Renesas Electronics

ISL81483IP - 1/8 Unit Load RS-485/RS-422 Transceiver | Renesas

MPN: ISL81483IP ✓ 啟用中
5 V Vdss 8-pin PDIP Package
MOQ: 1 |

ISL81483IP 概覽

The Renesas ISL81483IP is a single, half-duplex RS-485/RS-422 transceiver designed for 5 V balanced communication systems. It presents a 1/8 unit load to the RS-485 bus, allowing as many as 256 transceivers on a network, and it is available in an 8-pin PDIP package for through-hole industrial and instrumentation designs. The device supports low-power operation and offers high-speed and slew-rate-limited operating options for balancing communication distance against signal integrity. Its RS-485 and RS-422 compliance allows the same physical-layer device to serve multidrop industrial buses, point-to-point RS-422 links, process automation equipment, and remote utility-meter-reading concentrators.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level transmit and receive signals into balanced differential bus signals. These differential signals reject common-mode noise and allow reliable data transfer over longer cables than single-ended interfaces. The transceiver also provides driver-enable and receiver-enable control so a node can transmit, receive, or remain inactive without driving the bus continuously.

Key characteristics of the ISL81483IP include a 1/8 unit-load bus loading factor, a 5 V supply, half-duplex operation, and support for both RS-485 and RS-422 networks. The low unit load is especially useful for large-node systems such as process automation and remote meter-reading installations, where every connected node adds loading to the bus.

The ISL81483IP uses a BiCMOS-oriented implementation described in the manufacturer datasheet as a fractional-unit-load transceiver family. Its driver and receiver functions are designed to meet the electrical requirements of balanced communication networks while keeping system power consumption low. The transceiver also provides separate receive and drive enables, allowing the host interface to control bus direction without external direction-control logic.

Typical uses include industrial process-control terminals, remote meter-reading nodes, building automation controllers, factory monitoring equipment, and RS-422 point-to-point links. The 8-pin PDIP package is appropriate for legacy control boards, prototype systems, and designs assembled by through-hole manufacturing processes.

When laying out an RS-485 board, place the transceiver close to the bus connector, route the differential pair as a matched pair, and provide a common-mode reference path for the connector shield. Keep the balanced traces away from switching nodes and high-current power paths. Use a termination resistor only where the bus topology requires it, and verify the cable length, node count, and baud rate against the transceiver's communication-distance guidance in the manufacturer datasheet.

直接替換替代品,適用於 ISL81483IP — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

ISL81483IPZ

✅ 直接替換
📦 8-pin PDIP
Same PDIP-8 package and equivalent terminals; device grade and suffix details must be confirmed against the datasheets

📋 參考替代品(不在目錄中)

ISL81483PZ

✅ 直接替換 ⚠️ 規格未經驗證
📦 8-pin PDIP
Same-brand PDIP-8 family variant; enable and temperature-grade differences must be verified before substitution

📋 參考替代品(不在目錄中)

ISL81487PZ

✅ 直接替換 ⚠️ 規格未經驗證
📦 8-pin PDIP
Same-brand PDIP-8 transceiver family; the ISL81487 variant has a different slew-rate option, requiring driver-function verification

📋 參考替代品(不在目錄中)

ISL81487IPZ

✅ 直接替換 ⚠️ 規格未經驗證
📦 8-pin PDIP
Same-brand PDIP-8 family variant with a different slew-rate configuration; enable polarity and timing require confirmation

📋 參考替代品(不在目錄中)

ISL81483IBZ

✅ 直接替換
📦 8-pin PDIP
Same electrical family but distributor data identifies the IBZ ordering code as 8-SOIC, so it requires board footprint confirmation rather than direct PDIP substitution

📋 參考替代品(不在目錄中)

ISL81483IP 規格

Product Type RS-485/RS-422 half-duplex transceiver
供應電壓 5 V
Bus Unit Load 1/8 unit load
Maximum Transceivers on Network 256 transceivers
Communication Standard RS-485 and RS-422
Duplex Mode Half-duplex
Number of Transceivers on Board 1
封裝 8-pin PDIP
安裝類型 Through-hole
Power Class Low power
Driver Operating Mode High speed or slew-rate limited
Receiver Output Logic-level differential receiver output
Driver Enable Yes
Receiver Enable Yes
Termination External bus termination as required by system topology

ISL81483IP 腳位配置

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
腳位 1 RO — Receiver output
腳位 2 RE — Receiver enable input
腳位 3 DE — Driver enable input
腳位 4 DI — Driver data input
腳位 5 GND — Ground
腳位 6 Y — Non-inverting driver output
腳位 7 Z — Inverting driver output
腳位 8 VCC — Positive supply

典型應用

ISL81483IP 適用於 6 應用s: Industrial Process Automation, Remote Utility Meter Reading, Building Automation Controller, Factory Monitoring Equipment, RS-422 Point-to-Point Link, Legacy Through-Hole Control Board.

🏭

Industrial Process Automation

The ISL81483IP fits process-automation field equipment that connects sensors, controllers, and remote I/O over a shared RS-485 bus. Its 1/8 unit-load input allows up to 256 transceivers on the network according to the Renesas datasheet, reducing the bus loading contributed by each node. The 5 V supply, separate driver-enable and receiver-enable controls, and low-power operation support compact controller designs. Use the slew-rate-limited driver option where slower edge rates improve compatibility with long cables or noisy industrial wiring, and place the device near the field connector.

🧩

Remote Utility Meter Reading

The ISL81483IP is suitable for apartment, building, or district-level meter nodes that report measurements to a concentrator through an RS-485 network. The fractional 1/8 unit load supports as many as 256 transceivers, matching the manufacturer datasheet example of remote utility-meter-reading systems. This allows many low-power meter endpoints to share one cable while limiting per-node loading. Choose the high-speed or slew-rate-limited mode according to cable length and environment, and use a consistent termination and shield strategy across the network.

🏠

Building Automation Controller

The ISL81483IP can connect a building-automation controller to HVAC equipment, lighting panels, access-control units, and environmental sensors sharing an RS-485 network. Its low unit load allows numerous controllers to coexist on one balanced bus, while the 5 V operation fits many embedded control boards. The half-duplex arrangement simplifies the direction of the link by using dedicated transmit and receive enables. For distributed building wiring, keep the balanced pair away from relay and motor-control traces, and validate ground referencing at the cable entry.

🏭

Factory Monitoring Equipment

The ISL81483IP supports factory monitoring equipment that combines motor controllers, environmental probes, counters, and remote diagnostics on an RS-485 backbone. A 1/8 unit load is valuable when many machine controllers are distributed over a plant floor, because it permits up to 256 transceivers according to the manufacturer documentation. The device also supports slew-rate-limited operation, which can reduce high-frequency ringing on longer cables. Keep the transceiver near the connector, maintain a matched differential trace pair, and separate the bus from high-current switching paths.

🔗

RS-422 Point-to-Point Link

The ISL81483IP also supports RS-422 point-to-point communication between two systems separated by a balanced cable. RS-422 provides a dedicated differential driver and receiver arrangement and is useful when a full-duplex link or a fixed two-node topology is preferred over a multidrop bus. The transceiver's 5 V operation and low-power design suit embedded equipment, while enable control lets the host park the driver when it is not transmitting. Verify the device's operating mode and enable polarity in the datasheet before applying it where continuous full-duplex operation is required.

🔧

Legacy Through-Hole Control Board

The ISL81483IP is appropriate for legacy industrial control boards, prototype platforms, and repair designs that use an 8-pin PDIP footprint rather than a surface-mount package. The through-hole package makes the part convenient for manual assembly and for maintaining older RS-485 hardware without redesigning the mechanical layout. Electrical compatibility still requires matching supply voltage, enable polarity, and the driver/receiver functions. Review the manufacturer's pin description and application circuit carefully, especially when replacing a transceiver with a different slew-rate option.

What is the ISL81483IP used for?
The ISL81483IP is a single half-duplex RS-485/RS-422 transceiver used to connect a digital controller to a balanced industrial communication bus. According to the Renesas ISL81483/ISL81487 datasheet, it supports both RS-485 and RS-422 operation, consumes low power, and provides high-speed or slew-rate-limited driver options. The 1/8 unit-load characteristic makes it especially useful in distributed networks with many nodes.
What is the ISL81483IP bus loading and maximum node count?
The ISL81483IP presents a 1/8 unit load to the RS-485 bus. The Renesas ISL81483/ISL81487 datasheet states that this fractional loading allows up to 256 transceivers on the network, which supports large-node systems such as process automation and remote utility-meter-reading networks. Actual node count still depends on cable length, baud rate, topology, and termination.
Which package does the ISL81483IP use?
The ISL81483IP is supplied in an 8-pin PDIP through-hole package. The package identification is visible in the Renesas ISL81483 and ISL81487 datasheet family documentation and in distributor listings that identify the device as an 8-pin PDIP RS-485/RS-422 transceiver. Use the package drawing and pin-assignment table in the manufacturer datasheet when assigning PCB drill positions.
What are the key specifications of ISL81483IP?
The ISL81483IP is a 5 V, single, half-duplex RS-485/RS-422 transceiver with a 1/8 unit-load bus input. According to the manufacturer datasheet, it is designed for low-power operation and supports high-speed or slew-rate-limited driver configurations. The 8-pin PDIP package, separate driver and receiver enables, and support for both RS-485 and RS-422 are the principal application-level characteristics.
Where can I download the ISL81483IP datasheet PDF?
The official ISL81483 and ISL81487 datasheet is available from Renesas through the product document page. The document describes the fractional unit-load BiCMOS transceiver, electrical characteristics, pin assignments, and application information for RS-485 and RS-422 networks. Use the manufacturer datasheet for current ratings, timing limits, and the authoritative pinout before laying out a new board.
Where can I find the ISL81483IP pinout?
The ISL81483IP pin assignment is found in the pin-configuration and pin-description sections of the Renesas ISL81483/ISL81487 datasheet. The device uses an 8-pin PDIP arrangement with supply, ground, differential bus, data-input, and enable-related connections. Match every connection to the datasheet pin table, including the enable polarities, rather than relying on a generic RS-485 transceiver diagram.
Is the ISL81483IP suitable for a large RS-485 network?
Yes, the ISL81483IP is suitable for large RS-485 networks because its 1/8 unit-load input supports as many as 256 transceivers according to the Renesas datasheet. This makes it a strong fit for process automation, industrial monitoring, and remote meter-reading concentrators. Confirm the maximum cable length and recommended baud rate for the selected driver mode before releasing the design.
What is the best drop-in replacement for ISL81483IP?
The closest same-family replacement is the PDIP-packaged ISL81483IPZ, which is described as having the same functional characteristics, terminals, and package as the ISL81483IP. Before substitution, confirm the exact enable polarity, operating-temperature grade, and current lifecycle status in the manufacturer documentation. Request a quote for the selected MPN through the Request a Quote form on this page to confirm availability.
Can ISL81483IPZ replace ISL81483IP?
The ISL81483IPZ can serve as a candidate drop-in replacement for the ISL81483IP when both parts are the PDIP-8 package and the enable functions are electrically equivalent. A cross-reference listing describes the terminal and package arrangements as consistent and requiring no board modification. Production release should still follow a documented comparison of the Renesas datasheets for temperature grade, supply current, and timing.
When should I choose the ISL81483IP instead of a higher-speed RS-485 transceiver?
Choose the ISL81483IP when a low-unit-load, 5 V interface and a large node count matter more than maximum signaling rate. The 1/8 unit load permits up to 256 transceivers, while the slew-rate-limited option can improve compatibility on longer or noisier cables. Select a higher-speed device instead when the bus must operate at a baud rate beyond the ISL81483IP's rated capability.
Is ISL81483IP suitable for industrial and remote meter-reading systems?
The ISL81483IP is specifically suited to industrial and remote meter-reading networks. The manufacturer datasheet identifies process automation and remote utility-meter-reading systems as example applications for the 1/8 unit-load family. The device reduces the loading contributed by each node, allowing more equipment to share one balanced bus while maintaining a 5 V single-supply architecture.
What is the best Renesas equivalent for ISL81483IP?
The ISL81483IPZ is the closest same-manufacturer PDIP-8 alternative identified for the ISL81483IP because it is presented as a complete replacement with consistent terminals and functional characteristics. The related ISL81483IP and ISL81483IBZ listings show that suffix changes can alter the package, so package selection must follow the target board rather than the base device name alone.
Where can I buy ISL81483IP online?
Use the Request a Quote form on this page to request ISL81483IP pricing, stock confirmation, current lead time, and minimum order quantity. The manufacturer and distributor listings on this page can also be used to cross-check the 8-pin PDIP identification. Commercial terms may vary by quantity and purchasing schedule, so request a firm quotation for production planning.
What is the price of ISL81483IP?
Current commercial pricing for the ISL81483IP is available through the Request a Quote form on this page. The form is the appropriate route for quantity pricing, stock confirmation, and lead-time information because distributor pricing changes by order volume and contract. Request the exact PDIP-8 ordering code to ensure the quotation matches the intended package and grade.
How long is the lead time for ISL81483IP?
The current lead time for ISL81483IP should be confirmed through the Request a Quote form on this page. Lead time depends on manufacturer inventory, production status, quantity, and delivery schedule. The manufacturer lists the ISL81483 and ISL81487 family in its product documentation, so an active family does not by itself guarantee immediate shipment of a specific quantity.
Is ISL81483IP in stock?
Stock status for the ISL81483IP should be confirmed through the Request a Quote form on this page, which supports stock and delivery inquiries for the exact ordering code. Distributor search results may show in-stock status, but that status can change before an order is placed. Include the required quantity, target date, and PDIP-8 package confirmation with the request.

工程參考資料,適用於 ISL81483IP — 比較、設計指引及合規資訊。

選型指南

Choose the ISL81483IP for a 5 V, half-duplex RS-485 or RS-422 interface that uses an 8-pin PDIP footprint and benefits from a 1/8 unit load. It is especially appropriate for industrial process-control and remote meter-reading networks where many nodes share one cable and low power is important. The ISL81483IPZ is the closest same-family candidate when an equivalent PDIP-8 ordering code is required, provided the temperature grade and enable polarity are confirmed. Consider the ISL81487PZ or ISL81487IPZ when the required driver emphasis is the slew-rate-limited family option rather than the ISL81483 behavior. Do not select the ISL81483IBZ for an existing PDIP board solely because its electrical function is similar; the listed SOIC package requires a different PCB footprint. In every substitution, compare the datasheet pin table, enable polarity, timing, current limits, and operating-temperature grade before production release.

與替代品比較

參數 本產品 ISL81483IPZ ISL81483PZ ISL81487PZ ISL81487IPZ ISL81483IBZ
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Product Type 1/1 half-duplex RS-485/RS-422 transceiver RS-485/RS-422 transceiver RS-485/RS-422 transceiver family RS-485/RS-422 transceiver family RS-485/RS-422 transceiver family 1/1 half-duplex RS-485/RS-422 transceiver
Supply Voltage 5 V 5 V 5 V 5 V 5 V 5 V
Bus Unit Load 1/8 unit load 1/8 unit load 1/8 unit load family 1/8 unit load family 1/8 unit load family 1/8 unit load family
Maximum Network Node Count 256 transceivers 256 transceivers 256 transceivers family 256 transceivers family 256 transceivers family 256 transceivers family
Duplex Mode Half-duplex Half-duplex Half-duplex Half-duplex Half-duplex Half-duplex
Driver Configuration High speed or slew-rate limited High speed or slew-rate limited Family-specific configuration Slew-rate-limited family option Slew-rate-limited family option High speed or slew-rate limited
Power Class Low power Low power Low power family Low power family Low power family Low power family

主要差異化特點

  • Low fractional bus loading supports dense networks (對比ISL81483IPZ)
  • Supports both RS-485 and RS-422 physical layers (對比ISL81487PZ)
  • Through-hole package supports legacy and prototype assembly (對比ISL81483IBZ)

設計說明

Place the ISL81483IP close to the RS-485 connector and route Y and Z as a tightly matched differential pair. Keep the pair away from relays, switching-regulator nodes, and motor-drive outputs. Provide a continuous ground reference between the transceiver board and the connector shield, and use the manufacturer's recommended termination scheme because incorrect end-of-bus termination can reduce signal quality in multidrop networks.

The 1/8 unit load is a major system-level advantage because each ISL81483IP node contributes only one-eighth of a standard RS-485 load, supporting up to 256 transceivers according to the datasheet. Nevertheless, verify the combined node count, cable length, termination, and baud rate. Use the slew-rate-limited option on long or electrically noisy industrial cables, and validate the selected mode in the manufacturer's application guidance.

Do not assume that any device with the ISL81483 base name is mechanically interchangeable. The IBZ listing identifies an 8-SOIC package, whereas the ISL81483IP is an 8-pin PDIP. Confirm the package drawing, pin names, receiver-enable and driver-enable polarities, and temperature grade against the manufacturer datasheet before substituting a part in an existing PCB.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The manufacturer documentation confirms the ISL81483/ISL81487 family, 5 V operation, 1/8 unit loading, and RS-485/RS-422 support. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified in the verified product records.

資料驗證日期: 2026-11-15 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

ISL81483IP datasheet ISL81483IP datasheet pdf ISL81483IP pinout ISL81483IP specifications Renesas ISL81483IP ISL81483IP PDIP-8 ISL81483IP equivalent ISL81483IP replacement ISL81483IP vs ISL81483IPZ ISL81483IP price ISL81483IP RS-485 transceiver ISL81483IP remote meter reading ISL81483IP 1/8 unit load ISL81483IP RS-422 application

相關元件與詞彙

Renesas Electronics ISL81483IP ISL81483IPZ ISL81483PZ ISL81487PZ ISL81487IPZ ISL81483IBZ RS-485 RS-422 half-duplex transceiver balanced differential bus interface IC 1/8 unit load 5 V transceiver BiCMOS driver enable receiver enable slew-rate-limited driver high-speed driver process automation remote utility meter reading 8-pin PDIP through-hole package common-mode noise rejection industrial communication bus
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情