ICS525-01R - 160MHz User-Configurable Clock | Renesas
MPN: ICS525-01R ⚠ Lần mua cuốiICS525-01R Tóm tắt
A user-configurable clock, commonly called OSCaR, is a clock-generation IC whose output configuration is established with hardware select pins rather than a fixed factory divider ratio. The ICS525-01/02 family accepts a crystal or clock input and can generate nearly any supported output frequency from that source. Grounding or floating the configuration pins selects the required operating mode, making the ICS525-01R useful where the design must be adjusted without changing external components.
Key features include a 160 MHz maximum output frequency, single-clock fanout capability, configuration through select pins, and operation from either a crystal or an external clock source. The 150 mil-body, 28-pin SSOP construction provides enough routing flexibility for a clock tree while remaining compatible with established surface-mount assembly methods. The -01R ordering suffix identifies the 160 MHz configuration within the ICS525 family.
The ICS525-01R is part of the ICS525-01/02 family, whose architecture replaces a conventional crystal oscillator plus a separate divider or fanout arrangement with one configurable clock circuit. Its select-pin control allows a board designer to define the clock relationship required by processors, transceivers, converters, and data-conversion equipment. This integration reduces the number of discrete timing components while preserving accurate frequency relationships across the system.
Typical uses include retrofitting a clock into an existing board, generating related clocks for multiple digital loads, supporting communication interfaces, and producing clocks for converters or test equipment. Because the family supports both crystal and external-clock drive, the device can suit new designs and legacy repairs where an original oscillator configuration is difficult to source.
When assigning a replacement, confirm the selected frequency table, input-source arrangement, and output configuration against the board's original design. Place the clock source and decoupling close to the device, and route clock outputs as short, controlled-impedance traces. The select pins must be left grounded or floating as specified by the configuration table; do not add pull-up or pull-down resistors unless the board design requires them.
This page adds practical configuration guidance, verified package and frequency information, a drop-in comparison, and sourcing guidance to the basic manufacturer datasheet information, helping engineers evaluate the ICS525-01R for both new designs and legacy clock-tree repairs.
Bộ thay thế dễ dàng lắp đặt cho ICS525-01R — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
525-01RILF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
525-01RLF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ICS525-01RI
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ICS525-01R Thông số kỹ thuật
| Product Type | User-configurable clock generator and fanout distribution IC |
| Maximum Output Frequency | 160 MHz |
| Number of Clock Outputs | 1 output |
| Input Sources | Crystal or external clock input |
| Configuration Method | Select pins grounded or floated |
| Hộp | 28-pin SSOP, 0.154 inch (3.90 mm) width |
| Package Body | 150 mil body |
| Kiểu lắp đặt | Surface mount |
| Output Frequency Configuration | Nearly any supported output frequency from the selected input |
Hướng dẫn cấu hình chân ICS525-01R 150 mil body
Cấu hình chân cho ICS525-01R (150 mil body gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ICS525-01R.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ICS525-01R phù hợp cho 6 Áp dụngs: Legacy Crystal-Oscillator Replacement, Multi-Domain Digital Clock Distribution, Data-Conversion System Clocking, Communication Interface Clocking, Industrial Control Module Timing, Test and Measurement Equipment.
Legacy Crystal-Oscillator Replacement
The ICS525-01R is suited to replacing a discrete crystal oscillator when the replacement board must preserve an established clock architecture. It can accept a crystal or external clock input, and its select pins define the relationship between the reference and the generated output. The 160 MHz maximum output gives adequate headroom for legacy processor, bus, and controller timing domains. The important qualification is that the original reference frequency, crystal load network, configuration pins, and output routing must be reproduced. This makes the device particularly useful for repair and modernization programs involving older equipment that still relies on a 28-pin SSOP clock circuit.
Được đề xuất
Multi-Domain Digital Clock Distribution
The ICS525-01R fits clock-distribution work where related clock signals are needed across several digital blocks but a multi-output clock generator would be unnecessary. Its single configurable output, supported by the ICS525-01/02 selection method, can replace separate oscillator and divider arrangements. Configuration is established by grounding or floating the select pins rather than adding external programming components. The 160 MHz capability supports demanding digital subsystems while the 28-pin SSOP package provides enough physical routing room for clock input, selection, and output connections in an established surface-mount layout.
Được đề xuất
Data-Conversion System Clocking
The ICS525-01R can supply the sampling clock for a mixed-signal or data-conversion subsystem that requires a known relationship between a crystal reference and its digital processing clock. With a maximum output frequency of 160 MHz, it covers the clocking requirements of many converters and interface blocks while occupying one 28-pin SSOP position. The design advantage is configurability: select-pin settings allow the same board architecture to cover different clock relationships. When using the part with high-speed converters, keep clock traces short, provide the specified decoupling, and confirm output-edge requirements and jitter in the manufacturer datasheet before final sign-off.
Được đề xuất
Communication Interface Clocking
The ICS525-01R is applicable to communication equipment that needs a configurable clock reference alongside a crystal-based backplane or transceiver architecture. Its ability to derive a supported output from a crystal or external clock input makes it useful for maintaining clock relationships across legacy serial interfaces. The 160 MHz maximum output frequency supports high-rate digital processing, while the single-output configuration avoids unnecessary fanout logic when only one derived clock is required. Validation should include margin for the interface's reference tolerance, the exact select-pin state, clock-edge requirements, and the maximum loading presented by the connected transceiver.
Được đề xuất
Industrial Control Module Timing
The ICS525-01R can serve industrial control modules that retain an SSOP-based clock design and need a replaceable timing source. Its configurable operating modes help accommodate different processor, counter, and communication clock requirements without redesigning the entire clock tree. The 28-SSOP package is particularly useful where board area is constrained and a converter with a larger footprint is undesirable. For industrial equipment, qualify the exact configuration at the temperature extremes and verify supply tolerance, startup behavior, and clock-edge margins. The part is a practical maintenance solution for obsolete controller boards where a fixed modern oscillator would require a different footprint.
Được đề xuất
Test and Measurement Equipment
The ICS525-01R is suitable for test and measurement equipment that derives a precise operating clock from a crystal-controlled reference. The configurable architecture makes it possible to reproduce several clock relationships while retaining one package and board footprint, which is helpful in aging instruments and modular test platforms. A 160 MHz ceiling supports fast logic and interface sections, although the exact output must remain within the frequency limit of the selected 525-01 configuration. Instrument designers should pay particular attention to jitter, edge rates, and ground-return design when the clock drives sensitive conversion or measurement circuitry.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ICS525-01R — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | 525-01RILF | 525-01RLF | ICS525-01RI |
|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 28-SSOP | 28-SSOP | 28-SSOP | 28-SSOP |
| Product Type | Clock generator, fanout distribution IC | Clock generator, fanout distribution IC | User-configurable clock | Clock generator, fanout distribution IC |
| Input Source | Crystal or clock input | Crystal or clock input | Crystal or clock input | Crystal or clock input |
| Configuration Method | Select pins grounded or floated | Select-pin configuration | Select-pin configuration | Select-pin configuration |
| Package Body Width | 150 mil (3.90 mm) | 150 mil (3.90 mm) | 150 mil (3.90 mm) | 150 mil (3.90 mm) |
Bảo phân biệt quan trọng
- Higher documented maximum output frequency than the 140 MHz family alternatives (vs525-01RILF)
- Selectable clock configuration within the same 28-pin SSOP footprint (vsICS525-01RI)
- Documented terminal and package consistency for replacement designs (vs525-01RLF)
Ghi chú thiết kế
Reproduce the original reference-clock topology before fitting the ICS525-01R. Confirm whether the circuit uses a crystal or an external clock source, retain the required load components, and place them close to the device pins. Configuration is established by grounding or floating the select pins, so leave those nets in their documented states. Also preserve the original ground-return arrangement around the clock source, because long crystal or reference-clock traces can make an otherwise compatible replacement unstable.
Route the clock output as a short, controlled-impedance trace with a continuous ground reference and avoid unnecessary test pads or stub branches. The ICS525-01R can operate at up to 160 MHz, where edge rate and return-path discontinuities can create reflections or coupling into adjacent signals. Confirm the load capacitance and maximum clocking requirements of the connected block, then use the output-edge and capacitive-load limits from the manufacturer datasheet to determine whether series damping or an external buffer is required.
Do not treat the similar 525-01 and 525-02 family members as interchangeable without checking the configuration table. A replacement is valid only when the input source, output frequency, select-pin states, supply requirements, and timing limits match the original circuit. In particular, the documented 140 MHz alternatives do not meet a design that requires the ICS525-01R's full 160 MHz range. Validate startup and maximum-frequency operation in the final board rather than relying solely on package compatibility.
Provide local bypass capacitance exactly as specified in the manufacturer application guidance and keep the supply return path short. The clock generator's supply reference should share a low-impedance ground region with the digital circuitry it clocks, avoiding long current loops between bypass components and pins. Because this is a legacy remainder-market device, confirm that the exact manufacturer configuration and lot are available before committing a design, and qualify the replacement across its required voltage and temperature conditions.
Thông tin tuân thủ
The ICS525-01R is identified as a discontinued item with only remainder stock available. Compliance declarations are not stated on the distributor pages and should be confirmed with Renesas for the exact lot before use in new regulated production.