ICL7652CPD+ - 450kHz Zero-Drift Op Amp | Maxim Integrated
MPN: ICL7652CPD+ ✗ Cuối đờiICL7652CPD+ Tóm tắt
A zero-drift operational amplifier is an amplifier that uses continuous-time chopping and internal nulling techniques to suppress low-frequency input-offset drift. This category belongs to the broader precision-amplifier and signal-conditioning hierarchy. Chopper-stabilized amplifiers are especially useful when a circuit must amplify small differential signals without converting slow temperature changes, resistor drift, or amplifier drift into a significant output error.
The ICL7652CPD+ provides a 450 kHz gain-bandwidth product and 0.5 V/us slew rate. These figures place it among amplifier types suitable for low-frequency precision signal chains with moderate bandwidth requirements. Its 15 pA input bias current minimizes disturbance from high-impedance sources, while the listed 700 uV input offset defines the baseline static error that must be considered in precision gain stages.
The ICL7652CPD+ uses a chopper-stabilized architecture to reduce offset drift and 1/f noise. A chopper amplifier periodically reverses the input polarity and demodulates the result, allowing very small internal offsets to be cancelled. Practical implementations still require attention to input filtering, output-noise bandwidth, clock-related artifacts, and the stability of the surrounding feedback network.
Typical uses include low-level sensor conditioning, strain-gauge and bridge-amplifier front ends, precision current measurement, low-frequency active filters, laboratory instrumentation, and data-acquisition channels. The 15 pA bias current is particularly useful when the source impedance is high, while the 450 kHz bandwidth provides enough loop gain for several common precision-amplifier topologies.
Because the ICL7652CPD+ is obsolete, engineers should assess whether an existing design can remain on this part, whether an order-on-request supply route is acceptable, and whether a qualified drop-in alternative can be validated. For new precision designs, compare offset voltage, bias current, bandwidth, slew rate, supply range, package pinout, noise behavior, and lifecycle status rather than relying only on the zero-drift label.
This page combines the listed electrical characteristics, package information, lifecycle status, drop-in candidates, and application-specific design guidance. It also identifies unspecified parameters explicitly so engineers can check the manufacturer datasheet before release and avoid basing production decisions on incomplete assumptions.
Bộ thay thế dễ dàng lắp đặt cho ICL7652CPD+ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
ICL7652CPD
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ICL7652CPD-2
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ICL7652CTV
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ICL7652CPD+ Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Zero-Drift Operational Amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 450 kHz |
| Slew Rate | 0.5 V/us |
| Input Bias Current | 15 pA |
| Input Offset Voltage | 700 uV |
| Hộp | 14-PDIP, 0.300 inch (7.62 mm) row spacing |
| Số lượng chân | 14 pins |
| Kiểu lắp đặt | Through-hole |
| Product Status | Obsolete |
Hướng dẫn cấu hình chân ICL7652CPD+ 14-pdip, 0.300 inch (7.62 mm) row spacing
Cấu hình chân cho ICL7652CPD+ (14-pdip, 0.300 inch (7.62 mm) row spacing gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho ICL7652CPD+.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ICL7652CPD+ phù hợp cho 6 Áp dụngs: Precision Bridge Sensor Front Ends, Low-Level Current Measurement, High-Impedance Sensor Signal Conditioning, Data Acquisition Signal Chains, Precision Instrumentation Amplifiers, Medical and Laboratory Measurement.
Precision Bridge Sensor Front Ends
The ICL7652CPD+ fits low-level bridge and strain-gauge front ends where signal amplitude is small and low-frequency drift directly affects measurement accuracy. Its zero-drift architecture reduces amplifier-generated offset movement, while the listed 15 pA input bias current limits loading on high-impedance bridge outputs. The 450 kHz gain-bandwidth product supports modest-bandwidth instrumentation, and the 0.5 V/us slew rate can handle sensor transients without overdriving the amplifier. Designers should still verify the input common-mode range, offset-null behavior, and filter requirements for the particular bridge excitation and gain.
Được đề xuất
Low-Level Current Measurement
The ICL7652CPD+ is well suited to precision current measurement when the shunt voltage is small and the useful signal bandwidth remains below the amplifier's 450 kHz gain-bandwidth capability. The 15 pA input bias current is favorable for high-impedance sensing networks, while the zero-drift architecture reduces slow offset changes. Its 700 uV listed input offset still contributes to absolute error and should be included in the measurement budget. The 0.5 V/us slew rate provides adequate response for many slowly varying industrial currents, but system designers should include input filtering and verify that the shunt and amplifier do not introduce excessive thermal drift.
Được đề xuất
High-Impedance Sensor Signal Conditioning
The ICL7652CPD+ can condition signals from high-impedance sensors because its 15 pA input bias current limits DC loading and its zero-drift operation improves long-term low-frequency stability. With a 450 kHz gain-bandwidth product, it is appropriate for sensors whose information bandwidth is modest rather than high. A practical front end should use guarded or short PCB traces, add input filtering appropriate to the sensor, and keep the selected closed-loop gain low enough to preserve adequate bandwidth and phase margin. The 700 uV input offset specification remains relevant when translating small sensor outputs into engineering units.
Được đề xuất
Data Acquisition Signal Chains
The ICL7652CPD+ is applicable to low-level data-acquisition channels where reducing slow offset drift improves repeatability across temperature. Its 450 kHz gain-bandwidth product can support moderate-bandwidth amplification, and the 15 pA bias current reduces errors with high-source-impedance converters or sensors. Designers should limit loop gain according to the required channel bandwidth and verify the amplifier's stability with the chosen feedback network and sampling capacitance. The obsolete lifecycle status makes this configuration most appropriate for sustaining an existing installation or controlled legacy redesign rather than creating a new long-lived platform.
Được đề xuất
Precision Instrumentation Amplifiers
The ICL7652CPD+ can serve as the input stage of a discrete instrumentation amplifier when its 15 pA bias current and low-drift architecture are important. A three-amplifier topology can combine common-mode rejection with a configurable differential gain, but each added amplifier contributes offset, noise, and bandwidth limitations. The ICL7652CPD+ contributes a 450 kHz gain-bandwidth product and 0.5 V/us slew rate, making it most appropriate for laboratory or industrial measurements with limited bandwidth. Resistor matching and input bias-current balance must be checked carefully to prevent degradation of common-mode rejection.
Được đề xuất
Medical and Laboratory Measurement
The ICL7652CPD+ is suited to low-frequency medical or laboratory measurement circuits where leakage from the amplifier could disturb a high-impedance source. Its 15 pA input bias current is the key attraction, while the chopper-stabilized architecture helps reduce slow offset drift. The device must still meet the application's safety, isolation, qualification, and electromagnetic-compatibility requirements, which cannot be inferred from its amplifier specifications. Because the part is obsolete, medical and laboratory equipment programs should document the obsolescence risk, supply plan, and qualification of any replacement.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ICL7652CPD+ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ICL7652CPD | ICL7652CPD-2 | ICL7652CTV |
|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Package | 14-PDIP (0.300 inch, 7.62 mm) | 14-PDIP (0.300 inch, 7.62 mm) | 14-PDIP (0.300 inch, 7.62 mm) | 14-PDIP (0.300 inch, 7.62 mm) |
| Amplifier Type | Zero-Drift Operational Amplifier | Zero-Drift Operational Amplifier | Zero-Drift Operational Amplifier | Zero-Drift Operational Amplifier |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Gain-Bandwidth Product | 450 kHz | 450 kHz | 450 kHz | 450 kHz |
| Slew Rate | 0.5 V/us | 0.5 V/us | 0.5 V/us | 0.5 V/us |
| Input Bias Current | 15 pA | 15 pA | 15 pA | 15 pA |
| Input Offset Voltage | 700 uV | 700 uV | 700 uV | 700 uV |
Bảo phân biệt quan trọng
- Low input bias current supports high-impedance sources (vsICL7652CTV)
- Same-family 14-pin footprint supports orderly substitution (vsICL7652CPD-2)
- Lower listed gain-bandwidth product than the TLC2652 comparison family (vsTLC2652ACP)
Ghi chú thiết kế
Keep input and feedback traces short, and avoid routing high-impedance input nodes beside switching supplies, relay contacts, or digital clock lines. If the input source has high source impedance, use a guarded layout and consider a small input capacitance for noise filtering, but verify that the resulting pole does not destabilize the intended noise gain. The 15 pA input bias current makes leakage control important even though the amplifier's own bias contribution is low.
Do not select this amplifier solely because it is described as zero-drift. The 700 uV input offset remains part of the absolute-error budget, and the 450 kHz gain-bandwidth product must be divided by the required noise gain to estimate closed-loop bandwidth. Also check the 0.5 V/us slew rate against the largest expected output step. These three checks can prevent an otherwise suitable precision amplifier from failing accuracy, stability, or large-signal requirements.
Decouple the power pins close to the device with the capacitance and ESR range specified by the manufacturer datasheet. For chopper-stabilized amplifiers, power-supply ripple and chopping-related output artifacts may matter even when the dominant specification is input-offset drift. Evaluate the output over the intended measurement bandwidth and inspect the application circuit for residual modulation or clock-spectrum components before using the amplifier in sensitive measurements.
Thông tin tuân thủ
The exact lead-free, RoHS, REACH, AEC-Q100, halogen-free, and conflict-minerals declarations for ICL7652CPD+ require confirmation from the manufacturer product documentation.