IDTADC1006S055H-C1 - 10-bit 55MSPS Flash ADC | Renesas
MPN: IDTADC1006S055H-C1 ✗ Cuối đờiIDTADC1006S055H-C1 Tóm tắt
What is a flash ADC? A flash ADC is the fastest ADC architecture, using 2^N - 1 parallel comparators to convert an analog signal in a single clock cycle. The 10-bit IDTADC1006S055H-C1 therefore contains up to 1023 comparators and a reference-ladder resistor network, placing it in the broader hierarchy of ADC -> data converter -> data acquisition IC -> signal chain IC -> semiconductor. Flash architecture trades power and die area for very high conversion rates without the latency of successive-approximation (SAR) or pipelined converters.
Key features include 55 MSPS sampling, 10-bit resolution, single-channel input, integrated sample-and-hold with a 1:1 input-to-output ratio, internal or external reference selection, and parallel CMOS outputs. Operating from a single 5V analog rail plus 5V digital supply keeps the bill of materials simple in legacy 5V systems, while the 44-QFP industrial-standard footprint allows existing PCB layouts to be reused without redesign.
The flash topology provides single-cycle latency, which is critical for instrumentation, radar IF digitisation, and digital oscilloscope front-ends where aliasing must be avoided and timing determinism matters. Unlike pipelined ADCs that introduce several clock cycles of latency, the flash converter's output appears within one conversion cycle - useful for control loops that close on the digitized waveform.
Typical applications include digital oscilloscopes, IF-sampling communications receivers, medical imaging front-ends, radar signal processing, and industrial test & measurement. The 55 MSPS rate supports digitisation of IF bands up to ~25 MHz under Nyquist, making it well suited for narrowband digital receivers and baseband signal processing.
When designing with this part, choose the internal reference for lowest external component count, or an external low-impedance reference (e.g., ADR01) to lower integral nonlinearity and gain drift. Decouple AVDD and DVDD separately with 0.1 uF plus 10 uF ceramic capacitors placed close to the pins, and provide a clean, low-jitter sampling clock on the CLK input to preserve SNR. This page synthesises distributor pricing, package diagrams, and cross-reference notes that complement the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho IDTADC1006S055H-C1 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với IDTADC1006S055H-C1 (cùng hình factor và footprint) — khác nhau ở Package, Architecture, Resolution, Analog Supply Voltage, Input Type.
IDTADC1006S070H-C1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →IDTADC1006S040H-C1
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADS5102IPFBR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADS5220PFBRG4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADC10062CIWM/NOPB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →IDTADC1006S055H-C1 Tỷ lệ tối đa & tính chất điện
| Độ phân giải | 10 bit |
| Tỷ lệ lấy mẫu | 55 MSPS |
| Number of Inputs | 1 |
| Input Type | Single-Ended |
| Architecture | Flash |
| Number of Converters | 1 |
| Data Interface | Parallel CMOS |
| Reference Type | External, Internal |
| Ratio S/H:ADC | 1:1 |
| Analog Supply Voltage | 5 V |
| Digital Supply Voltage | 5 V |
| Hộp | 44-QFP (10x10 mm) |
| Kiểu lắp đặt | Surface Mount |
Cấu hình chân IDTADC1006S055H-C1
| Chân 1 | AVDD — Analog 5V supply |
| Chân 2 | AVDD — Analog 5V supply |
| Chân 3 | AGND — Analog ground |
| Chân 4 | AIN — Analog input |
| Chân 5 | REFOUT — Internal reference output |
| Chân 6 | REFIN — Reference input |
| Chân 7 | AVDD — Analog 5V supply |
| Chân 8 | AGND — Analog ground |
| Chân 9 | D9 — Data output bit 9 (MSB) |
| Chân 10 | D8 — Data output bit 8 |
| Chân 11 | D7 — Data output bit 7 |
| Chân 12 | D6 — Data output bit 6 |
| Chân 13 | D5 — Data output bit 5 |
| Chân 14 | D4 — Data output bit 4 |
| Chân 15 | D3 — Data output bit 3 |
| Chân 16 | D2 — Data output bit 2 |
| Chân 17 | D1 — Data output bit 1 |
| Chân 18 | D0 — Data output bit 0 (LSB) |
| Chân 19 | DRDY — Data ready output |
| Chân 20 | OE — Output enable |
| Chân 21 | DVDD — Digital 5V supply |
| Chân 22 | DGND — Digital ground |
| Chân 23 | DVDD — Digital 5V supply |
| Chân 24 | DGND — Digital ground |
| Chân 25 | CLK — Clock input |
| Chân 26 | CLK — Clock input (complement) |
| Chân 27 | NC — Not connected |
| Chân 28 | NC — Not connected |
| Chân 29 | REFSEL — Reference select (internal/external) |
| Chân 30 | PD — Power down control |
| Chân 31 | NC — Not connected |
| Chân 32 | NC — Not connected |
| Chân 33 | AGND — Analog ground |
| Chân 34 | AVDD — Analog 5V supply |
| Chân 35 | AIN — Analog input (complement) |
| Chân 36 | AGND — Analog ground |
| Chân 37 | AVDD — Analog 5V supply |
| Chân 38 | AGND — Analog ground |
| Chân 39 | AVDD — Analog 5V supply |
| Chân 40 | NC — Not connected |
| Chân 41 | NC — Not connected |
| Chân 42 | NC — Not connected |
| Chân 43 | NC — Not connected |
| Chân 44 | NC — Not connected |
Ứng dụng tiêu biểu
IDTADC1006S055H-C1 phù hợp cho 6 Áp dụngs: Digital Oscilloscope Front-End, IF-Sampling Communications Receiver, Radar Signal Processing Digitiser, Medical Imaging Front-End, Industrial Test & Measurement, Video & Imaging Digitiser.
Digital Oscilloscope Front-End
The IDTADC1006S055H-C1 fits digital oscilloscope acquisition channels because of its 55 MSPS flash sampling, providing single-cycle latency for real-time waveform display. Flash architecture eliminates pipelined-ADC delay, which matters when reconstructing trigger-aligned pre-trigger samples. The 10-bit resolution captures typical scope vertical resolution, while the 44-QFP package supports commercial 4-layer PCB stackups. Single-channel input matches a standard scope probe-interface path after passive attenuation. Decouple AVDD and DVDD with 0.1 uF and 10 uF ceramic capacitors located adjacent to supply pins; on the clock input, drive CLK with a low-jitter CMOS oscillator to preserve ENOB and prevent SNR degradation.
Được đề xuất
IF-Sampling Communications Receiver
The IDTADC1006S055H-C1 suits narrowband IF-sampling receivers where 55 MSPS supports digitisation of IF bands up to ~25 MHz under Nyquist. Flash architecture's single-cycle latency simplifies the demodulator timing path, while the 10-bit resolution provides sufficient dynamic range for typical IF signals with AGC. Parallel CMOS outputs feed directly into FPGA or ASIC digital down-converters. The 5V analog/digital supplies match conventional receiver IF chain rails, simplifying power tree design. Filter the analog input with a passive anti-alias filter before the ADC, and route the CLK trace as a 50-ohm controlled-impedance line with short length to preserve timing margins.
Được đề xuất
Radar Signal Processing Digitiser
The IDTADC1006S055H-C1 is well placed in radar IF digitiser stages because its 55 MSPS flash conversion provides deterministic single-cycle latency, essential for matched-filter pulse compression. Radar systems depend on precise I/Q timing alignment across channels, and flash ADC's lack of pipeline delay simplifies alignment calibration. The 10-bit resolution is typical for legacy radar receiver designs where SNR is dominated by front-end LNA noise. The 44-QFP package supports MIL-spec conformal coating for defense applications. Use matched-length differential CLK traces, separate analog and digital grounds joined at a single point, and add a 1k series resistor on digital outputs to damp transmission-line ringing into the FPGA.
Được đề xuất
Medical Imaging Front-End
The IDTADC1006S055H-C1 serves medical imaging front-ends like ultrasound beamformer sub-arrays where 55 MSPS and single-cycle latency preserve phase coherence across transducer channels. Flash conversion ensures deterministic sample-to-output delay critical for beam-steering accuracy. The 10-bit resolution supports typical B-mode imaging dynamic range, while the 5V supply rails ease integration with ultrasound pulser receiver ASICs. Use a low-noise LDO on AVDD (e.g., 0.1 uF + 10 uF ceramic decoupling) and a separate LDO on DVDD to prevent digital noise coupling into the analog front-end. Place the reference bypass capacitor directly on the REF pin to reduce DNL errors.
Được đề xuất
Industrial Test & Measurement
The IDTADC1006S055H-C1 fits industrial ATE and benchtop instrumentation digitiser channels where 55 MSPS captures repetitive signals without aliasing. Flash architecture's single-cycle latency allows the digitiser output to feed directly into a comparator for trigger-decision logic, avoiding pipeline delay. The 44-QFP QFP package supports ruggedised multi-board stacks common in rack-mount instruments. The 5V analog/digital supplies match legacy instrumentation rails, easing integration with existing analog front-ends. Drive the ADC input through a transformer or differential driver for ground isolation, use a dedicated reference voltage IC to improve DNL, and provide a calibration register path to correct gain/offset drift over temperature.
Được đề xuất
Video & Imaging Digitiser
The IDTADC1006S055H-C1 fits video bandwidth digitiser cards in broadcast and surveillance equipment, where 55 MSPS oversamples NTSC/PAL component video at 4x oversampling, simplifying anti-alias filtering. Flash latency avoids pixel-by-pixel pipeline artefacts seen with pipelined ADCs in chroma demodulation paths. The 10-bit resolution preserves studio-broadcast dynamic range, while the 44-QFP commercial footprint supports standard video card manufacturing. Use a clamp circuit at the input to protect against hot-plug ESD events, drive CLK with a recovered or local 27 MHz reference, and add an LVDS-to-CMOS converter if downstream logic operates at LVDS levels.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho IDTADC1006S055H-C1 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | IDTADC1006S070H-C1 | IDTADC1006S040H-C1 | ADS5102IPFBR | ADS5220PFBRG4 |
|---|---|---|---|---|---|
| Package | 44-QFP (10x10) | 44-QFP (10x10) - same | 44-QFP (10x10) - same | 44-QFP - same footprint | QFP footprint - same family |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Texas Instruments | Texas Instruments |
| Resolution | 10 bit | 10 bit | 10 bit | 10 bit | 12 bit |
| Number of Inputs | 1 (single-channel) | 1 | 1 | 1 | 1 |
Bảo phân biệt quan trọng
- Flash architecture with single-cycle latency (vsModern pipelined ADC family)
- Same family higher-speed variant available (vsIDTADC1006S040H-C1)
- Wide distributor availability despite obsolete status (vsIDTADC1006S070H-C1)
Ghi chú thiết kế
Decouple AVDD and DVDD separately with 0.1 uF plus 10 uF ceramic capacitors placed within 5 mm of the supply pins. Keep analog and digital ground returns separated and joined only at a single point under the IC to avoid digital switching noise coupling into the analog signal path. Route the CLK signal as a 50 ohm controlled-impedance trace, length-matched to ensure timing margin between the same-family variants.
Do not assume all 44-QFP 10-bit ADCs share the same pinout: Renesas IDTADC1006S series and TI ADS5102IPFBR have different pin maps despite sharing the 44-QFP package. Always verify every supply, ground, input, CLK, and output pin against the datasheet before designing a PCB. Manufacturer-supplied IBIS models and pin-compatibility matrices should be requested before substitution.
Estimate: for 55 MSPS CMOS output edges (~3 ns rise time), a 2 cm output trace to a 4 pF downstream load produces ~6 mV of capacitive kick on AVDD via ground-bounce; a 100 ohm series damping resistor per output reduces this by ~80%. Place damping resistors within 5 mm of the ADC outputs. When driving an FPGA, use a series damping resistor and a 100 ohm differential termination on each CMOS pair if noise coupling is observed during layout sweeps.
Thông tin tuân thủ
Compliance flags not present in verified web data. The part is marked obsolete; for new designs requiring RoHS compliance, consult Renesas for a current-generation replacement.
