ICS508MIT - 250 MHz PECL-to-CMOS Converter | Renesas
MPN: ICS508MIT ✗ Cuối đờiICS508MIT Tóm tắt
A clock converter is a digital interface IC that translates one signaling standard into another while maintaining clock timing and frequency. In the broader semiconductor hierarchy, the ICS508MIT belongs to the clock and timing category rather than a PLL-based frequency synthesizer. It does not multiply, divide, or modulate the input clock; its primary function is level and logic-family conversion. This makes it suitable for systems in which an upstream serializer, transceiver, or other high-speed logic device generates a PECL clock but the receiving block requires a CMOS reference.
The ICS508MIT supports clock frequencies from 0 Hz to 250 MHz, as identified in the manufacturer datasheet information. Its input is PECL and its output is CMOS, with a 1:1 input-to-output ratio. Separate VDD supplies allow the input and output voltage domains to be configured independently. This separation is valuable when the source device uses one PECL supply arrangement while the destination logic operates at another CMOS voltage.
The device is offered in an 8-pin SOIC package and is associated with tape-and-reel ordering code MIT. Because it performs direct conversion rather than frequency synthesis, the ICS508MIT avoids the loop bandwidth, divider noise, and lock-acquisition considerations associated with PLL clock generators. Its timing performance therefore depends primarily on the quality of the incoming PECL clock and the integrity of the implemented circuit.
Typical uses include high-speed communications equipment, parallel data acquisition, telecommunications backplanes, test and measurement instruments, and digital subsystems that require CMOS clocking from a PECL source. In these applications, the converter can provide a clean CMOS reference while preserving the source clock's fundamental frequency. Input and output supply decoupling, controlled-impedance routing, and correct common-mode treatment of the PECL interface remain central implementation considerations.
Designers should follow the pin-description table in the manufacturer datasheet when assigning PCB tracks, and should verify signal amplitude, supply sequencing, and termination at the operating frequency. The SOIC footprint permits conventional surface-mount assembly, although package-parasitic effects and board loss become increasingly important as clock rates approach the 250 MHz upper limit.
This page combines the manufacturer-family specifications, package information, sourcing structure, interface guidance, and drop-in replacement analysis to support faster engineering evaluation. Use the Request a Quote form for current commercial availability, lead time, and ordering support.
Bộ thay thế dễ dàng lắp đặt cho ICS508MIT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ICS508MIT (cùng hình factor và footprint) — khác nhau ở Package, Supply Architecture.
ICS508M
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ICS508MIT Thông số kỹ thuật
| Product Type | PECL-to-CMOS clock converter |
| Clock Frequency Range | 0 Hz to 250 MHz |
| Tần số xung maksimum | 250 MHz |
| Input Logic | PECL |
| Output Logic | CMOS |
| Input-to-Output Ratio | 1:1 |
| PLL | No |
| Number of Circuits | 1 circuit |
| Differential Input | Yes |
| Differential Output | No |
| Supply Architecture | Separate VDD supplies for input and output voltage domains |
| Hộp | 8-pin SOIC |
| Terminal Count | 8 terminals |
| Kiểu lắp đặt | Surface mount |
| Ordering Code | MIT tape-and-reel ordering code |
| Manufacturer | Renesas Electronics Corporation |
Hướng dẫn cấu hình chân ICS508MIT 8-pin soic
Cấu hình chân cho ICS508MIT (8-pin soic gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ICS508MIT.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ICS508MIT phù hợp cho 6 Áp dụngs: High-Speed Communications Clocking, Telecommunications Backplane Conversion, Parallel Data-Acquisition Systems, Test and Measurement Instrumentation, Industrial Digital Control, Clock-Distribution Interface.
High-Speed Communications Clocking
The ICS508MIT is suitable for communications subsystems in which a serializer, transceiver, or parallel-link device produces a PECL clock and downstream logic requires CMOS. The converter preserves the source frequency with a 1:1 input-to-output ratio and supports clock rates up to 250 MHz, allowing the two signaling domains to coexist without introducing a PLL. Its separate input and output VDD supplies permit voltage-domain adjustment, but the PECL source amplitude, common-mode voltage, and termination must follow the manufacturer interface requirements.
Được đề xuất
Telecommunications Backplane Conversion
In a telecommunications backplane, a central timing source may use PECL to preserve signal integrity over controlled-impedance routes while local digital processors require CMOS clock inputs. The ICS508MIT provides a direct PECL-to-CMOS conversion path up to 250 MHz without frequency multiplication or division. Place it near the receiving logic when possible, provide solid supply bypassing, and preserve a continuous ground reference. The implementation must account for source-termination distance, clock skew, and any loss introduced by connectors or long backplane traces.
Được đề xuất
Parallel Data-Acquisition Systems
The ICS508MIT can convert a PECL sampling clock into a CMOS clock for a parallel ADC, FPGA, or data-processing section. Its 1:1 ratio preserves the sampling cadence, and the 250 MHz upper limit supports demanding acquisition architectures. The principal design consideration is edge quality: source amplitude, rise time, jitter, and return loss influence how much timing margin remains after conversion. Short routing, appropriate CMOS load management, and local decoupling help maintain deterministic clock arrival at the destination device.
Được đề xuất
Test and Measurement Instrumentation
Instrumentation commonly combines high-speed PECL timing with lower-voltage CMOS control or processing logic. The ICS508MIT provides a focused interface between those domains while preserving clock frequency and avoiding the complexity of PLL acquisition. It is useful near a counter, analyzer, or display-processing chain where a clean CMOS reference is required. To retain measurement quality, isolate noisy analog and switching circuitry from the clock path, use low-inductance supply connections, and validate the output edge at the highest operating frequency and temperature condition.
Được đề xuất
Industrial Digital Control
An industrial controller may receive a 250 MHz-class timing reference from a dedicated high-speed source while its logic sections operate from CMOS supplies at a different voltage. The ICS508MIT's separate VDD domains allow the input and output interfaces to be biased independently, simplifying interface planning where standard voltage levels do not align. The device should remain on a controlled clock island with stable return paths and local decoupling. Designers must verify that the CMOS output voltage is accepted by the destination logic and that the clock meets its setup and hold requirements.
Được đề xuất
Clock-Distribution Interface
The ICS508MIT is useful at the boundary between a PECL clock source and a CMOS distribution network. Rather than distributing PECL throughout the board, the converter can establish a CMOS reference close to the receiving logic and reduce the number of high-speed ECL loads. Because the device has no PLL, it does not correct input jitter or provide programmable phase adjustment. Its value is therefore in clean format conversion and localized distribution. Maintain short output traces, avoid excessive capacitive loading, and verify downstream fanout requirements independently.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ICS508MIT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ICS508 |
|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics |
| Package | 8-pin SOIC | 8-pin SOIC |
| Product Function | PECL-to-CMOS clock converter | PECL-to-CMOS clock converter |
| Maximum Clock Frequency | 250 MHz | 250 MHz |
| Clock Frequency Range | 0 Hz to 250 MHz | 0 Hz to 250 MHz |
| Input Logic | PECL | PECL |
| Output Logic | CMOS | CMOS |
| Input-to-Output Ratio | 1:1 | 1:1 |
| PLL | No | No |
| Supply Architecture | Separate VDD supplies | Separate VDD supplies |
Bảo phân biệt quan trọng
- Direct PECL-to-CMOS clock conversion without a PLL (vsGeneral-purpose PLL clock generators)
- Independent input and output supply domains (vsSingle-supply CMOS clock buffers)
- Compact 8-pin SOIC implementation (vsDiscrete PECL receivers and clock buffers)
Ghi chú thiết kế
Place the ICS508MIT close to the CMOS destination and keep the PECL input route short, continuous, and referenced to a solid ground plane. Use the manufacturer's recommended PECL source termination and common-mode arrangement. At clock rates approaching 250 MHz, route stubs, test pads, connectors, and layer transitions can reflect energy back into the converter; minimize those discontinuities and preserve controlled impedance on both signaling domains.
Decouple each VDD supply independently with the capacitance and placement specified by the manufacturer datasheet. Keep the two domains' return currents disciplined, especially when the PECL and CMOS supply voltages differ. Confirm the allowable supply range, sequencing requirements, and output-load limits for the exact ordering code before power-up. Because no operating-current values are stated in the available family information, use the manufacturer electrical table for a valid dissipation calculation.
Do not treat a generic family designation as a finished drop-in substitute until its exact suffix and pin table have been checked. Also avoid assuming that any PECL source can drive the input at the intended frequency: source amplitude, common-mode voltage, edge rate, duty cycle, and jitter all affect timing margin. Validate the complete path with an oscilloscope or suitable clock analyzer at the highest expected frequency and across the required temperature range.
Thông tin tuân thủ
The available product information does not state exact-MPN compliance declarations. AEC-Q100 is not applicable because this device is not identified as an automotive-qualified product.