ISL81483IP - 1/8 Unit Load RS-485/RS-422 Transceiver | Renesas
MPN: ISL81483IP ✓ Hoạt độngISL81483IP Tóm tắt
An RS-485/RS-422 transceiver is an interface IC that converts logic-level transmit and receive signals into balanced differential bus signals. These differential signals reject common-mode noise and allow reliable data transfer over longer cables than single-ended interfaces. The transceiver also provides driver-enable and receiver-enable control so a node can transmit, receive, or remain inactive without driving the bus continuously.
Key characteristics of the ISL81483IP include a 1/8 unit-load bus loading factor, a 5 V supply, half-duplex operation, and support for both RS-485 and RS-422 networks. The low unit load is especially useful for large-node systems such as process automation and remote meter-reading installations, where every connected node adds loading to the bus.
The ISL81483IP uses a BiCMOS-oriented implementation described in the manufacturer datasheet as a fractional-unit-load transceiver family. Its driver and receiver functions are designed to meet the electrical requirements of balanced communication networks while keeping system power consumption low. The transceiver also provides separate receive and drive enables, allowing the host interface to control bus direction without external direction-control logic.
Typical uses include industrial process-control terminals, remote meter-reading nodes, building automation controllers, factory monitoring equipment, and RS-422 point-to-point links. The 8-pin PDIP package is appropriate for legacy control boards, prototype systems, and designs assembled by through-hole manufacturing processes.
When laying out an RS-485 board, place the transceiver close to the bus connector, route the differential pair as a matched pair, and provide a common-mode reference path for the connector shield. Keep the balanced traces away from switching nodes and high-current power paths. Use a termination resistor only where the bus topology requires it, and verify the cable length, node count, and baud rate against the transceiver's communication-distance guidance in the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho ISL81483IP — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
ISL81483IPZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ISL81483PZ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ISL81487PZ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ISL81487IPZ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ISL81483IBZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ISL81483IP Thông số kỹ thuật
| Product Type | RS-485/RS-422 half-duplex transceiver |
| Điện áp cung cấp | 5 V |
| Bus Unit Load | 1/8 unit load |
| Maximum Transceivers on Network | 256 transceivers |
| Communication Standard | RS-485 and RS-422 |
| Duplex Mode | Half-duplex |
| Number of Transceivers on Board | 1 |
| Hộp | 8-pin PDIP |
| Kiểu lắp đặt | Through-hole |
| Power Class | Low power |
| Driver Operating Mode | High speed or slew-rate limited |
| Receiver Output | Logic-level differential receiver output |
| Driver Enable | Yes |
| Receiver Enable | Yes |
| Termination | External bus termination as required by system topology |
Cấu hình chân ISL81483IP
| Chân 1 | RO — Receiver output |
| Chân 2 | RE — Receiver enable input |
| Chân 3 | DE — Driver enable input |
| Chân 4 | DI — Driver data input |
| Chân 5 | GND — Ground |
| Chân 6 | Y — Non-inverting driver output |
| Chân 7 | Z — Inverting driver output |
| Chân 8 | VCC — Positive supply |
Ứng dụng tiêu biểu
ISL81483IP phù hợp cho 6 Áp dụngs: Industrial Process Automation, Remote Utility Meter Reading, Building Automation Controller, Factory Monitoring Equipment, RS-422 Point-to-Point Link, Legacy Through-Hole Control Board.
Industrial Process Automation
The ISL81483IP fits process-automation field equipment that connects sensors, controllers, and remote I/O over a shared RS-485 bus. Its 1/8 unit-load input allows up to 256 transceivers on the network according to the Renesas datasheet, reducing the bus loading contributed by each node. The 5 V supply, separate driver-enable and receiver-enable controls, and low-power operation support compact controller designs. Use the slew-rate-limited driver option where slower edge rates improve compatibility with long cables or noisy industrial wiring, and place the device near the field connector.
Được đề xuất
Remote Utility Meter Reading
The ISL81483IP is suitable for apartment, building, or district-level meter nodes that report measurements to a concentrator through an RS-485 network. The fractional 1/8 unit load supports as many as 256 transceivers, matching the manufacturer datasheet example of remote utility-meter-reading systems. This allows many low-power meter endpoints to share one cable while limiting per-node loading. Choose the high-speed or slew-rate-limited mode according to cable length and environment, and use a consistent termination and shield strategy across the network.
Được đề xuất
Building Automation Controller
The ISL81483IP can connect a building-automation controller to HVAC equipment, lighting panels, access-control units, and environmental sensors sharing an RS-485 network. Its low unit load allows numerous controllers to coexist on one balanced bus, while the 5 V operation fits many embedded control boards. The half-duplex arrangement simplifies the direction of the link by using dedicated transmit and receive enables. For distributed building wiring, keep the balanced pair away from relay and motor-control traces, and validate ground referencing at the cable entry.
Được đề xuất
Factory Monitoring Equipment
The ISL81483IP supports factory monitoring equipment that combines motor controllers, environmental probes, counters, and remote diagnostics on an RS-485 backbone. A 1/8 unit load is valuable when many machine controllers are distributed over a plant floor, because it permits up to 256 transceivers according to the manufacturer documentation. The device also supports slew-rate-limited operation, which can reduce high-frequency ringing on longer cables. Keep the transceiver near the connector, maintain a matched differential trace pair, and separate the bus from high-current switching paths.
Được đề xuất
RS-422 Point-to-Point Link
The ISL81483IP also supports RS-422 point-to-point communication between two systems separated by a balanced cable. RS-422 provides a dedicated differential driver and receiver arrangement and is useful when a full-duplex link or a fixed two-node topology is preferred over a multidrop bus. The transceiver's 5 V operation and low-power design suit embedded equipment, while enable control lets the host park the driver when it is not transmitting. Verify the device's operating mode and enable polarity in the datasheet before applying it where continuous full-duplex operation is required.
Được đề xuất
Legacy Through-Hole Control Board
The ISL81483IP is appropriate for legacy industrial control boards, prototype platforms, and repair designs that use an 8-pin PDIP footprint rather than a surface-mount package. The through-hole package makes the part convenient for manual assembly and for maintaining older RS-485 hardware without redesigning the mechanical layout. Electrical compatibility still requires matching supply voltage, enable polarity, and the driver/receiver functions. Review the manufacturer's pin description and application circuit carefully, especially when replacing a transceiver with a different slew-rate option.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ISL81483IP — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ISL81483IPZ | ISL81483PZ | ISL81487PZ | ISL81487IPZ | ISL81483IBZ |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Product Type | 1/1 half-duplex RS-485/RS-422 transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver family | RS-485/RS-422 transceiver family | RS-485/RS-422 transceiver family | 1/1 half-duplex RS-485/RS-422 transceiver |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Bus Unit Load | 1/8 unit load | 1/8 unit load | 1/8 unit load family | 1/8 unit load family | 1/8 unit load family | 1/8 unit load family |
| Maximum Network Node Count | 256 transceivers | 256 transceivers | 256 transceivers family | 256 transceivers family | 256 transceivers family | 256 transceivers family |
| Duplex Mode | Half-duplex | Half-duplex | Half-duplex | Half-duplex | Half-duplex | Half-duplex |
| Driver Configuration | High speed or slew-rate limited | High speed or slew-rate limited | Family-specific configuration | Slew-rate-limited family option | Slew-rate-limited family option | High speed or slew-rate limited |
| Power Class | Low power | Low power | Low power family | Low power family | Low power family | Low power family |
Bảo phân biệt quan trọng
- Low fractional bus loading supports dense networks (vsISL81483IPZ)
- Supports both RS-485 and RS-422 physical layers (vsISL81487PZ)
- Through-hole package supports legacy and prototype assembly (vsISL81483IBZ)
Ghi chú thiết kế
Place the ISL81483IP close to the RS-485 connector and route Y and Z as a tightly matched differential pair. Keep the pair away from relays, switching-regulator nodes, and motor-drive outputs. Provide a continuous ground reference between the transceiver board and the connector shield, and use the manufacturer's recommended termination scheme because incorrect end-of-bus termination can reduce signal quality in multidrop networks.
The 1/8 unit load is a major system-level advantage because each ISL81483IP node contributes only one-eighth of a standard RS-485 load, supporting up to 256 transceivers according to the datasheet. Nevertheless, verify the combined node count, cable length, termination, and baud rate. Use the slew-rate-limited option on long or electrically noisy industrial cables, and validate the selected mode in the manufacturer's application guidance.
Do not assume that any device with the ISL81483 base name is mechanically interchangeable. The IBZ listing identifies an 8-SOIC package, whereas the ISL81483IP is an 8-pin PDIP. Confirm the package drawing, pin names, receiver-enable and driver-enable polarities, and temperature grade against the manufacturer datasheet before substituting a part in an existing PCB.
Thông tin tuân thủ
The manufacturer documentation confirms the ISL81483/ISL81487 family, 5 V operation, 1/8 unit loading, and RS-485/RS-422 support. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified in the verified product records.