Renesas Electronics

ISL83490IB - 3.3V 10Mbps RS-485/RS-422 Transceiver | Renesas

MPN: ISL83490IB ✗ Cuối đời
3.3 V Vdss RS-422 and RS-485 Rds(on) 8-pin SOIC, 3.90 mm width Package
MOQ: 1 |

ISL83490IB Tóm tắt

The Renesas Electronics ISL83490IB is a 3.3 V, full-duplex RS-485/RS-422 interface transceiver capable of operation at 10 Mbps in an 8-pin SOIC package. It integrates one driver and one receiver for bidirectional point-to-point communication, providing a compact interface between differential bus wiring and a 3.3 V digital system. The operating temperature range is -40°C to +85°C, and the surface-mount package supports automated PCB assembly.

A differential transceiver is an interface IC that translates logic-level signals into balanced differential voltage pairs and converts received differential signals back into CMOS-compatible outputs. The RS-485 and RS-422 standards define the physical signaling method rather than the data protocol. This distinction allows ISL83490IB to carry data generated by UARTs, microcontrollers, industrial controllers, or other serial equipment while leaving packet framing and higher-layer control to the connected system.

The ISL83490IB provides one transmit driver and one receive channel, supports 3.3 V operation, and is specified for data rates up to 10 Mbps. Its full-duplex configuration permits simultaneous transmission and reception on separate differential pairs. This is advantageous for point-to-point links, industrial equipment connections, test systems, and embedded control networks where half-duplex bus arbitration would add unnecessary application complexity. The SOIC-8 package also keeps the interface compact while providing adequate pin spacing for conventional board assembly.

Renesas identifies the ISL83490 family as a low-power, high-speed RS-485/RS-422 transceiver family with operating variants described as high-speed or slew-rate-limited. The exact drive strength, receiver thresholds, bus loading, and propagation-delay limits should be taken from the pin-specific manufacturer datasheet before assigning a cable length or termination network. For long cables, incorrect termination, excessive stub lengths, or incompatible grounding can increase reflections even when the transceiver operates within its rated data rate.

Typical uses include industrial control links, factory equipment connections, building automation equipment, instrumentation, and embedded serial links. In these systems, the transceiver converts the controller's UART logic into a balanced differential signal and receives the remote signal with common-mode rejection. Board-level protection, isolation, surge handling, and ground strategy remain application-level concerns because the ISL83490IB is primarily a signal interface rather than a surge-protection device.

A robust layout should route the differential driver and receiver traces as a closely coupled pair with continuous reference planes, keep the driver output path short, and place any termination components near the appropriate connector or transceiver pin. Decoupling capacitors should connect directly to the device supply and ground pins with minimal loop area. Avoid adding large test pads or long stub branches to the bus traces, because such structures can degrade edge response at the supported 10 Mbps signaling rate.

This page combines lifecycle information, interface-family positioning, compatible ordering variants, package guidance, and application-oriented design considerations. It is intended to accelerate component selection and PCB planning while keeping the manufacturer datasheet authoritative for pin assignments, electrical limits, recommended operating conditions, and ordering information.

Bộ thay thế dễ dàng lắp đặt cho ISL83490IB — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ISL83490IB (cùng hình factor và footprint) — khác nhau ở Maximum Data Rate, Package, Product Type, Supported Standards.

Renesas Electronics
Maximum Data Rate: 250 kbps
Package: 8-lead SOIC
Product Type: Full-duplex RS-485/RS-422 transceiver
So sánh với ISL83490IB →

ISL83490IBZ

✅ Drop-In
📦 8-pin SOIC
Same 3.3 V, 10 Mbps, 1TX/1RX full-duplex interface and 8-pin SOIC footprint; ordering-code difference with no functional change stated

📋 Tham chiếu thay thế (không có trong danh mục)

ISL83490IBZ-T

✅ Drop-In
📦 8-pin SOIC
Same 3.3 V, 10 Mbps, 1TX/1RX interface and 8-pin SOIC footprint; -T identifies a delivery packaging option

📋 Tham chiếu thay thế (không có trong danh mục)

ISL83490IB-T

✅ Drop-In
📦 8-pin SOIC
Same 3.3 V, 10 Mbps, 1TX/1RX interface and 8-pin SOIC footprint; -T identifies a delivery packaging option

📋 Tham chiếu thay thế (không có trong danh mục)

ISL83490IB Thông số kỹ thuật

Product Type RS-485/RS-422 differential transceiver
Điện áp cung cấp 3.3 V
Maximum Data Rate 10 Mbps
Duplex Mode Full duplex
Transmitter Count 1
Receiver Count 1
Supported Standards RS-422 and RS-485
Hộp 8-pin SOIC, 3.90 mm width
Kiểu lắp đặt Surface mount
Khoảng nhiệt độ hoạt động -40°C to +85°C
Trạng thái vòng đời Obsolete

Hướng dẫn cấu hình chân ISL83490IB 8-pin soic, 3.90 mm width

Cấu hình chân cho ISL83490IB (8-pin soic, 3.90 mm width gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.

Bảng cấu hình chân 8-pin soic, 3.90 mm width cho ISL83490IB

Không có dữ liệu chân cụ thể sẵn có cho ISL83490IB.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

ISL83490IB phù hợp cho 6 Áp dụngs: Industrial Controller Field Bus, Building Automation Equipment, Test and Measurement Instrumentation, Embedded UART Communication, Robotics and Motor Control, Point-to-Point Data Links.

🏭

Industrial Controller Field Bus

The ISL83490IB fits full-duplex industrial links that carry controller data over balanced copper pairs. Its 3.3 V supply matches modern embedded logic, while the 10 Mbps rate provides ample bandwidth for command, status, and diagnostic traffic. The integrated transmitter and receiver create separate differential paths, avoiding half-duplex bus contention. Install termination at the physical bus endpoint and validate return loss over the intended cable length, since transceiver speed alone does not guarantee reliable communication in every topology.

🏭

Building Automation Equipment

The ISL83490IB can connect a low-voltage controller to field equipment over a full-duplex RS-485/RS-422 interface. The -40°C to +85°C rating supports equipment operating across industrial temperature ranges, and the 8-pin SOIC footprint simplifies compact controller-board designs. Use the device with isolated or non-isolated grounding appropriate to the building installation, and place protection elements at the cable entry so transient energy does not reach the transceiver pins.

🔧

Test and Measurement Instrumentation

For bench instruments and automated test equipment, the ISL83490IB provides a compact differential interface between a controller and remote fixtures. A 10 Mbps ceiling supports high-volume command exchange and status updates, while full-duplex operation permits simultaneous transmission and reception. Keep the high-speed differential route short and controlled, use a common reference plane, and verify the receiver behavior with the actual cable and connectors. Protection or isolation may be needed when fixtures are connected to external equipment.

🖥️

Embedded UART Communication

The ISL83490IB extends a 3.3 V UART or microcontroller through balanced RS-485/RS-422 wiring. Differential signaling improves noise immunity over longer interconnects than a single-ended interface, particularly in equipment cabinets containing motors and switching power converters. The separate driver and receiver channels support dedicated transmit and receive pairs. Configure the logic-side enables according to the datasheet and keep supply-return paths close to each signal route to minimize common-mode conversion.

⚡

Robotics and Motor Control

The ISL83490IB is suitable for command and feedback links between a robot controller and distributed motor-control electronics. Full-duplex operation allows controller commands to travel while position, current, and diagnostic information returns on separate differential pairs. The 10 Mbps capability is well above the throughput normally required for motor commands, leaving margin for expansion. Keep the bus interface away from motor-current paths, use a suitable chassis or cable ground strategy, and add surge protection where robots connect to long external cables.

🌐

Point-to-Point Data Links

The ISL83490IB works well in short point-to-point links where both endpoints transmit and receive independently. Its 3.3 V operation, 10 Mbps capability, and 8-pin SOIC package simplify interfaces between instrument subsystems, peripheral controllers, and remote I/O modules. Unlike a multidrop bus, a point-to-point arrangement normally uses one termination at the receiving end of each differential pair. Validate the receiver threshold and common-mode range against the complete system before release, particularly when ground-potential differences are possible.

What is the ISL83490IB?
The ISL83490IB is a 3.3 V, full-duplex RS-485/RS-422 transceiver with one transmitter and one receiver, specified for data rates up to 10 Mbps. According to the Renesas ISL83490 product page, the device is packaged in an 8-pin SOIC for industrial and embedded serial-interface designs. It converts between digital logic signals and balanced differential bus signals while leaving the communication protocol to a UART, microcontroller, or other host controller.
What are the key specifications of ISL83490IB that engineers should know?
The ISL83490IB combines a 3.3 V supply, 10 Mbps maximum signaling rate, full-duplex operation, one driver, and one receiver in an 8-pin SOIC package. The manufacturer identifies the device as an RS-485/RS-422 transceiver for low-power, high-speed differential communication. Its commercial operating range is -40°C to +85°C, and the package is intended for surface-mount assembly. Pin-specific electrical limits and propagation delays should be confirmed in the manufacturer datasheet.
Where can I download the ISL83490IB datasheet PDF?
The ISL83490 datasheet is accessible through the Renesas ISL83490 product-details page, which links directly to the family documentation. The part is also indexed on AllDataSheet under the ISL83490 and ISL83490IB document entries. For design release, use the Renesas copy as the controlling source because it defines the exact ordering code, recommended operating conditions, pin descriptions, electrical characteristics, and package drawings.
Where can I find the ISL83490IB pinout?
The ISL83490IB pinout is found in the pin-description table and package drawing of the Renesas ISL83490 manufacturer datasheet. The device uses an 8-pin SOIC with separate differential driver and receiver connections. Assign PCB nets directly from that table rather than inferring connections from similar RS-485 devices. In particular, verify the driver-enable and receiver-enable polarity, supply pins, ground connection, and differential signal names before fabrication.
What is the difference between RS-485 and RS-422 on the ISL83490IB?
RS-485 is primarily a multipoint differential bus standard, while RS-422 commonly describes a point-to-point differential interface. The ISL83490IB implements the electrical transceiver needed for both signaling approaches, but application-level topology, biasing, termination, and protocol behavior determine the final network. According to the Renesas family description, the device supports RS-485/RS-422 signaling up to 10 Mbps. Multi-drop bus design still requires correct idle bias and careful analysis of driver loading.
Can ISL83490IB operate at 10 Mbps?
Yes, the ISL83490IB is specified as a 3.3 V, high-speed RS-485/RS-422 transceiver with a maximum signaling rate of 10 Mbps. This rating applies under the manufacturer’s specified electrical conditions, including appropriate supply voltage, load, termination, and board configuration. Cable length, stub geometry, connector transition loss, and radiated-noise requirements can reduce the practical usable distance, so the bus topology must be checked independently of the transceiver’s headline data-rate specification.
ISL83490IB vs ISL83490IBZ - which one is better?
The ISL83490IB and ISL83490IBZ are functionally equivalent 3.3 V, 10 Mbps RS-485/RS-422 transceiver ordering options for the same 8-pin SOIC footprint. Cross-reference information identifies the ISL83490IBZ as a complete replacement for the ISL83490IB without PCB modification. Selection should therefore account for lifecycle status, current availability, and the required delivery packaging rather than expecting an electrical interface change between the two designations.
Is ISL83490IB suitable for full-duplex industrial communication?
The ISL83490IB is suitable for full-duplex differential links because it combines one transmitter and one receiver at rates up to 10 Mbps. It can support point-to-point industrial equipment, instrumentation, building automation, and embedded controller connections where separate transmit and receive paths are available. The -40°C to +85°C operating range supports industrial environments, while the 3.3 V supply suits modern controller platforms. Surge, isolation, and long-cable protection may require additional circuitry.
When should I choose ISL83490IB over a half-duplex RS-485 transceiver?
Choose the ISL83490IB when the application benefits from simultaneous transmission and reception or requires a dedicated point-to-point differential link. Its full-duplex architecture uses separate driver and receiver channels and avoids sharing a bus in time through bus arbitration. A half-duplex transceiver may be preferable when many nodes must share one pair of wires and protocol timing can prevent transmission collisions. The decision should follow the required topology rather than data rate alone.
What is the best drop-in replacement for ISL83490IB?
The ISL83490IBZ is the clearest drop-in replacement because it uses the same 8-pin SOIC interface, operates from 3.3 V, and supports full-duplex RS-485/RS-422 signaling at 10 Mbps. A published comparison identifies it as a complete replacement requiring no board modification. The renamed target is marked obsolete by one lifecycle listing, so engineers should confirm current lifecycle status and supply continuity with the manufacturer before releasing a new production design.
Can ISL83491IBZ replace ISL83490IB?
The ISL83491IBZ belongs to the same Renesas ISL8349x transceiver family and uses the same 8-pin SOIC format, but it should not be assumed to be a drop-in replacement solely from the shared family designation. Functional differences in receiver behavior, enables, or bus operation must be checked in the manufacturer datasheets for both exact ordering codes. Use ISL83490IBZ when exact electrical compatibility with ISL83490IB is required and no redesign is permitted.
Where can I buy ISL83490IB online?
Use the Request a Quote form on this page to request the ISL83490IB and confirm current availability, order quantity, and delivery timing. The device is an obsolete catalog part, so standard inventory may be limited and lifecycle confirmation is important before committing a new design. Request the exact MPN ISL83490IB rather than accepting a suffix or package code without checking the manufacturer ordering table.
What is the price of ISL83490IB?
Current pricing and availability for the obsolete ISL83490IB should be requested through the Request a Quote form on this page. The structured price shown with the product reflects the platform’s current sourcing position and may vary with quantity and delivery packaging. Because lifecycle status and inventory can change quickly for obsolete interface ICs, request a written quotation for the exact 8-pin SOIC ordering code before placing a production order.
What is the lead time for ISL83490IB?
The current lead time for ISL83490IB is established through the Request a Quote form on this page. As an obsolete catalog part, its availability may depend on remaining factory inventory, qualified channel stock, or approved lifecycle-extension planning. Provide the required annual and per-order quantities, date code requirements, and delivery destination when requesting the quotation so the response reflects the actual sourcing position.
Is ISL83490IB in stock?
Current ISL83490IB stock should be confirmed through the Request a Quote form on this page. The part is listed as obsolete by one distributor record, and the manufacturer continues to describe the associated ISL83490 family. Stock status for obsolete components can change independently of the family’s active variants. Request confirmation of the exact ISL83490IB suffix, package form, lot traceability, and production quantity before treating the device as available.
How should the ISL83490IB be laid out for reliable 10 Mbps operation?
Route the ISL83490IB differential lines as tightly coupled pairs on a continuous ground plane, keep the transceiver and termination network close to the connector or defined bus point, and minimize stubs and test-pad branches. Place supply decoupling directly between the device supply and ground pins. According to the manufacturer’s 3.3 V, 10 Mbps positioning, the interface can support high-rate signaling, but board parasitics, cable return loss, and grounding still require careful validation with an eye diagram or receiver test.

Dữ liệu tham khảo kỹ thuật cho ISL83490IB — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose ISL83490IB when maintaining an existing design that uses the exact obsolete ordering code and the required quantity is available through the sourcing process. For a new design or an exact functional substitution without a PCB change, ISL83490IBZ is the preferred choice because it retains the 3.3 V supply, 10 Mbps rate, full-duplex 1TX/1RX arrangement, and 8-pin SOIC footprint while the manufacturer identifies the IBZ ordering option as active. ISL83490IBZ-T and ISL83490IB-T can satisfy the same electrical interface when their designated delivery packaging matches the assembly process. Do not choose an ISL83491 or other related-family device solely by package count: verify enable polarity, receiver behavior, supply limits, and all pin functions in the manufacturer datasheet. For designs requiring multi-drop bus arbitration rather than dedicated full-duplex links, select a half-duplex transceiver instead.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này ISL83490IBZ ISL83490IBZ-T ISL83490IB-T
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Package 8-pin SOIC 8-pin SOIC - same footprint 8-pin SOIC - same footprint 8-pin SOIC - same footprint
Product Type RS-485/RS-422 transceiver RS-485/RS-422 transceiver RS-485/RS-422 transceiver RS-485/RS-422 transceiver
Supply Voltage 3.3 V 3.3 V 3.3 V 3.3 V
Maximum Data Rate 10 Mbps 10 Mbps 10 Mbps 10 Mbps
Duplex Mode Full duplex Full duplex Full duplex Full duplex
Transmitter and Receiver Count 1 transmitter, 1 receiver 1 transmitter, 1 receiver 1 transmitter, 1 receiver 1 transmitter, 1 receiver
Mounting Type Surface mount Surface mount Surface mount Surface mount

Bảo phân biệt quan trọng

  • Direct 10 Mbps full-duplex interface (vsISL83490IBZ)
  • No PCB modification for the closest ordering replacement (vsISL83490IBZ)
  • Separate differential transmit and receive paths (vsISL83490IB-T)

Ghi chú thiết kế

Route each differential pair as a tightly coupled, impedance-controlled trace with a continuous reference plane beneath it. Keep the ISL83490IB output section short, avoid test pads and branch stubs on the bus, and place termination only at the defined physical endpoint of the line. At 10 Mbps, even short discontinuities can create reflections that reduce receiver margin.

Place the device supply bypass capacitor directly across the supply and ground pins, with a short, low-inductance connection. Keep the ground return under the SOIC footprint and separate logic-supply routing from motor, relay, and power-converter paths. If the interface uses isolated power, confirm that the isolated-side ground and transceiver ground arrangement satisfies the receiver common-mode limits in the manufacturer datasheet.

Do not substitute ISL83491IBZ or another family member solely because it also uses an 8-pin SOIC. Although the family offers related products, receiver enables, shutdown behavior, and other functions can differ. For an exact board-level replacement of the ISL83490IB, use ISL83490IBZ after confirming lifecycle and ordering requirements, and compare the complete pin-description and electrical-characteristic tables.

Use the shortest practical connection from the transceiver to the cable connector, and place common-mode chokes or protection devices where their capacitive loading will not impair the intended 10 Mbps edge rate. Connect cable shields according to the installation’s grounding strategy. Validate radiated and conducted emissions after installation because enclosure grounding, cable geometry, and connector transitions can dominate the transceiver’s board-level behavior.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was identified for the exact ISL83490IB ordering code. Confirm material and qualification status with Renesas before use in regulated or automotive designs.

Dữ liệu được xác minh vào: 2026-11-15 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

ISL83490IB datasheet ISL83490IB pinout ISL83490IB datasheet pdf ISL83490IB equivalent ISL83490IB replacement ISL83490IB cross reference ISL83490IB vs ISL83490IBZ Renesas ISL83490IB ISL83490IB 3.3V 10Mbps ISL83490IB 8-SOIC pinout ISL83490IB RS-485 transceiver ISL83490IB price ISL83490IB stock what is ISL83490IB

Các bộ phận và thuật ngữ liên quan

Renesas Electronics ISL83490IB ISL83490IBZ ISL83490IBZ-T ISL83490IB-T ISL83491 RS-485 RS-422 differential transceiver interface IC full duplex half duplex 3.3 V 10 Mbps SOIC-8 surface mount SMD UART industrial control building automation test and measurement motor control differential signaling common-mode rejection
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ