Renesas Electronics

ICS508MIT - 250 MHz PECL-to-CMOS Converter | Renesas

料号: ICS508MIT ✗ 停产
Separate VDD supplies for input and output voltage domains Vdss 8-pin SOIC Package 0 Hz to 250 MHz Speed
最小起订量: 1 |

ICS508MIT 概述

Renesas Electronics ICS508MIT is a PECL-to-CMOS clock converter with a maximum operating frequency of 250 MHz, packaged in an 8-pin SOIC. The device accepts a PECL clock input and produces a high-quality CMOS clock output, providing a practical interface between differential clocking systems and conventional CMOS logic. Its one-to-one input-to-output ratio preserves the incoming clock frequency, while separate supply domains support voltage translation between the PECL input and CMOS output sections.

A clock converter is a digital interface IC that translates one signaling standard into another while maintaining clock timing and frequency. In the broader semiconductor hierarchy, the ICS508MIT belongs to the clock and timing category rather than a PLL-based frequency synthesizer. It does not multiply, divide, or modulate the input clock; its primary function is level and logic-family conversion. This makes it suitable for systems in which an upstream serializer, transceiver, or other high-speed logic device generates a PECL clock but the receiving block requires a CMOS reference.

The ICS508MIT supports clock frequencies from 0 Hz to 250 MHz, as identified in the manufacturer datasheet information. Its input is PECL and its output is CMOS, with a 1:1 input-to-output ratio. Separate VDD supplies allow the input and output voltage domains to be configured independently. This separation is valuable when the source device uses one PECL supply arrangement while the destination logic operates at another CMOS voltage.

The device is offered in an 8-pin SOIC package and is associated with tape-and-reel ordering code MIT. Because it performs direct conversion rather than frequency synthesis, the ICS508MIT avoids the loop bandwidth, divider noise, and lock-acquisition considerations associated with PLL clock generators. Its timing performance therefore depends primarily on the quality of the incoming PECL clock and the integrity of the implemented circuit.

Typical uses include high-speed communications equipment, parallel data acquisition, telecommunications backplanes, test and measurement instruments, and digital subsystems that require CMOS clocking from a PECL source. In these applications, the converter can provide a clean CMOS reference while preserving the source clock's fundamental frequency. Input and output supply decoupling, controlled-impedance routing, and correct common-mode treatment of the PECL interface remain central implementation considerations.

Designers should follow the pin-description table in the manufacturer datasheet when assigning PCB tracks, and should verify signal amplitude, supply sequencing, and termination at the operating frequency. The SOIC footprint permits conventional surface-mount assembly, although package-parasitic effects and board loss become increasingly important as clock rates approach the 250 MHz upper limit.

This page combines the manufacturer-family specifications, package information, sourcing structure, interface guidance, and drop-in replacement analysis to support faster engineering evaluation. Use the Request a Quote form for current commercial availability, lead time, and ordering support.

直接替换替代料: ICS508MIT ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: ICS508MIT (相同外形与封装尺寸) ——差异在于 Package, Supply Architecture.

Renesas Electronics
Package: 8-pin SOIC, 3.90 mm width
Supply Architecture: Separate VDD supplies for input and output sections
对比 ICS508MIT →

ICS508M

✅ 直接替换
Renesas Electronics
📦 8-pin SOIC
PECL-to-CMOS clock converter · 250 MHz · PECL · CMOS · 1 circuit · 1:1 · No · Yes

联系询价

查看数据手册 →

ICS508MIT 规格参数

Product Type PECL-to-CMOS clock converter
Clock Frequency Range 0 Hz to 250 MHz
最大时钟频率 250 MHz
Input Logic PECL
Output Logic CMOS
Input-to-Output Ratio 1:1
PLL No
Number of Circuits 1 circuit
Differential Input Yes
Differential Output No
Supply Architecture Separate VDD supplies for input and output voltage domains
封装 8-pin SOIC
Terminal Count 8 terminals
安装类型 Surface mount
Ordering Code MIT tape-and-reel ordering code
Manufacturer Renesas Electronics Corporation

ICS508MIT 8-pin soic 引脚配置指南

ICS508MIT(8-pin soic 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

ICS508MIT 的 8-pin soic 封装引脚图

暂无详细引脚数据: ICS508MIT.

请参阅 数据手册 以查看完整引脚配置。

典型应用

ICS508MIT 适用于 6 应用s: High-Speed Communications Clocking, Telecommunications Backplane Conversion, Parallel Data-Acquisition Systems, Test and Measurement Instrumentation, Industrial Digital Control, Clock-Distribution Interface.

🌐

High-Speed Communications Clocking

The ICS508MIT is suitable for communications subsystems in which a serializer, transceiver, or parallel-link device produces a PECL clock and downstream logic requires CMOS. The converter preserves the source frequency with a 1:1 input-to-output ratio and supports clock rates up to 250 MHz, allowing the two signaling domains to coexist without introducing a PLL. Its separate input and output VDD supplies permit voltage-domain adjustment, but the PECL source amplitude, common-mode voltage, and termination must follow the manufacturer interface requirements.

🌐

Telecommunications Backplane Conversion

In a telecommunications backplane, a central timing source may use PECL to preserve signal integrity over controlled-impedance routes while local digital processors require CMOS clock inputs. The ICS508MIT provides a direct PECL-to-CMOS conversion path up to 250 MHz without frequency multiplication or division. Place it near the receiving logic when possible, provide solid supply bypassing, and preserve a continuous ground reference. The implementation must account for source-termination distance, clock skew, and any loss introduced by connectors or long backplane traces.

🖥️

Parallel Data-Acquisition Systems

The ICS508MIT can convert a PECL sampling clock into a CMOS clock for a parallel ADC, FPGA, or data-processing section. Its 1:1 ratio preserves the sampling cadence, and the 250 MHz upper limit supports demanding acquisition architectures. The principal design consideration is edge quality: source amplitude, rise time, jitter, and return loss influence how much timing margin remains after conversion. Short routing, appropriate CMOS load management, and local decoupling help maintain deterministic clock arrival at the destination device.

🔧

Test and Measurement Instrumentation

Instrumentation commonly combines high-speed PECL timing with lower-voltage CMOS control or processing logic. The ICS508MIT provides a focused interface between those domains while preserving clock frequency and avoiding the complexity of PLL acquisition. It is useful near a counter, analyzer, or display-processing chain where a clean CMOS reference is required. To retain measurement quality, isolate noisy analog and switching circuitry from the clock path, use low-inductance supply connections, and validate the output edge at the highest operating frequency and temperature condition.

🏭

Industrial Digital Control

An industrial controller may receive a 250 MHz-class timing reference from a dedicated high-speed source while its logic sections operate from CMOS supplies at a different voltage. The ICS508MIT's separate VDD domains allow the input and output interfaces to be biased independently, simplifying interface planning where standard voltage levels do not align. The device should remain on a controlled clock island with stable return paths and local decoupling. Designers must verify that the CMOS output voltage is accepted by the destination logic and that the clock meets its setup and hold requirements.

🖥️

Clock-Distribution Interface

The ICS508MIT is useful at the boundary between a PECL clock source and a CMOS distribution network. Rather than distributing PECL throughout the board, the converter can establish a CMOS reference close to the receiving logic and reduce the number of high-speed ECL loads. Because the device has no PLL, it does not correct input jitter or provide programmable phase adjustment. Its value is therefore in clean format conversion and localized distribution. Maintain short output traces, avoid excessive capacitive loading, and verify downstream fanout requirements independently.

What is the ICS508MIT used for?
The ICS508MIT is an 8-pin PECL-to-CMOS clock converter designed to translate a PECL clock into a CMOS clock without changing its frequency. According to the ICS508 manufacturer-family information, it supports clocks from 0 Hz to 250 MHz and maintains a 1:1 input-to-output ratio. It is useful when a high-speed communications or test block generates a PECL clock but the receiving digital logic requires a CMOS reference.
What is the maximum frequency of the ICS508MIT?
The ICS508MIT supports a maximum clock frequency of 250 MHz. The ICS508 family datasheet identifies an operating clock range of 0 Hz to 250 MHz. This rating applies to the signal conditions and supply configurations defined by the manufacturer, so source amplitude, rise time, jitter, trace impedance, and termination must also be considered when operating near the upper frequency limit.
Where can I download the ICS508MIT datasheet PDF?
The ICS508MIT datasheet is available through the linked manufacturer-family datasheet page at AllDataSheet and through the ICS508 family datasheet listing. The document identifies the ICS508 as a PECL-to-CMOS converter, specifies an 8-pin SOIC or die packaging option, and lists a 0 Hz to 250 MHz clock range. Use the package-specific pin table when assigning PCB connections.
Where can I find the ICS508MIT pinout?
The ICS508MIT pinout is defined in the pin-description section of the manufacturer datasheet for the 8-pin SOIC package. The device uses separate VDD supply domains for its PECL input and CMOS output sections. Use the exact pin numbering and signal descriptions from that table when assigning nets, and place bypass capacitors adjacent to the relevant supply pins.
Does the ICS508MIT multiply or divide the input clock?
No, the ICS508MIT preserves the input clock frequency through a 1:1 input-to-output ratio. It is a logic-family and voltage-domain converter, not a PLL-based clock synthesizer. The ICS508 family information identifies PLL as absent, which means the device does not provide programmable multiplication, division, jitter attenuation, or lock acquisition; clock quality therefore follows the source and the implemented board environment.
What is the difference between PECL and CMOS clock signaling?
PECL and CMOS clocks use different voltage conventions, interface arrangements, and termination practices. The ICS508MIT accepts a differential PECL clock and produces a single-ended CMOS output, with separate VDD supplies supporting the two voltage domains. The PECL side requires correct common-mode treatment and source termination, while the CMOS side should use a defined reference plane and an appropriate trace impedance.
When should I choose the ICS508MIT over a PLL clock generator?
Choose the ICS508MIT when the goal is to convert an existing PECL clock to CMOS while preserving its frequency. A PLL clock generator is preferable when the design requires programmable multiplication, division, jitter filtering, or generation from a lower-frequency reference. The ICS508MIT offers a simpler 1:1 path with no PLL, making it suitable for high-speed clock distribution where source timing quality is already adequate.
What is the best drop-in replacement for the ICS508MIT?
A valid drop-in replacement must use the same 8-pin SOIC footprint, preserve the PECL input and CMOS output assignments, and remain suitable across the required clock frequency. No manufacturer-published substitute MPN appears in the available cross-reference material. Use the Request a Quote form and identify the required frequency, supplies, and package before accepting a proposed replacement, then compare its pinout and timing specifications with the manufacturer datasheet.
Can an ICS508 replace the ICS508MIT without PCB changes?
The ICS508 family description indicates 8-pin SOIC packaging and the same PECL-to-CMOS conversion function, but the available material does not establish that the base ICS508 designation is a finished, pin-compatible replacement for the MIT ordering code. Treat ICS508 as a family reference until the manufacturer ordering guide confirms the exact suffix, pin configuration, supply options, and lifecycle status. Do not approve a substitution based on the family name alone.
What is the difference between the ICS508MIT and a clock buffer?
The ICS508MIT changes the electrical signaling standard from differential PECL to CMOS, while a conventional clock buffer generally reproduces a clock within one logic family. Its separate input and output supplies make it more than a simple fan-out buffer. It is appropriate when the clock source and destination use incompatible logic conventions; use a buffer when both sides already use compatible CMOS or differential clocking.
How should I design the PCB layout for the ICS508MIT?
Place supply bypass capacitors close to their corresponding VDD and ground pins, and keep the PECL input route short with controlled impedance and correct source termination. Route the CMOS output over a continuous reference plane with a destination-appropriate impedance. Avoid long stubs and unnecessary test-point branches because parasitic capacitance and inductance can degrade clock edges as the operating rate approaches 250 MHz.
How much power does the ICS508MIT dissipate?
The power dissipation depends on the separate input and output supply voltages, clock activity, and CMOS output load. The available family information does not state current consumption or power dissipation, so a numerical calculation would be speculative. Calculate each rail from its actual operating current, multiply by its voltage, and sum the rail powers before checking the SOIC assembly's temperature rise against the application environment.
Where can I buy the ICS508MIT?
Use the Request a Quote form on this page to request the current ICS508MIT price, stock position, minimum order quantity, and lead time. The target is listed under Renesas Electronics Corporation as an 8-pin SOIC device with tape-and-reel ordering code MIT. The form is the appropriate route for an exact-MPN commercial request and avoids reliance on stale catalog pricing.
Is the ICS508MIT in stock?
Current stock for the exact ICS508MIT should be confirmed through the Request a Quote form on this page. The available product listings confirm the MPN, manufacturer association, package, and ordering code, but they do not establish a reliable current inventory quantity. Include your required quantity, date-sensitive schedule, and acceptable packaging configuration when requesting availability.
What is the lead time for the ICS508MIT?
The current lead time for the ICS508MIT depends on inventory, factory schedule, order quantity, and lifecycle status. Use the Request a Quote form to request a date-confirmed lead time for the exact 8-pin SOIC ordering code. For production planning, provide your required annual usage and forecast so the quotation can distinguish material availability from allocation constraints.
Is the ICS508MIT compliant with RoHS and REACH?
The RoHS and REACH status of the exact ICS508MIT is not stated in the available manufacturer-family information. Check the current manufacturer product declaration or material-compliance report before using the device in a regulated supply chain. Do not infer compliance from its age, package, or manufacturer alone, and retain the applicable declaration with purchasing and qualification records.

工程参考数据: ICS508MIT ——对比、设计指导和合规信息。

选型指南

Choose the ICS508MIT when a system already has a high-quality PECL clock but requires a CMOS clock at the destination, particularly when the input and output logic use different supply domains. Its 1:1 conversion and 250 MHz capability make it a direct interface device rather than a frequency synthesizer. Select a PLL-based clock generator instead when the design needs programmable multiplication, division, phase adjustment, jitter attenuation, or synchronization to a reference clock. Do not approve the ICS508 family designation as a replacement until the exact ordering suffix and pin configuration are confirmed. For production use, verify the complete electrical limits, supply requirements, propagation behavior, and lifecycle status from the manufacturer datasheet, and validate the PCB implementation at the highest intended clock frequency.

与替代料对比

参数 本产品 ICS508
Brand Renesas Electronics Renesas Electronics
Package 8-pin SOIC 8-pin SOIC
Product Function PECL-to-CMOS clock converter PECL-to-CMOS clock converter
Maximum Clock Frequency 250 MHz 250 MHz
Clock Frequency Range 0 Hz to 250 MHz 0 Hz to 250 MHz
Input Logic PECL PECL
Output Logic CMOS CMOS
Input-to-Output Ratio 1:1 1:1
PLL No No
Supply Architecture Separate VDD supplies Separate VDD supplies

关键差异点

  • Direct PECL-to-CMOS clock conversion without a PLL (对比 General-purpose PLL clock generators)
  • Independent input and output supply domains (对比 Single-supply CMOS clock buffers)
  • Compact 8-pin SOIC implementation (对比 Discrete PECL receivers and clock buffers)

设计说明

Place the ICS508MIT close to the CMOS destination and keep the PECL input route short, continuous, and referenced to a solid ground plane. Use the manufacturer's recommended PECL source termination and common-mode arrangement. At clock rates approaching 250 MHz, route stubs, test pads, connectors, and layer transitions can reflect energy back into the converter; minimize those discontinuities and preserve controlled impedance on both signaling domains.

Decouple each VDD supply independently with the capacitance and placement specified by the manufacturer datasheet. Keep the two domains' return currents disciplined, especially when the PECL and CMOS supply voltages differ. Confirm the allowable supply range, sequencing requirements, and output-load limits for the exact ordering code before power-up. Because no operating-current values are stated in the available family information, use the manufacturer electrical table for a valid dissipation calculation.

Do not treat a generic family designation as a finished drop-in substitute until its exact suffix and pin table have been checked. Also avoid assuming that any PECL source can drive the input at the intended frequency: source amplitude, common-mode voltage, edge rate, duty cycle, and jitter all affect timing margin. Validate the complete path with an oscilloscope or suitable clock analyzer at the highest expected frequency and across the required temperature range.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The available product information does not state exact-MPN compliance declarations. AEC-Q100 is not applicable because this device is not identified as an automotive-qualified product.

数据核验日期: 2026-11-16 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

ICS508MIT datasheet ICS508MIT pinout ICS508MIT datasheet pdf ICS508MIT specifications ICS508MIT 250 MHz ICS508MIT PECL CMOS converter ICS508MIT 8-SOIC ICS508MIT replacement ICS508MIT equivalent ICS508MIT price ICS508MIT stock Renesas ICS508MIT

相关元器件 & 术语

Renesas Electronics ICS508MIT ICS508 PECL CMOS PECL-to-CMOS converter clock converter clock and timing IC logic interface digital semiconductor 250 MHz clock 1:1 clock ratio differential input single-ended output separate VDD supplies 8-pin SOIC SOIC family surface-mount package clock distribution telecommunications backplane data acquisition industrial control test and measurement high-speed communications
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情