ICS180M-51 - 28MHz Low EMI Clock Generator | Renesas
MPN: ICS180M-51 ✓ Hoạt độngICS180M-51 Tóm tắt
A clock generator is an integrated circuit that produces a stable timing reference for digital systems. It may accept an existing reference clock or a crystal and use a phase-locked loop, or PLL, to create a related output frequency. Clock generators are used to support processor timing, data conversion, communications, storage, and other digital subsystems. The ICS180M-51 belongs to the clock generator and timing-IC hierarchy rather than the general-purpose logic IC category.
The central feature of the ICS180M-51 is its low-EMI output. According to the ICS180-51 datasheet, the device offers center-spread selections of ±0.625% and ±1.875%. These selections allow a clock's spectral energy to be distributed across a wider frequency range, which can reduce the peak magnitude of narrowband emissions when used as an EMI mitigation technique. The single output stage uses CMOS signaling and has a listed 1:1 input-to-output ratio.
The ICS180-51 combines analog and digital PLL functions to derive its output from a clock or crystal input. This architecture allows a single device to operate as a low-EMI clock generator rather than requiring a separate fixed-frequency oscillator arrangement. The Renesas datasheet also identifies related MK1714-01 and MK1714-02 devices as references for a wider selection of input frequencies and multipliers when a design requires more flexible frequency translation than the ICS180-51 provides.
Typical uses include EMI-sensitive digital equipment, communications equipment, and systems requiring a low-EMI clock derived from an existing reference. The device is also suitable where spread-spectrum clocking is used to reduce discrete spectral components. It can serve as a timing reference for processors, interface circuits, converters, and other clocked digital logic where a CMOS output at up to 28 MHz is required.
When designing around the ICS180M-51, first confirm that the source frequency, selected spread mode, and required output frequency are supported by the device configuration. Place the clock input and output traces for controlled impedance and maintain short return paths to the device ground pins. Verify conducted and radiated emissions at the finished-product level because spread-spectrum timing alone does not establish regulatory compliance.
This page consolidates the device type, operating limits, spread-spectrum selections, package information, sourcing guidance, and design cautions into one engineering reference. It also provides practical application analysis, alternative-part qualification guidance, and a structured comparison framework for evaluating the ICS180M-51 against other low-EMI clock-generator options.
Bộ thay thế dễ dàng lắp đặt cho ICS180M-51 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
ICS180M-51LF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ICS180M-51T
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ICS180M-51 Thông số kỹ thuật
| Product Type | Spread spectrum clock generator |
| Cấu hình đầu ra | Single output |
| Maximum Frequency | 28 MHz |
| Input Sources | Clock or crystal |
| Kiểu đầu ra | CMOS |
| PLL | Yes |
| Number of Circuits | 1 |
| Input-to-Output Ratio | 1:1 |
| Center Spread Selection 1 | ±0.625% |
| Center Spread Selection 2 | ±1.875% |
| EMI Characteristic | Low EMI output |
| PLL Architecture | Proprietary mix of analog and digital PLL technology |
| Hộp | 8-pin SOIC |
| Kiểu lắp đặt | Surface mount |
| Datasheet Publication Date | 2012-03-28 |
Hướng dẫn cấu hình chân ICS180M-51 8-pin soic
Cấu hình chân cho ICS180M-51 (8-pin soic gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ICS180M-51.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ICS180M-51 phù hợp cho 6 Áp dụngs: EMI-Sensitive Digital Logic, Communications Equipment Clocking, Processor Interface Timing, Data Acquisition and Conversion Systems, Network and Storage Controller Clocks, Industrial Control Module Timing.
EMI-Sensitive Digital Logic
The ICS180M-51 fits digital systems that need a low-EMI clock with a selectable spread spectrum. Its center-spread options of ±0.625% and ±1.875% distribute clock energy over a wider frequency range, which can lower the peak magnitude seen at a narrow measurement band. The device accepts a clock or crystal source, provides one CMOS output, and uses a 1:1 input-to-output ratio. Place the generator close to the receiving logic, keep clock traces short, and verify both radiated and conducted emissions in the final assembly.
Được đề xuất
Communications Equipment Clocking
Communications equipment can use the ICS180M-51 to create a spread CMOS clock for timing sections that are sensitive to narrowband emissions. With clock or crystal input, a maximum listed frequency of 28 MHz, and selectable center spreading, the device suits moderate-speed digital rails. The 1:1 ratio simplifies clock-tree distribution, but board engineers should test the complete transmitter and receiver chain because data-line activity and power-converter switching can create additional emissions that clock spreading does not address.
Được đề xuất
Processor Interface Timing
The ICS180M-51 can provide a referenced CMOS clock for processors and interface logic that operate within the device's 28 MHz maximum frequency. Its clock or crystal input and 1:1 input-to-output ratio allow it to sit near the source or the load depending on board architecture. The selectable ±0.625% or ±1.875% spread may help reduce discrete clock harmonics. Confirm the receiving device's jitter, input-voltage, and clock-accuracy requirements before using the spread output as a precision reference.
Được đề xuất
Data Acquisition and Conversion Systems
Data converters and acquisition systems can use the ICS180M-51 as a low-EMI digital clock source when their sampling logic operates at a compatible frequency. The device supplies one CMOS output with a 1:1 ratio and offers ±0.625% or ±1.875% center spreading, helping reduce narrowband clock energy. Because converter accuracy may depend on clock quality, use spread-spectrum mode only when the acquisition system tolerates the resulting modulation, and verify timing margin and conversion performance with the complete signal chain.
Được đề xuất
Network and Storage Controller Clocks
Network-interface and storage-controller boards can benefit from a spread-spectrum clock when reducing discrete emissions is a design priority. The ICS180M-51 accepts a clock or crystal reference, delivers a CMOS output, and supports a maximum listed frequency of 28 MHz with a 1:1 ratio. Its low-EMI architecture is intended for this class of timing need. Route the output into the controller's clock input with a short, controlled-impedance trace, and confirm that the controller tolerates frequency modulation during its operating modes.
Được đề xuất
Industrial Control Module Timing
The ICS180M-51 is suitable for industrial control modules that need a compact clock source and selective spectrum spreading. Its 8-pin SOIC package supports surface-mount assembly, while the ±0.625% and ±1.875% center-spread settings give designers two EMI-tuning choices. A 1:1 input-to-output ratio keeps the clock path straightforward when the module already has a suitable reference. Validate operation across the full industrial temperature range and test conducted emissions at the product's power interfaces before release.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ICS180M-51 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Package | 8-pin SOIC |
| Brand | Renesas Electronics |
| Product Type | Low-EMI spread-spectrum clock generator |
| Maximum Frequency | 28 MHz |
| Input Sources | Clock or crystal |
| Output Type | CMOS |
| Number of Circuits | 1 |
| Input-to-Output Ratio | 1:1 |
| Center Spread Selections | ±0.625% and ±1.875% |
| PLL Architecture | Proprietary mix of analog and digital PLL technology |
Bảo phân biệt quan trọng
- Selectable center-spectrum spreading (vsFixed-frequency clock source)
- Flexible reference input (vsCrystal-only clock oscillator)
- Dedicated low-EMI PLL implementation (vsGeneric divider-based clock circuit)
Ghi chú thiết kế
Route the source and output clock as a controlled-impedance path and keep it as short as practical. Avoid unterminated stubs, excessive vias, and splits to unrelated loads, because these structures can create reflections and additional harmonics. Place the ICS180M-51 close to the circuit that is most sensitive to clock noise when the source-to-load distance would otherwise be long.
Select the center-spread range by measurement rather than by assumption: the ICS180M-51 provides ±0.625% and ±1.875% options. Measure radiated and conducted emissions with the spread setting disabled and enabled to identify the improvement and check that downstream logic tolerates the modulation. Spread-spectrum timing reduces concentrated spectral energy but does not correct unrelated switching or connector noise.
Confirm the receiver's clock-accuracy and jitter requirements before using a spread-spectrum output for a precision sampling or conversion path. The ±1.875% mode creates more frequency deviation than the ±0.625% mode and may leave less timing margin at the receiver. Validate with the complete source, trace, loading, and receiving-device configuration rather than relying only on nominal clock frequency.
Do not assume that any 8-pin spread-spectrum clock generator is interchangeable with the ICS180M-51. Check the actual pin mapping, supply requirements, crystal versus clock input arrangement, output enable behavior, output ratio, spread configuration, and frequency limits in the manufacturer datasheet. A candidate device must also preserve the 8-pin SOIC footprint and operate within the 28 MHz maximum frequency.
Thông tin tuân thủ
No explicit environmental or automotive compliance declarations were identified for ICS180M-51. Confirm the current compliance status and material declarations with Renesas for the exact ordering suffix and shipment configuration.