INA321EA/2K5 - Micropower RRO Instrumentation Amplifier | Texas Instruments
MPN: INA321EA/2K5 ✓ Hoạt độngINA321EA/2K5 Tóm tắt
An instrumentation amplifier is a differential analog amplifier optimized for measuring small signals superimposed on a larger common-mode voltage. The INA321 belongs to the hierarchy of instrumentation amplifiers, differential amplifiers, amplifier ICs, and analog semiconductors. Its differential input stage rejects common-mode interference while amplifying the voltage difference between its input terminals, making it useful for bridge sensors, biomedical instrumentation, and low-voltage current measurement.
Key features include a typical operating current of 40 uA, an offset voltage specified by the manufacturer at 500 uV maximum, a common-mode rejection ratio of 94 dB, and an input bias current of 10 pA. The shutdown function reduces quiescent current to below 1 uA. Its rail-to-rail output can approach the positive supply rail to within 0.02 V, while gain is established with external resistors. The high input impedance and low bias current are especially valuable when sensing high-source-impedance sensors.
The amplifier uses a CMOS instrumentation-amplifier architecture optimized for low power and single-supply operation. With a gain of 5 V/V, the listed bandwidth is 500 kHz, providing useful bandwidth for slow biomedical signals, industrial bridges, and general-purpose differential measurements. Because the output approaches the positive rail, correct common-mode range and output-swing calculations remain essential when operating near the supply limit.
Typical uses include low-power bridge-sensor conditioning, portable medical instrumentation, battery-powered sensor acquisition, current-shunt measurement, and precision analog front ends. The 40 uA operating current supports energy-limited systems, while shutdown supports duty-cycled measurement in which the amplifier remains inactive between readings. The low bias current minimizes disturbance from high-impedance sources.
When designing the circuit, place the gain-setting resistors close to the amplifier and verify the complete input and output common-mode range against the actual signal. If the input is unipolar, bias it near mid-supply rather than allowing a negative input excursion. Do not substitute a similarly packaged instrumentation amplifier unless its pin functions, gain architecture, common-mode range, and output-swing behavior have all been checked.
This product page combines the manufacturer's device specifications with practical application guidance, package information, pin mapping, sourcing guidance, and a comparison of available same-family choices. These engineering details help shorten component selection while keeping the decision focused on electrical compatibility rather than package name alone.
Bộ thay thế dễ dàng lắp đặt cho INA321EA/2K5 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
INA321EA/250
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
INA321E/2K5
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
INA321E/250
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
INA321EA/2K5G4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
INA321EA/2K5 Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Single-supply micropower CMOS instrumentation amplifier |
| Number of Circuits | 1 circuit |
| Typical Quiescent Current | 40 uA |
| Điện áp tắt | <1 uA |
| Maximum Offset Voltage | 500 uV |
| Low Offset Voltage | +/-200 uV |
| Common-Mode Rejection Ratio | 94 dB |
| Input Bias Current | 10 pA |
| Gain Accuracy Temperature Coefficient | 2 ppm/degree C |
| Gain | 5 V/V |
| Bandwidth at 5 V/V Gain | 500 kHz |
| Output Swing | Approximately V+ - 0.02 V |
| Điện áp cung cấp | 5.5 V |
| Supply Type | Single supply |
| Khoảng nhiệt độ hoạt động | -55 degrees C to +125 degrees C |
| Hộp | 8-pin VSSOP (DGK) |
| Kiểu lắp đặt | Surface mount |
| Gain Configuration | External resistor |
Cấu hình chân INA321EA/2K5
| Chân 1 | RG — Gain-setting resistor connection |
| Chân 2 | IN- — Inverting input |
| Chân 3 | IN+ — Noninverting input |
| Chân 4 | V- — Negative supply connection |
| Chân 5 | REF — Reference input for output-voltage biasing |
| Chân 6 | OUT — Amplified output |
| Chân 7 | V+ — Positive supply connection |
| Chân 8 | RG — Gain-setting resistor connection |
Ứng dụng tiêu biểu
INA321EA/2K5 phù hợp cho 6 Áp dụngs: Low-Power Bridge Sensor Conditioning, Portable Medical Signal Acquisition, Battery-Powered Current Measurement, Precision Industrial Pressure Interface, Battery-Powered IoT Sensor Node, Audio and Analog Front-End Buffering.
Low-Power Bridge Sensor Conditioning
The INA321EA/2K5 is well suited to bridge-based pressure, strain, and force sensors because its differential input rejects common-mode excitation variation while drawing only 40 uA of typical quiescent current. Place the sensor bridge across the supply and route its differential output to the amplifier inputs. The 94 dB common-mode rejection ratio helps suppress supply-related disturbance, while external resistors establish the required gain. The low 10 pA bias current reduces loading from high-impedance sensor nodes. Designers should still verify the bridge excitation voltage against the input common-mode range and ensure the output remains below the usable rail-to-rail swing.
Được đề xuất
Portable Medical Signal Acquisition
The INA321EA/2K5 supports low-energy medical and physiological signal acquisition when the sensed differential voltage remains within the amplifier's input and output limits. Its 40 uA operating current, below-1 uA shutdown current, 10 pA bias current, and 94 dB CMRR reduce loading and improve rejection of common-mode interference. The amplifier is placed between the sensor electrodes or bridge and a precision ADC, with gain established by external resistors. Because the output is rail-to-rail, system designers should provide suitable input biasing and verify patient-safety isolation requirements with an appropriate protection and isolation architecture.
Được đề xuất
Battery-Powered Current Measurement
The INA321EA/2K5 can measure the differential voltage across a low-ohm current shunt in a battery-operated system. Its common-mode rejection of 94 dB helps reject voltage changes that appear equally across the shunt and amplifier inputs, while the low 10 pA bias current limits measurement error. The device consumes 40 uA during operation and less than 1 uA in shutdown, enabling the measurement circuit to remain active only during a measurement interval. Choose the external gain resistors so the maximum expected shunt voltage does not saturate the output, and confirm that the common-mode voltage remains inside the permitted input range.
Được đề xuất
Precision Industrial Pressure Interface
The INA321EA/2K5 provides a compact analog front end for industrial pressure and position transducers that produce a small differential signal on a larger common-mode voltage. Its 94 dB common-mode rejection reduces sensitivity to cable pickup and ground differences, while 500 uV maximum offset supports low-level measurements when the total error budget permits. The amplifier operates from a single supply and approaches the positive output rail within approximately 0.02 V, making it useful for compact sensor modules. Use short input traces, a solid ground plane, and the gain resistors near the IC. Confirm the transducer excitation, input range, output range, and industrial temperature requirements before releasing the design.
Được đề xuất
Battery-Powered IoT Sensor Node
The INA321EA/2K5 fits compact IoT sensor nodes where a differential transducer must be measured from a single low-energy rail. Its 40 uA typical operating current limits continuous overhead, and the shutdown mode reduces supply current to below 1 uA between readings. The 10 pA input bias current is beneficial when the sensor source impedance is high, while the 500 kHz bandwidth listed at 5 V/V gain is substantially faster than many slow environmental sensors require. The designer should enable shutdown during idle periods, retain the gain resistors close to the package, and use the ADC's low-power conversion mode to complete the duty-cycled measurement sequence efficiently.
Được đề xuất
Audio and Analog Front-End Buffering
The INA321EA/2K5 can buffer and amplify small differential signals in low-level audio or analog front-end circuitry when the signal bandwidth is modest and supply current must remain low. Its 10 pA bias current reduces disturbance of high-impedance sources, and its rail-to-rail output provides useful headroom on a single supply. The 500 kHz bandwidth at 5 V/V gain is adequate for many control, monitoring, and low-frequency audio paths, although it is not intended for high-fidelity wideband audio. Use the external gain network to set the desired signal gain and verify the output's ability to swing both close to ground and close to the positive rail.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho INA321EA/2K5 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | INA321EA/250 | INA321E/2K5 | INA321E/250 | INA321EA/2K5G4 |
|---|---|---|---|---|---|
| Package | 8-pin VSSOP (DGK) | 8-pin VSSOP (DGK) | 8-pin VSSOP (DGK) | 8-pin VSSOP (DGK) | 8-pin VSSOP (DGK) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Typical Quiescent Current | 40 uA | 40 uA | 40 uA | 40 uA | 40 uA |
| Shutdown Current | <1 uA | <1 uA | <1 uA | <1 uA | <1 uA |
| Maximum Offset Voltage | 500 uV | 500 uV | 500 uV | 500 uV | 500 uV |
| Common-Mode Rejection Ratio | 94 dB | 94 dB | 94 dB | 94 dB | 94 dB |
| Input Bias Current | 10 pA | 10 pA | 10 pA | 10 pA | 10 pA |
| Bandwidth at 5 V/V Gain | 500 kHz | 500 kHz | 500 kHz | 500 kHz | 500 kHz |
| Gain Configuration | External resistor | External resistor | External resistor | External resistor | External resistor |
Bảo phân biệt quan trọng
- Very low active supply current (vsINA321EA/250)
- Strong common-mode rejection for bridge sensing (vsINA321E/2K5)
- Rail-to-rail output improves single-supply utilization (vsINA321EA/2K5G4)
Ghi chú thiết kế
Route the two differential inputs as a short, closely coupled pair and connect the external gain-setting resistors directly to the RG pins. Keep the input nodes away from switching nodes, high-current return paths, and the digital control return. The 10 pA bias current makes the amplifier suitable for high-impedance sources, but long PCB traces can still add leakage and capacitance. Use a continuous ground plane and place the device close to the source and gain resistors.
Do not assume that the output can reach the positive supply rail exactly. The manufacturer specifies a rail-to-rail output swing of approximately V+ minus 0.02 V. Leave the required output headroom when calculating gain from a unipolar sensor signal, and include reference-pin voltage in the output-voltage equation. Also verify the complete input common-mode range; a rail-to-rail output does not imply rail-to-rail input operation.
Use shutdown to reduce the supply current below 1 uA when measurements are infrequent. Place the local supply bypass capacitor close to the V+ and V- pins and provide a low-impedance ground return. For a single-supply circuit, bias the REF pin and signal inputs into the valid common-mode region. Account for the external resistor divider current when calculating total power and battery life because the 40 uA specification applies to the amplifier itself.
Thông tin tuân thủ
No RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations are stated in the manufacturer information identified for this product.