motor control front-ends, and I/O expansion in 8051/MCS-51 embedded designs. The 160-pin PQFP package provides ample I/O for wide data buses and parallel interfaces.
This page synthesizes distributor pricing (as of 2026-09-13), drop-in MAX 7000S alternatives, and practical design notes for the EPM7160SQC160-10N that are not aggregated on any single manufacturer or distributor page.
Bộ thay thế dễ dàng lắp đặt cho EPM7160SQC160-10N — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với EPM7160SQC160-10N (cùng hình factor và footprint) — khác nhau ở Operating Temperature, Package, Family, Supply Voltage (VCCINT), Usable Gates.
EPM7160SQC160-10
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPM7160EQC160-15
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
EPM7160EQC160-12
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →EPM7160EQC160-20
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
EPM7160SQC160-15
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
EPM7160SQC160-10N Tỷ lệ tối đa & tính chất điện
| Family | MAX 7000S |
| Macro Cells | 160 |
| Usable Gates | 3,200 |
| Logic Elements / Blocks | 10 Logic Array Blocks (LABs) |
| User I/O Pins | 104 |
| Pin-to-Pin Delay (tPD) | 10 ns |
| Maximum Internal Frequency | 167 MHz |
| Counter Speed (fCNT) | 100 MHz |
| Supply Voltage (VCCINT) | 5.0 V |
| In-System Programmability | Yes (JTAG IEEE 1149.1) |
| Nhiệt độ hoạt động | 0 C to 70 C (Commercial) |
| Hộp | PQFP-160 (SQC) 31.2 x 31.2 mm |
| Kiểu lắp đặt | Surface Mount |
| Trạng thái RoHS | Non-Compliant (Pb-bearing PQFP) |
| Memory Technology | EEPROM |
Hướng dẫn cấu hình chân EPM7160SQC160-10N pqfp-160 (sqc) 31.2 x 31.2 mm
Cấu hình chân cho EPM7160SQC160-10N (pqfp-160 (sqc) 31.2 x 31.2 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho EPM7160SQC160-10N.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
EPM7160SQC160-10N phù hợp cho 6 Áp dụngs: 5V Legacy Bus Decoder and Address Mapping, Glue Logic Replacement for Discrete TTL/CMOS Gates, Peripheral Controllers (UART, FIFO, DMA), Industrial State Machines for Motor-Control Front-Ends, I/O Expansion for 8051/MCS-51 Embedded Designs, Custom Bus Arbiters and Interrupt Controllers.
5V Legacy Bus Decoder and Address Mapping
The EPM7160SQC160-10N fits 5V legacy bus-decoding applications because its 5.0V VCCINT and 5V-tolerant I/O eliminate the need for level shifters when interfacing with classic TTL peripherals, microcontrollers, and memory buses. Its 160 macrocells and 104 user I/O pins provide ample logic capacity to decode 24-bit or wider address ranges, generate chip-select signals for multiple peripherals, and implement wait-state insertion logic in a single device. The 10 ns tPD ensures that address-to-CS propagation remains well within ISA bus timing margins.
Được đề xuất
Glue Logic Replacement for Discrete TTL/CMOS Gates
The EPM7160SQC160-10N replaces multiple discrete 74-series TTL and CMOS logic packages in retro-computing and industrial-control applications. With 160 macrocells, designers can integrate 10-20 standard logic functions (multiplexers, latches, encoders, parity generators) into one CPLD, reducing PCB area, BOM cost, and assembly complexity. The 5V supply and PQFP-160 surface-mount package suit retro ISA-bus and VMEbus boards where 5V tolerance is mandatory and leaded PQFPs survive hand-solder rework.
Được đề xuất
Peripheral Controllers (UART, FIFO, DMA)
The EPM7160SQC160-10N suits peripheral-controller implementations such as custom UARTs, FIFO buffers, and DMA engines in embedded motherboards and test instruments. Its 167 MHz internal counter frequency and 10 ns combinatorial delay allow 100 MHz+ serial-baud generation and reliable state-machine sequencing for high-throughput DMA. The 104 user I/O pins accommodate 8/16-bit parallel FIFOs plus handshake/status flags, while JTAG ISP supports in-field firmware updates for production diagnostic boards.
Được đề xuất
Industrial State Machines for Motor-Control Front-Ends
The EPM7160SQC160-10N serves industrial state-machine front-ends for stepper and BLDC motor-control boards where deterministic logic timing is required. Its EEPROM-based non-volatile configuration eliminates external boot memory and supports instant-on operation within 200 ms of power-up. The commercial 0 C to 70 C temperature range covers most factory-floor enclosures, and 5V I/O directly drives opto-isolated gate drivers and encoder inputs without additional buffering.
Được đề xuất
I/O Expansion for 8051/MCS-51 Embedded Designs
The EPM7160SQC160-10N expands I/O in 8051/MCS-51-based embedded designs by providing 104 5V-tolerant user I/O pins accessible via memory-mapped registers. The CPLD decodes upper address lines and converts slow 8051 port operations into parallel multi-bit I/O cycles. With 10 ns tPD, address-to-output latency fits within standard 8051 MOVX timing without wait-state insertion. This pattern is common in legacy industrial controllers, security panels, and point-of-sale terminals still in production.
Được đề xuất
Custom Bus Arbiters and Interrupt Controllers
The EPM7160SQC160-10N implements custom multi-master bus arbiters and interrupt controllers in VMEbus, Multibus, and proprietary backplane designs. With 160 macrocells, designers can encode priority logic, daisy-chain arbiters, and vectored interrupt tables in one device. The 5V supply matches legacy backplane signaling, and JTAG ISP allows late-stage priority-table updates during integration. The PQFP-160 package provides enough I/O for 32-bit data plus 16-bit arbitration/control signals with margin.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho EPM7160SQC160-10N — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | EPM7160SQC160-10 | EPM7160EQC160-15 | EPM7160EQC160-12 | EPM7160EQC160-20 | EPM7160SQC160-15 |
|---|---|---|---|---|---|---|
| Package | PQFP-160 (SQC) | PQFP-160 (SQC) - same | PQFP-160 (SQC) - same | PQFP-160 (SQC) - same | PQFP-160 (SQC) - same | PQFP-160 (SQC) - same |
| Brand | Intel (formerly Altera) | Intel - same | Intel - same | Intel - same | Intel - same | Intel - same |
| Family | MAX 7000S | MAX 7000S - same | MAX 7000E | MAX 7000E | MAX 7000E | MAX 7000S - same |
| Macro Cells | 160 | 160 | 160 | 160 | 160 | 160 |
| Pin-to-Pin Delay (tPD) | 10 ns | 10 ns | 15 ns | 12 ns | 20 ns | 15 ns |
| Usable Gates | 3,200 | 3,200 | 3,200 | 3,200 | 3,200 | 3,200 |
| User I/O | 104 | 104 | 104 | 104 | 104 | 104 |
| Supply Voltage | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V |
| Lifecycle Status | NRND | NRND | NRND | NRND | NRND | NRND |
Bảo phân biệt quan trọng
- Pin-to-pin timing 33% faster than -15 grade siblings (vsEPM7160SQC160-15)
- MAX 7000S in-system programmability via JTAG (vsEPM7160EQC160-15 (MAX 7000E))
- Largest I/O count in EPM7160 PQFP-160 family (vsEPM7128SQC160-10N)
Ghi chú thiết kế
The EPM7160SQC160-10N requires a single 5.0V supply (VCCINT) with recommended tolerance of +/- 5% per the MAX 7000S datasheet. Decouple each VCC/VCCIO pair with a 0.1 uF ceramic capacitor placed within 5 mm of the package pin, plus a 10 uF tantalum bulk capacitor near the supply entry point. The device draws approximately 100-300 mA depending on logic utilization and toggle rate; provision for a 500 mA supply is recommended to handle in-rush during ISP programming.
Estimated: at 50% macrocell utilization, 100 MHz toggle rate, and 5V supply, the EPM7160SQC160-10N dissipates approximately 0.5-1.0 W. The PQFP-160 package has theta_JA of approximately 40 C/W (typical for leaded PQFP), giving a junction temperature rise of 20-40 C above ambient. Commercial temperature range (0 C to 70 C) is satisfied in standard office and industrial environments without active cooling. For enclosed chassis, verify theta_JC and derate if ambient exceeds 50 C.
Route JTAG signals (TDI, TDO, TMS, TCK) with short traces (< 50 mm) and avoid parallel routing with high-speed switching signals to prevent programming errors. The PQFP-160 package requires a 31.2 x 31.2 mm footprint with 0.65 mm pitch gull-wing leads; use a PCB land pattern compliant with IPC-7351 nominal-density standards. Reserve a 4-pin header for the JTAG download cable (ByteBlasterMV or USB-Blaster) accessible from the board edge.
Do not confuse the EPM7160SQC160-10N (PQFP-160, 160 macrocells) with the EPM7160SLC84-10 (PLCC-84, 64 macrocells) - these are NOT pin-compatible despite sharing the EPM7160 prefix. Always verify the package suffix (SQC = PQFP-160, SLC = PLCC-84, ELC = PLCC-84, SLI = PLCC-84 industrial) before PCB layout. Also note that MAX 7000S is 5V-only and is not compatible with 3.3V MAX II designs without a level-shifting interface.
Thông tin tuân thủ
PQFP-160 package contains lead-bearing solder finish (non-RoHS). Reach SVHC compliance per Intel material declarations. AEC-Q100 not applicable - this is a commercial-grade CPLD. Choose MAX II EPM570 for new RoHS-compliant designs.
